Eureka Amari Pass 3 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Eureka Amari Pass 3 (4 pagina's) in de categorie Tent. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
ASSEMBLY INSTRUCTIONS
AMARI PASS 2 & 3 TENTS:
What's in the box: 1 Tent Body, 2 Tent Poles, 1 Fly Strut,
1 Tent Fly, 1 Carry Bag, 1 Pole Bag, 1 Stake Bag/ Stakes
Lay out the tent body.
Assemble the poles
and attach to the webs
diagonally across the
tent body.
Clip the tent body
to the poles.
Stake down the corner
loops. Work on the diagonal
to square the tent as you go.
Raise the poles.
Attach to the
tent where they
cross.
Reach under the
fly and wrap the
Velcro tabs around
the poles.
Attach the fly web
buckles to the tent.
Open fly vent and raise
the stay.
Stake out the fly
Pull out the vestibule triangle.
Push up/back the strut.
Stake the webs, then the
guyline.
Should look like this inside
when done.
JOHNSON OUTDOORS GEAR 6.12
Drape the fly over the tent so
the yellow webs meet.
Reach under the fly on
each side and attach
the dog bone web to
the pull out ring.
Good:
4 stakes /4 lines Best:
4 stakes /8 lines
REV E. AUG 12
SEAM SEALING:
We recommend use of a sealer such as Kenyon Seam Sealer 3 or McNett Outdoor
SeamGrip
®
.
• Work in a fully ventilated area.
• Set the tent up or lay the tent out flat. Taut seams allow for even application and
penetration of the sealer.
• Decide which seams need to be sealed. For example, seams that will be exposed
to rain, runoff, or ground level water are a must for sealing, while seams on
uncoated nylon or mesh panels don’t need treatment. There is no need to seal
the seams in the roof or the factory taped seams. We recommend sealing both
floor and fly seams and reinforcements.
• Apply sealant to the inside and outside of all exposed seams. Several thin layers
will work better than one thick layer. Read and follow manufacture's instructions.
STAKING:
All tents need to be staked down to keep them from blowing away. Securing the
tent by placing heavy objects inside is just not adequate.
• Once the tent body is erected, stake it out before the fly is put on. This enables
you to square the tent up to ensure that the fly goes on properly and that the
seams align with the frame. Pull the base of the tent taut between each web
stake out loop or ring & pin. Make sure that all corners are square. It is important
that you don’t stake the tent out too tightly. You will know it’s too tight, if the door
zippers can not be easily operated. Drive stakes through the web loops, or with
ring & pin, drive the stake just outside the ring so that the “J” hook catches it. Tie
a piece of cord or web into a loop through the ring to be used as a large stake
loop if needed.
• With the tent properly staked, drape the fly over the frame, attach its tent
connection points and stake down any pull outs.
• Do not attempt to remove the stakes by pulling on the tent becket loop, as this
could cause the fabric to tear. The best way is to pry on the stake itself.
Staking in special conditions:
• Sand. Use long, broad stakes with plenty of surface area in loose soil.
• Hard, Rocky, or Frozen Soil. Steel stakes work best. Store steel stakes
separately. Their sharp edges can cut fabric and leave rust stains, which might
damage your tent.
• Snow. Use “dead man” anchors. Tie tent to buried objects (branches, tent bags,
or stuff sacks filled with snow; or tie tents to snow shoes, skis, or ski poles,
which are stuck in the snow.
GUY LINES:
Do not depend upon staking alone to keep your tent secure during high winds. Most
tent models have built-in loops or rings at optimal guy out locations. It’s important
to put in the extra time guying out your tent. Correctly done, it can save your tent
during exceptional weather.
• Make sure that the top fly is securely attached to the tent frame. Ties, hook and
loop, or dog-bones and elastic loops are sewn to the underside of the fly for this
purpose.
• Attach parachute cord to the loops/rings and stake them in the ground three or
four feet from the edge of the tent. If staked too close to the tent, wind can cause
an upward pull that could dislodge the stakes.
• If your tent does not have loops or rings for guy outs, attach guy lines 1/3
to 1/2 of the way up the framework on the main sidewalls. This enables the
guy line to support the lower section of the pole, while the upper pole can
flex and deflect wind gusts. It is best to run two cords at an angle from the
side of the guy out. This prevents all movement, except toward the anchor.
The guy lines will work together through opposition. See illustrations
below:
CONDENSATION & VENTING:
Through perspiration and breathing, an adult gives off about a pint of water
overnight. If it cannot escape, the water vapor condenses to liquid. Most
often, water found in the tent is a result of this condensation rather than
from the tent leaking. Condensation often forms where the sleeping bag
touches the side of the tent, under the sleeping pad, or on coated surfaces
such as the door flaps. A tent’s double wall construction allows the vapor to
escape through the roof to the outside, keeping the inside of the tent dry.
Leave the windows partially open at night to provide cross ventilation and
further reduce condensation. Cross ventilation becomes more important in
very humid or extremely cold conditions when the permeable roof is less
effective. The features that enhance ventilation are windows, short-sheeted
flys (bottom venting), roof vents, and High/Low venting doors. These are
specific to each tent model.
Given the importance of proper ventilation, We use High/Low venting in most
of our tents. This allows cooler air in through the low vents and warmer,
moist air up and out through the high vents. High/Low venting is
accomplished within the inner tent via roof vents, doors and windows. It is
important to vent the vestibule. Unvented, it can inhibit airflow into the tent.
Our tent vestibules profit from the ability to “short sheet” by means of
zippers & toggles and staked vestibule pull outs create a bellowing effect.
Most of our tents are equipped with a High/Low venting door. This design
allows increased airflow into the tent from the bottom. Open the low
vent/window to admit cool air, allowing the warmer air out through the high
roof vents. When rain and wind prevent the low vent from being opened,
the high door vent can still be used. Fly overhangs or vestibules protect it.
ULTRAVIOLET LIGHT:
Ultraviolet light damage to tent fabric is caused by excessive exposure to
sunlight. While our fabrics are UV resistant, any synthetic fabric is
susceptible to UV degradation. UV damage will cause nylon and polyester
to become brittle and tear easily. We recommend that you use the rain fly
even on clear days. It acts as a sunscreen to the tent. A rain fly is both
easier and less expensive to replace if damaged. UV damage can be
minimized by erecting tents on shaded sites with low exposure to direct
sunlight.
GENERAL POLE CARE:
• Never let tent poles snap together as this can damage the pole end.
• Do not drop tent or pole bags on their ends and do not bounce a tent bag
on its end to get the tent out. These actions may cut the shock cord and
damage the pole ends.
• The aluminum frame may bend slightly and take a “set” through usage; this
normally does not affect the performance of the frame.
GENERAL TENT CARE:
• Sweep the tent floor daily to prevent damage from stones.
• Try not to wear shoes inside your tent.
• Use a ground cloth whenever possible.
• Do not keep food inside a tent. Hungry critters will chew through tent fabric
in search of food.
STORAGE:
• Make sure the tent is completely dry, then store loosely rolled, in a dry, cool
place. To prevent dust from collecting on the tent, cover it with a cloth. This
allows the nylon/polyester fabric to breathe.
• Ideally, the tent poles should be stored in their fully assembled state. This
reduces the tension on the shock cord, prolonging its life.
• The tent bag should be used only as a carry sack and not for storage.
COLOR TRANSFER:
• Do to the nature of tent fabrics, color can transfer from darker to lighter
fabrics when the two fabrics are in contact over time when wet, damp or
exposed to the combination of moisture and high heat. This does not effect
the tent's performance. To prevent / minimize color transfer, always make
sure your tent is completely dry prior to packing and storage.
CLEANING:
• Clean the tent by setting it up and wiping it down with a mild soap (liquid
hand soap) and lukewarm water solution. Rinse thoroughly and dry
completely. Never use detergent, washing machines or dryers because they
can damage the tent’s protective coating and seams. After cleaning, be sure
the tent is completely dry, especially the heavier, double-stitched areas such
as the seams, before storing or mold / mildew are likely to grow.
• Clean the tent poles with a cloth and lubricate them with silicone spray. This
is especially necessary after ocean side camping to remove salt spray so the
poles don’t corrode or stay gritty.
• Clean the zippers with a quick dip in water and then dry them off. This is
especially important if you’ve been camping in a location with sand/dirt. If
you don’t clean the zippers, the sliders will wear out and eventually the teeth
will become inoperable.
ALTERATIONS OR MODIFICATIONS:
DO NOT misuse, modify or alter this product in any way from its condition at
the time of sale. Alteration, modification or any use of this product contrary
to the accompanying written instructions shall void the warranty. Moreover,
any misuse, alteration or modification of the product shall absolve Johnson
Outdoors Gear LLC of any liability for property damages or injuries sustained
as a result of such misuse, modification or alteration.
LIMITED WARRANTY:
What Is Covered: Johnson Outdoors Gear LLC
warrants to the original
purchaser that its products are free from defects in material and workmanship,
for the life of the product, except as qualified below. The life of the product is
determined from the date of purchase until such time as the product is no
longer serviceable due to normal wear and tear.
What Is Not Covered:
Johnson Outdoors Gear LLC
shall not be responsible for the
natural breakdown of materials that occurs inevitably with extended use (e.g., Ultra
Violet (UV) light damage on tents, exhausted zippers), or defects caused by
accident, abuse, alteration, animal attack, storm damage, misuse or improper care.
THERE ARE NO OTHER EXPRESS WARRANTIES BEYOND THE TERMS OF THIS
LIMITED WARRANTY. IN NO EVENT SHALL JOHNSON OUTDOORS GEAR LLC BE
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES.
Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.
What Johnson Outdoors Gear LLC Will Do: If after inspection we find that a
product failed due to a manufacturing or material defect, we will repair or
replace the product, at our option, without charge.
How to Obtain Warranty Service: Return the product, freight prepaid, to the
Dealer from whom it was purchased; or, contact our Customer Satisfaction
Department for return authorization: toll free
905-634-0023
. Collect shipments
or shipments without return authorization cannot be accepted. The product
registration card packaged with our product need not be returned for the
warranty to be effective and for you to receive warranty service.
Repairs: If your
Johnson Outdoors Gear LLC
product needs service or repair
due to normal wear and tear, animal attack, accident or some other reason
that is not covered under the warranty we will provide the necessary service
for a reasonable charge, plus shipping and handling. We require that products
accepted for any repair be properly cleaned according to our recommended
care instructions. Please send your product or component that requires repair
(e.g., tent fly), postage prepaid, along with a description of what needs
attention. For service and repairs, please contact our Customer Satisfaction
Department: toll free
905-634-0023
How State Law Relates To This Warranty: This warranty gives you specific
legal rights, and you may have other rights that vary from state to state.
Our experience building quality outdoor
equipment goes back over 100 years!
Today, we manufacture sleeping bags,
screen houses, day-use shelters and
camping tents. We also design and
manufacture tents for the United
States Military rental and for the
industry.
See eurekatentscanada.com
From baseplate and digital
compasses to electronic
instruments, our sister brands,
Silva and Tech4o, put outdoor
technology at your fingertips.
See and tech4o.com silvausa.com
Our brands are part of the Johnson
Outdoors family of products. Visit all
the brands at johnsonoutdoors.com
We support the "Leave No Trace"
Seven Principles:
1. PLAN AHEAD AND PREPARE
2. TRAVEL & CAMP ON DURABLE SURFACES
3. DISPOSE OF WASTE PROPERLY
4. LEAVE WHAT YOU FIND
5. MINIMIZE CAMPFIRE IMPACTS
6. RESPECT WILDLIFE
7. BE COURTEOUS OF OTHER VISITORS
WARNING:
KEEP ALL FLAME AND HEAT SOURCES AWAY FROM THIS TENT FABRIC.
• This tent meets the flammability requirements of CPAI-84. The fabric may
burn if left in continuous contact with any flame source. The application
of any foreign substance to the tent fabric may render the flame-resistant
properties ineffective.
• Do NOT operate any device which burns fuel inside your tent. Combustion
consumes oxygen and can produce dangerous levels of carbon monoxide,
which could lead to serious injury or death.
JOHNSON OUTDOORS CANADA INC.
4180 Harvester Road, Burlington, Ontario L7L 6B6
INSTRUCTIONS DE MONTAGE
POUR LES TENTES
AMARI PASS 2 ET 3
Contenu de la boîte : 1 corps de tente, 2 mâts de tente, 1 étai
d'auvent, 1 auvent de tente, 1 sac de transport, 1 sac pour
mâts, 1 sac pour piquets, avec piquets compris
Étalez le corps
de la tente.
Assemblez les mâts
et attachez-les aux
boucles de sangle à
travers le corps de la
tente, en diagonale.
Attachez le corps
de la tente aux
mâts.
Haubanez les boucles aux
coins. Travaillez en diagonale
pour former un carré avec le
corps de la tente au fur et à
mesure.
Dressez les mâts.
Attachez-les au
corps de la tente,
à l'endroit où ils
se croisent.
Passez le bras
sous l’auvent pour
saisir les attaches
en Velcro et
attachez-les aux
mâts de la tente.
Attachez les boucles
de sangle de l’auvent
au corps de la tente.
Tirez sur la bouche
d'aération de
l’auvent pour l'ouvrir
et dressez l'étai.
Haubanez
l'auvent.
Tirez sur le triangle du vestibule
pour l'étaler. Pressez l'étai vers
le haut et vers l'arrière. Haubanez
les boucles de sangle et ensuite
fixez le hauban. Voici de quoi
l'intérieur de la tente devrait
avoir l'air une fois montée.
JOHNSON OUTDOORS GEAR 8.12-FRE
Drapez l’auvent par-dessus le
corps de la tente de manière à
ce que les boucles de sangle
de couleur jaune se rejoignent.
Passez le bras sous
l’auvent de chaque
côté et attachez la
sangle avec bouton
en bâtonnet à la
patte d’haubanage.
Product specificaties
| Merk: | Eureka |
| Categorie: | Tent |
| Model: | Amari Pass 3 |
Heb je hulp nodig?
Als je hulp nodig hebt met Eureka Amari Pass 3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Tent Eureka
2 Juni 2023
15 Mei 2023
13 Mei 2023
12 Mei 2023
10 Mei 2023
7 Mei 2023
6 Mei 2023
4 Mei 2023
3 Mei 2023
2 Mei 2023
Handleiding Tent
- Tent Philips
- Tent IKEA
- Tent Asaklitt
- Tent Babymoov
- Tent Bestway
- Tent Brunner
- Tent Dometic
- Tent Dwt-Zelte
- Tent Fiamma
- Tent Gerjak
- Tent Mx Onda
- Tent Perel
- Tent Rocktrail
- Tent Rollei
- Tent Skandika
- Tent Thule
- Tent Trigano
- Tent Velleman
- Tent Ventura
- Tent Walker
- Tent Woods
- Tent Jamet
- Tent Obelink
- Tent Crivit
- Tent Edges
- Tent Kayoba
- Tent Hamron
- Tent Big Agnes
- Tent Black Diamond
- Tent Camp Master
- Tent Camp Trails
- Tent Carl Denig
- Tent Chinook
- Tent Coleman
- Tent De Waard
- Tent Easy Camp
- Tent High Peak
- Tent Hilleberg
- Tent Jack Wolfskin
- Tent Kelty
- Tent Khyam
- Tent Mountain Hardwear
- Tent Nigor
- Tent Nomad
- Tent Outwell
- Tent OZtrail
- Tent Raclet
- Tent Robens
- Tent Sierra Designs
- Tent Trimm
- Tent Vango
- Tent Vaude
- Tent Vrijbuiter
- Tent Wechsel
- Tent Wilderness Equipment
- Tent Wynnster
- Tent Zempire
- Tent SereneLife
- Tent Aart Kok
- Tent Cabanon
- Tent Holtkamper
- Tent Goldcamp
- Tent Isabella
- Tent Thermex
- Tent Kathmandu
- Tent Sorara
- Tent MSR
- Tent LECO
- Tent TOOLPORT
- Tent Helsport
- Tent Robinhood
- Tent Casaria
- Tent Black Wolf
- Tent Nordisk
- Tent Grand Canyon
- Tent San Hima
- Tent Gazebo Penguin
- Tent Sojag
- Tent Calima
- Tent Yamazen
Nieuwste handleidingen voor Tent
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024
25 November 2024