Eureka Pearl Insert Handleiding

Eureka Heater Pearl Insert

Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Pearl Insert (8 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 50 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Operation & Installation Instructions

Pearl Insert

Please keep these instructions for future reference.Rev C 232345

Pearl Insert 16

AF Gason Pty. Ltd. reserves the right to modify or alter specications, material etc. in the interest of product improvement.

WARRANTY

1. Subject to clauses 2 & 3 of this warranty, A.F. Gason Pty Ltd ACN 004 667 556 warrants the follow components of its heaters against defects in workmanshiping

and/or materials for the following periods from the date of purchase:

a) the rebox for ten years;

b) the paint nish for a period of months if the purchaser has followed the instructions provided by Gason in the operation and Installation Instructions manual; and12

c) all other components for 12 months except the glass, re brick lining or bae plate if, in the opinion of Gason, these items have been damaged by impact.

2. This exten ded warranty does not apply;

a) if the heater is purchased from a person who has not been authorised by Gason to sell its products;

b) if, in the opinion of Gason, the heater or any other component has been subject to abuse, misuse, alteration, modication or has not been installed, operated or maintained in

accordance with the instructions provided by Gason; or,

c) to owners other than the original purchaser.

3. If you believe that the heater you purchased contains a manufacturing defect and you wish to make a claim under this warranty, please contact an authorised Gason service

centre to arrange for an assessment.

4. If, after assessing the heater, Gason determines that the heater contains a manufacturing fault, Gason may at its discretion:

a) replace the heater;

b) repair or replace specic components of the heater; or

c) provide a full refund.

5. Parts replaced under warranty are warranted for the balance of their original warranty period.

6. If, at the discretion of Gason, the heater or any part needs to be replaced, serviced or repaired at an authorised Gason service centre, then the person claiming under this

warranty must pay all costs associated with:

a) returning the heater; and

b) the delivery or collection of any new or repaired heater.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are en to a replacement or refund for a mtitled ajor failure and for

compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality

and the failure does not amount to a major failure.

Any benets you receive under these warranties are in addition to other rights and remedies that you may have as a consumer under law in relation to the heater to which

these warranties relate.

These warranties are given by:

AF Gason Pty Ltd

Blake Street

Ararat VIC 3377

Please contact us if you have any queries on:

Phone: 03 97633200

or email us via the “Contact Us” section of our website: www.gason.com.au

650

596

855

500

680

750

290 325

835

600

850

765 680

Eureka Pearl for

masonry installation

Package dimensions:

1075Wx660Dx800H

Eureka Pearl for

ZCC installation

Package dimensions:

915Wx695Dx1025H

*Compliance Plate is located on the rear of the appliance fascia or on ZCC.

Masonry & Zero Clearance Installation

Pearl Insert 2 Pearl Insert 15

Read and follow these instructions carefully before installing and

sing this appliance.

WARNING

Safety Warnings

• A ue re with resulting damage may occur if the appliance is not installed,

operated and maintained as per this booklet.

• Never place combustible materials such as wood, paper or furniture near the

appliance.

• This appliance is designed to burn dry wood. Do not burn rubbish, driftwood,

flammable liquids or any substance containing salts or corrosives.

• This appliance must not be installed and operated in an area where kerosene,

petrol, paint thinner or other ammable liquid is used or stored.

• The ue system must be inspected and cleaned annually or sooner if required.

Failure to do so could result in an excessive buildup of creosote which may

result in a ue re, which may damage the ue or cause damage to your home.

• The surface of the appliance becomes hot during operation. Do not touch the

surface of this appliance. Keep children away from this appliance during

operation. Do not allow anyone to operate this appliance who is not familiar

with this instruction booklet.

WARNING

Paint Curing and Care

Your heater is coated with the best available heat resistant paint. Even though

he paint has been baked after application, it may require further temperature

uring. It may, if you overre the heater on its rst re, discolour. For your rst

wo or three rings, never exceed medium air setting and always have the fan

n when above low burn. Do not wipe the heater while the paint is curing. After

he paint has cured the only maintenance required to maintain the heater’s nish

s to wipe it with a soft cloth. Do not use any commercial cleaners or solvents on

he paint nish.

e are proud of the presentation of our products. If at any time you need to

reshen up the paint, your local dealer has touchup paint available for purchase.

If you have any enquiries, please contact the dealer from whom you purchased your heater:

LEASE COMPLETE:

ealer Name

ealer Address

Phone:

lease attach your original purchase dockets to this booklet for future reference.

To aid heater installation, remove door, bae system and cast iron liners to reduce

overall heater weight.

Firewood

Getting the most out of your rewood

Firewood is a sustainable source of energy and when used correctly can provide a cost eective form of heating in your

home. Too often poor heating results and operational issues are attributed to using unseasoned wood which leads to

excess smoking, causing creosote buildup and dirty glass. Wood should be stored in a dry place where good ventalition is

available. Freshly cut wood should be stored for between 12-24 months before burning.

Use only hardwood with your Eureka Pearl.

Thermal eciency

A wood’s eciency does not depend only on its type, but also on its moisture content as well as the temperature of the

combustion chamber. To achieve a greater eciency and longer burn cycle out of your Eureka Pearl, without the emissions

of hazardous particulates, your wood must be well seasoned.

Ideally, wood should not be burnt when its moisture content is above 20%. A moisture meter to measure moisture content

is a handy addition.

0% moisture

100% thermal eciency

10% moisture

88% thermal eciency

30% moisture

63% thermal eciency

50% moisture

39% thermal eciency

An example of available thermal eciency for a piece of wood as a fuel source at varying moisture levels.

The combustion process of burning wood

When wood is heated up to approximately 100 degrees celsius, moisture begins to evaporate from the fuel. There is no

heating value from the wood at this point. As moisture releases from the wood, it reduces the eciency of the combustion

process robbing heat energy from the wood. This demonstrates the importance of dry and well seasoned wood.

As rebox temperatures reach 250-300 degrees celsius, wood solids begin to break down and release volatile gases which

ignite and produce heat.

From 300+ degrees celsius, the main energy available from wood is released when fuel vapors containing up to 60% of

the wood’s potential heat is released.

Understanding combustion principles and learning how to manipulate various conditions surrounding the operation of

your Eureka Pearl enables you to achieve maximum comfort and eciency from your Australian made wood heater.

Figure 14

This heater is painted in stovebrite Metallic Black - code 6309.

Pearl Insert 14 Pearl Insert 3

Installation

WARNING

Installation THE INS TALLATION OF THIS APPLIANCE MUST BE CARRIED OUT AS PER THIS

MANUAL AND THE FLUE MANU FACTURER’S SPECIFIC ATIONS.

WE RECOMMEND TH AT YOU USE A QUALIFIED INS TALLER TO RY TCAR OU

THE INS TALLATION.

If you have any other enquirie please contact the dealer from whom yo s, u

purchased your heate r.

THIS APPLIANCE WEIGHS IN EXCESS OF 200 KILOGRAM S. EEXTREME CAR

SHOULD BE TAKEN WHEN HANDLING THE APPLIANCE.

This heater is to be installed into a masonry replace or a Eureka Zero

Clearance Cabinet.

Section showing Installation

Figure 1. Masonry Installation

WARNING

Brick Removal

IF BRICKS REQUIRE REMOVAL WHEN PREPARING THE FIREPLACE, ENSURE

THAT YOU DO NOT EXPOSE COMBUSTIBLE MATERIALS BEHIND THE

BRICKWORK OR WEAKEN THE INTEGRAL STRUCTURE OF THE CHIMNEY.

AF Gason Pty. Ltd. accepts no liability whatsoever for any interpretation of AS/NZS 2918:2001.

It is important you understandithese installation instructions and minimum clearances to

combustible materials before selecting a position for your Eureka Pearl, to ensure safe and

correct installation is achieved.

Installation permit

Depending on your local authority requirements, a permit may be required for the installation

of your heater. It is your responsibility to arrange the same.

Installation into existing or masonry replace

The Eureka Pearl Insert can be installed into a masonry replace with a ue system that is in

accordance with the relevant sections of AS/NZS 2198:2001. No combustible or heat sensitive

material maybe placed closer then 1410mm from the top of the hearth/base of the appliance

and 55mm either side of the appliance’s fascia.

In a masonry replace installation, the minimum hearth depth of 550mm from the front of

the fascia panel must be achieved. In the instance the replace is raised above a combustible

oor, and it is desirable to reduce the hearth depth, please refer to the elevated installation

instructions on page 5 for hearth reduction information.

For detailed mantle clearance dimensions, refer Figure 4 on page 6.

If installing the Eureka Pearl under a combustible mantle, a hot air deector must be attached

onto the front of the fascia.

Installation into Zero Clearance Cabinet - ZCC

The Eureka Pearl Insert can be installed in conjunction with a Eureka ZCC into a wall enclosure

directly onto a oor or elevated above a oor.

The Eureka Pearl Insert conforms to AS/NZS 2918:2001 Appendix B, when the appilance is

placed in relation to combustible surfaces as per these installation instructions.

For additional clearance details, or access to the Eureka Pearl Insert Conformance Certicate,

please contact your local Eureka Dealer from whom you purchased your heater.

Troubleshooting

• isy FanNo

Turn the power o and remove the three pin plug from the power point . Remove door and carefully place to one side.

Remove the that hold the Remove the fascia four M8 Cap Screws . fascia onto the rebox . Remove switch mount panel.

Disconnect the wiring loom via the plastic joine r. Unscrew the wing nuts which hold the fan in position and remove

the fan. Clean any dust with a dry paint brush and vacuum the fan blades. Clean around the motor. After completion

place two or three drops of sewing machine oil on the shafts at the bearings. Replace the fan in reverse to the removal.

• F an not workin g

are rmly connected . If the fan still fails to function, remove the fan and switches by rstly removing knob o the rotary

switch by pulling it away from the heater. Undo the holding nut and pull the switch out.

Squeeze locator tabs together on the rear of the thermostat switch and push through outside of pedestal.

Disconnect the wiring from the power lead and remove the fan. Convey the same to the authorised Eureka Dealer from

whom you purchased your unit for service.

Replace in the reverse order.

• rAir cont ol ammin j g

Access to the air slide is available when the door is opened.

There are three screws holdi ng the ace. Unair slide in pl do them and remo ve the air slid e. Wipe any h yas or dust that ma

have accumul ted a on a sthe back of the ir lide or on the face of r. vthe heate If any burrs have de eloped on the eback of th

air lide or s on f of r, o athe ace the heate rub them with ne wet nd dry sand paper till you ha ve a andsmooth surface

edges. a ke wa aRepl ce the air slide and ma sure the shers and sp cers are on wthe bolts hen you screw the bolts back int o

the ace of the f hea r. ate Do not apply ny type of nt s wh as thlubrica to the air lide atsoever is will attract dust and ma ke the

slide stick .

• iNo overn ght bur n

Remove the air slide as per air control jamming and check that the air slide is hard against the face of the heate r. isIf it

loos tighten up the bolts holding the air slidee, to the face of the heate r. .Do not overtighten

Check that the door rope has an even indentation from If it is uneve its contact with the face of the rebox. n

and it appears as though air could leak through the seal , the door hinge and latch can be adjusted or the door rope may

need to be replaced. Refer door adjustments and rope replacement instructions.

WARNING

Overring

NEVER OPERATE THE HEATER WITH THE DOOR LOOSE, OR SUCH THAT THE FIREBOX

IS NOT AIR TIGHT. OVERFIRING COULD RESULT IN DETRIMENTAL WEAR AND TEAR

ON THE FIREBOX AND FLUE SYSTEM.

Check the power connection with another applianc If the power point is e. ok, shift focus to the fan or the switches.

Move thermostat switch into the ‘Override’ position, and select one of the three fan speeds. If the fan fails to function,

isolate power as above, remove fascia to gain access to loom. Check that the terminals on the loom and both switches

• Excessive ash build up

Some woods will give large amounts of ash despite how you run the heater. Others will give you very little. Use the wood

which is most convenient for you, as long as it is dry. After a period of time you will get to know when to empty your unit.

Bark will give you excessive ash. Try not to burn it. If you are burning wood that gives you charcoal, you may nd that after

running the heater say for 8 hours at maximum burn rate, the charcoal builds up excessively. An overnight burn will reduce

this charcoal back to a ne ash. If you are not ready to shut down for an overnight burn when you next fuel the stove, load

the stove with only one piece of wood and lay it across the rebox on top of the charcoal. Open the air control wide open

and you will nd the charcoal will burn down with the one piece of wood. Repeat the process until the ash level is

signicantly reduced.

• Excessive smoking - smoke entering the room maybe caused by:

• Insucient length of ue (Flue to be 4500mm minimum underneath the base of heater to underside of cowl)

Increase height of ue

• Flue downdraught - Consult dealer or increase height of ue.

• Creosote build up in ue - Remove cowl and clean ue as per cleaning instructions. Check moisture content of

wood.

Product specificaties

Merk:	Eureka
Categorie:	Heater
Model:	Pearl Insert

Heb je hulp nodig?

Als je hulp nodig hebt met Eureka Pearl Insert stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Heater Eureka

Eureka Stockade SRS5 Insert Handleiding

18 Juli 2023

Eureka Opal SRS4 Insert Handleiding

18 Juli 2023

Eureka Garnet SRS3 Insert Handleiding

18 Juli 2023

Eureka Opal SRS3 Freestanding Handleiding

31 Mei 2023

Eureka Garnet SRS2 Freestanding Handleiding

25 Mei 2023

Eureka Jewel Freestanding Handleiding

25 Mei 2023

Eureka Solitaire SRS2 Handleiding

2 April 2023

Eureka Ruby Freestanding Handleiding

8 Februari 2023

Eureka Pearl Insert Handleiding

5 Februari 2023

Eureka Ruby Insert Handleiding

17 Januari 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa 9330.44 Handleiding

18 December 2024

Hortus 211-413 Handleiding

18 December 2024

Yamazen HF-L122 Handleiding

18 December 2024

Yamazen HF-D121 Handleiding

18 December 2024

Yamazen HF-L121 Handleiding

18 December 2024

Universal Blue UCRA9104-24 Handleiding

18 December 2024

Orava VL-203 Handleiding

18 December 2024

SHX HL20OSZ Handleiding

16 December 2024

Stanley ST-125T-KFA-ES Handleiding

16 December 2024

Perel PHS2000 Handleiding

14 December 2024