Etekcity Lasergrip 1080 Handleiding

Etekcity Thermometer Lasergrip 1080

Lees hieronder de 📖 handleiding in het Nederlandse voor Etekcity Lasergrip 1080 (2 pagina's) in de categorie Thermometer. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Thank you for purchasing the Lasergrip 1080 Infrared Thermometer by
Etekcity. This easy-to-use device lets you conveniently and accurately
measure surface temperatures from a distance without the need of any
direct contact. Should you have any questions or concerns, feel free to
contact our helpful customer support team toll-free at 855.686.3835 or
by email at support@etekcity.com.
NOTE: The Lasergrip cannot measure the temperature of objects behind
glass. Inaccuracy may also occur when exposed to steam, dust or any
other contaminants in the air.
NOTE: The Lasergrip LCD will display ‘OH’ when the measured
temperature is above the measurable range, and will display ‘OL’ when the
measured temperature is below the measurable range.
NOTE: The Lasergrip cannot measure the
temperature of objects behind glass. Inaccuracy
may also occur when exposed to steam, dust or
any other contaminants in the air.
WARNING: THIS DEVICE PRODUCES LASER RADIATION. USE
CLASS 2
EXTREME CAUTION AT ALL TIMES WHEN LASER IS IN USE. DO NOT
LOOK INTO DIRECT OR REFLECTED LASER-LIGHT BEAM OR VIEW BEAM
WITH OPTICAL INSTRUMENTS. DO NOT AIM LASER-LIGHT AT ANOTHER
PERSON OR ANIMAL. LASER RADIATION MAY DAMAGE YOUR EYE. DO
NOT DISASSEMBLE THE DEVICE.
IMPORTANT: Read all of the instructions in this manual.
Failure to comply with the instructions in this manual or use
of the device, in ways other than the ones mentioned in this
manual, may result in hazardous radiation exposure.
Safety Use & Care
Features
Specications
Operation
Function Diagram
• DO NOT point the laser-light at another person or animal.
• DO NOT attempt to point laser-light at an aircraft.
• Avoid direct/indirect eye contact with the laser-beam. Laser radiation
may cause eye damage.
• DO NOT view the beam with optical instruments.
• In the vicinity of use, make any bystanders aware of the dangers of
looking directly into the laser beam.
• DO NOT allow children to operate the device.
• Use a 9V battery when replacing the battery within the device. Make
sure to insert the battery in accordance with the correct polarities.
• ALWAYS remove the batteries when cleaning the device.
• DO NOT use leaking batteries or dispose old batteries in fire.
• Remove battery for storage if the device is not being used for a
prolonged period of time.
• DO NOT disassemble the device or tamper with internal components.
Doing so will void any warranty.
• DO NOT touch the lens or wipe it using anything other than a soft
cloth or cotton swab.
• Laser guided targeting for aiming precision
• Narrow distance-spot ratio for accurate results at greater distances
• Safely measure hazardous or inaccessible objects
• Standard 9V battery powers up to 12 hours of cumulative use
• Auto-off after 15 seconds of inactivity
Measurement Range: -58°F ~ 1022°F (-50°C ~ 550°C)
Accuracy: ±2% / ±2°C
Resolution: 0.1°F / °C
Maximum Output: < 1 mW
Wavelength: 630 - 670 nm
Distance-Spot Ratio: 12:1
Response Time: < 500 ms
Emissivity (Adjustable): 0.1-1.0
Battery: DC 9V
1. LCD Display
2. Unit(°C/°F)/DOWN
3. Emissivity Adjustment Mode
4. UP/Laser Pointer/Backlight
5. Measurement Trigger
6. Battery Compartment
7. Laser Hole
8. IR Sensor
1. Low Battery
2. Laser On
3. Back-light On
4. Continue Scanning
5. °C / °F
6. Temperature Result
7. Max Temperature /
Emissivity Result
8. Max Temperature Sign
9. Adjustable Emissivity Sign
1. Once the battery is properly installed, press the measurement trigger
to activate the device.
2. Point the Lasergrip towards the surface of measurement.
3. Press and hold the measurement trigger and the laser will activate for
aiming guidance.
4. Keep holding the trigger as you move the Lasergrip if you wish to live
scan the surface area for temperature measurement.
5. Once the laser is pointed to the desired point of measurement, release
the trigger and the LCD display will lock the calculated temperature.
6. Press the measurement trigger once again to make another
measurement.
• Keep the thermometer away from electromagnetic fields produced by
objects such as arc welders and induction heaters.
• DO NOT expose the thermometer to direct sources of heat for
extended periods of time.
• The thermometer measures surface temperature, not internal
temperature. Do not use the Lasergrip as a reliable source to measure
body temperatures.
Surface Temperature Measurement
HOLD for continuous
temperature reading
RELEASE to lock the
temperature result
To switch between units of temperature
measurement, press the °C/°F button at any
time while the Lasergrip is on.
To activate and deactivate the laser, press the
laser pointer On/Off button at any time while the
Lasergrip is on.
To activate and deactivate the display backlight,
press and hold measurement trigger and then
press the display backlight On/Off button at the
same time.
To adjust the emissivity value before
measurement, press the emissivity adjustment
mode button, then use the UP and DOWM
buttons to navigate to the desired value. You
may refer to the emissivity reference chart for
correct surface emissivity values. To transfer
into Max Temperature Mode, press the mode
button again.
Unit Conversion
Laser Activation
Display Backlight Operation
Emissivity Adjustment & Max Temperature
Display Icon Key
Package Contents
1 x Etekcity Lasergrip 1080 Infrared Thermometer
1 x 9V DC Battery
1 x User Manual
Infrared Thermometer
Model No.: Lasergrip 1080
Questions or Concerns?
support@etekcity.com • (855)-686-3835
The emissivity of a material is its efficiency in emitting thermal energy.
Non-reflective surfaces have a higher emissivity (closer to 1) than
reflective surfaces (closer to 0). Inaccurate results may occur when
measuring reflective surfaces such as glass, polished wood, and granite.
The device certification information is
labeled directly on the device. The sticker is
located on the left side of the Lasergrip.
To take accurate temperature measurement of reflective surfaces with
low emissivity, adjust the emissivity value before measurement using the
reference chart. Or, place a strip of masking tape over the surface and
allow for it to adjust to the temperature of the surface for approximately
30 minutes. Measure the surface, scanning the taped section, eliminating
the issue of inaccuracy.
The Lasergrip 1080 measures surface temperature on the basis of
distance to spot diameter ratio (D:S). As the distance between the
thermometer and the surface increases, the total surface area measured
will also increase. With a distance to spot ratio of 12:1 the surface area
measured has a diameter of roughly 1/12 the distance.
For the most accurate results, make sure the target has a surface area
of twice the corresponding spot diameter. Insufficient surface area will
result in inaccurate results. The recommended distance to hold the
Lasergrip from the surface of measurement is 14.17 in (36 cm). This
creates a spot measurement area of 1.18 inches (3 cm) in diameter.
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including
interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by
the party responsible for compliance could void the user’s authority to
operate this equipment.
Federal Communication Commission
Interference Statement
Emissivity
Emissivity Of MaterialsDistance-Spot Ratio
The device warning and aperture safety
information are also labeled directly on the
device; the sticker is located on the right side
of the Lasergrip.
Any updates to the product information
(date of manufacturing and manufacturer
address) will be added as adhesive overlays.
A3_22D06_us
Warranty Information
Customer Support
Scan Here to Receive Exclusive News:
Your product comes with 2 years of warranty,
starting from the date of purchase.
1. Scan the QR code or visit etekcity.com/warranty.
2. Enter your purchase info to receive
exclusive news.
3. Learn about our quality customer support
and gain easy access to warranty
information.
*Please have your invoice and order ID ready before contacting
Customer Support.
Etekcity Corporation
1202 N. Miller St., Suite A
Anaheim, CA 92806
Support Hours
Mon–Fri,
9:00 am–5:00 pm PST/PDT
Email: support@etekcity.com
Toll-Free: (855) 686-3835
If you encounter any issues or have any questions about your new
product, please contact our helpful Customer Support Team.
FCC SDOC SUPPLIER’S DECLARATION OF
CONFORMITY
Etekcity Corporation hereby declares that this equipment is in
compliance with the FCC Part 15 Subpart B. The declaration
of conformity may be consulted in the support section of our
website, accessible from www.etekcity.com
A new pre-installed 9V battery comes in protective plastic wrap inside
your Lasergrip. Follow the steps below to properly install or replace the
battery.
1. Open the battery cover. For first-time use, take the battery out and
remove the plastic wrapper. [Figure 1.1]
2. Securely connect the battery to the battery terminals, making sure the
leads and terminals are connected correctly. [Figure 1.2]
3. Reinsert the battery back into the compartment.
4. Close the battery cover, making sure that the wires are tucked inside the
battery compartment.
[Figure 1.3 ]
Battery Installation & Replacement
NOTE:
• The low battery indicator will appear on the display when the power is running
low. Immediately replace the battery when the icon appears.
• Remove the battery before storing if the Lasergrip is not being used for a long
time.
[Figure 1.1]
9V Battery
[Figure 1.2]
[Figure 1.3]
PAIR
Material Feature Material Feature EmissivityEmissivity
Aluminium Oxidized 0.3 Human
Skin 0.98
Polished 0.02-0.04 Graphite Oxidized 0.20-0.60
Brass Oxidized 0.5 Plastic Non-
transparent 0.95
Polished 0.02-0.05 Rubber 0.95
Gold 0.01-0.10 Plastic
Cement 0.85-0.95
Iron Oxidized 0.7 Concrete 0.95
Steel Oxidized 0.70-0.90 Cement 0.96
Asbestos 0.95 Soil 0.90-0.98
Plaster 0.80-0.90 Mortar 0.89-0.91
Asphalt 0.95 Brick 0.90-0.96
Rock 0.7 Marble 0.94
Wood 0.90-0.95 Textile 0.90
Charcoal Powered 0.96 Paper 0.95
Carbon 0.85 Sand 0.90
Lacquerwork Lackluster 0.97 Clay 0.92-0.96
Carbon
Cement 0.90 Sand 0.9
Soap
Bubble 0.75-0.80 Glass 0.85-0.92
Water 0.93 Textile 0.95
Snow 0.83-0.90 Heated
Food 0.95
Ice 0.96-0.98 Plastic 0.95
Frozen
Foods 0.95 Oil 0.94
Ceramics 0.95 Steel and
iron 0.80
Limestone 0.98 Wool Natural 0.94
Paint 0.93 Lead Oxidized 0.5
Distance (D) to Spot (S) size D:S = 12:1
recommended
14.17 in
11.81 in
0.98 in 1.18 in

Product specificaties

Merk: Etekcity
Categorie: Thermometer
Model: Lasergrip 1080

Heb je hulp nodig?

Als je hulp nodig hebt met Etekcity Lasergrip 1080 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermometer Etekcity

Etekcity

Etekcity Lasergrip 1080 Handleiding

17 November 2024
Etekcity

Etekcity Lasergrip 1022D Handleiding

24 Juni 2023
Etekcity

Etekcity Lasergrip 774 Handleiding

23 Juni 2023

Handleiding Thermometer

Nieuwste handleidingen voor Thermometer

Owon

Owon TI219 Handleiding

21 December 2024
TFA

TFA 12.1004 Handleiding

21 December 2024
Optex

Optex PT-U80 Handleiding

16 December 2024
Optex

Optex PT-7LD Handleiding

16 December 2024
Ebro

Ebro TFI 260 Handleiding

15 December 2024
Ebro

Ebro TFI 54 Handleiding

15 December 2024
EMOS

EMOS E0522 Handleiding

13 December 2024
Senseca

Senseca PRO 111 Handleiding

11 December 2024
TFA

TFA Spira 30.3064 Handleiding

7 December 2024
TFA

TFA Base 30.3061 Handleiding

7 December 2024