Epson PowerLite W70 Handleiding

Epson Beamer PowerLite W70

Lees hieronder de 📖 handleiding in het Nederlandse voor Epson PowerLite W70 (4 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Quick Setup

IMPORTANT: Before using this product, make sure you read these instructions

and the safety instructions in the online User’s Guide.

Contents

Make sure your projector box includes all of these parts:

You can place the projector on almost any flat surface. See the online User’s

Guide for more information.

Connect the projector

External video source

You can connect an external video source with an HDMI cable (not included).

Caution: Do not turn on the video source before connecting it to the projector;

you may damage the projector.

Note: Some external video sources may require an optional HDMI adapter

cable.

1 Remove the rear cover of the projector.

2 Connect an HDMI cable to your video source’s HDMI output port.

3 Connect the other end of the HDMI cable to the projector’s HDMI

extension cable.

4 Pass the HDMI cable through the cable path as shown.

5 Replace the rear cover of the projector.

Streaming device

You can connect a streaming device inside the projector, such as an

Amazon Fire™ TV Stick or Roku® Streaming Stick®.

Note: The projector’s HDMI port does not support MHL.

1 Remove the rear cover of the projector.

2 Open the USB power cable clamp.

3 Connect your streaming device to the projector’s HDMI extension cable.

4 Connect the USB power cable to your streaming device and make sure the

device fits securely inside the projector.

Device’s power port on the side

Device’s power port on the bottom

Caution: Do not force a device into the projector; you may damage the

projector or the device.

PowerLite® W70/W75

5 Pass the USB power cable through the hook and clamp, depending on

the location of the power port on your streaming device as shown below,

then close the clamp to secure the cable.

Device’s power port on the side

Device’s power port on the bottom

6 Replace the rear cover of the projector.

Turn on the projector

1 Plug in the projector.

2 Press the power button on the projector or the projector remote

control. The power light flashes blue, then stays on.

3 The default language of the menu system is English. To select another

language, press the menu button on the projector remote control.

Select Settings and press Enter. Select Language and press Enter. Select

your language and press . Press the menu button to exit.Enter

Note: To shut down the projector, press the power button on the projector

or the remote control, then press the button again to confirm, if necessary.

Adjust the image

1 Move the focus lever on top of the projector left or right to adjust the

image sharpness.

2 To adjust the image height, press and hold the foot release lever on the

bottom of the projector to extend the front adjustable foot. Release the

lever to lock the foot in the desired position.

Using the remote control

Install the batteries as shown (two AAA batteries).

Access projector menus

Turn projector on or off

Enter a selection

Turn off audio and

video temporarily

Navigate menus

Change color mode

Turn volume up or down

Adjust image shape

(keystone)

Go back to previous

function

Control playback of

connected device

See the online User’s Guide for more information on using the remote control.

Troubleshooting

• If you see a message after turning on the projector, make sure No signal

your streaming device or HDMI cable is properly connected.

• If you see a blank screen, check the following:

• Make sure the power light on the projector is blue and not

flashing.

• Press the power button to wake the projector from standby or

sleep mode, if necessary.

•

If you see a blank screen when a computer is connected, check the

following:

• On some Windows® laptops, you may need to hold down the key Fn

and press or the function key that lets you display on an external F7

monitor. It may be labeled or have an icon such asCRT/LCD .

On Windows 7 or later, hold down the Windows key and press at P

the same time, then click Duplicate.

• If you’re using a Mac laptop, open System Preferences and

select Displays. Click the Arrangement tab and select the Mirror

Displays checkbox.

• If the projector does not respond to remote control commands, make sure

the batteries in the remote control are installed correctly. Replace the

batteries if necessary.

• The projector’s USB power cable can provide 2.0A of power. Make sure

your streaming device supports this specification.

Registration

online at www.epson.com/webreg.

Where to get help

Manual

For more information about using the projector, you can view or download the

online manual from the Epson website, as described below.

Internet support

Visit www.epson.com/support www.epson.ca/support (U.S.) or (Canada)

and search for your product for solutions to common problems. You can

download utilities and documentation, get FAQs and troubleshooting advice,

or e-mail Epson.

Telephone support services

To use the Epson® PrivateLine® Support service, call (800) 637-7661. This service

is available for the duration of your warranty period. You may also speak with a

support specialist by calling (562) 276-4394 (U.S.) or (905) 709-3839 (Canada).

Support hours are 6 am pm to 8 , Pacific Time, Monday through Friday, and 7 am

to 4 , Pacific Time, Saturday. Days and hours of support are subject to change pm

without notice. Toll or long distance charges may apply.

Optional accessories

For a list of optional accessories, see the online User’s Guide.

You can purchase accessories from an Epson authorized reseller. To find the

nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online

at www.epsonstore.com www.epsonstore.ca (U.S. sales) or (Canadian

sales).

Notices

Bluetooth Safety and Specifications

Contains Bluetooth® module model: DBUB-E207

This document provides safety instructions and describes the speciﬁcations. Read this

document carefully before use to ensure your safety and product performance.

Data transmission is always initiated by software, which is the passed down through

the MAC, through the digital and analog baseband, and ﬁnally to the RF chip. Several

special packets are initiated by the MAC. These are the only ways the digital baseband

portion will turn on the RF transmitter, which it then turns off at the end of the packet.

Therefore, the transmitter will be on only while one of the aforementioned packets is

being transmitted. In other words, this device automatically discontinues transmission in

case of either absence of information to transmit or operational failure.

This equipment is restricted to indoor operation only.

U.S. FCC Notices

Contains FCC ID: BKMAE-E207

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause interference to radio and television

reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

WARNING: The connection of a non-shielded equipment interface cable to this

equipment will invalidate the FCC Certiﬁcation or Declaration of this device and

may cause interference levels which exceed the limits established by the FCC for this

equipment. It is the responsibility of the user to obtain and use a shielded equipment

interface cable with this device. If this equipment has more than one interface connector,

do not leave cables connected to unused interfaces. Changes or modiﬁcations not

expressly approved by the manufacturer could void the user’s authority to operate the

equipment.

Industry Canada (IC) Notices

Contains IC: 1052D-E207

CAN ICES-3 (B)/NMB-3 (B)

This device complies with Industry Canada’s license-exempt RSSs. Operation is subject

to the following two conditions: (1) This device may not cause interference; and (2) this

device must accept any interference, including interference that may cause undesired

operation of the device.

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. This

equipment should be installed and operated keeping the radiator at least 20 cm

(7.9 inches) or more away from person’s body.

Supplier’s Declaration of Conformity

According to 47CFR, Part 2 and 15, Class B Personal Computers and Peripherals; and/or

CPU Boards and Power Supplies used with Class B Personal Computers:

We: Epson America, Inc.

Located at: 3840 Kilroy Airport Way

MS: 3-13

Long Beach, CA 90806-2469

Telephone: (562) 981-3840

Declare under sole responsibility that the product identiﬁed herein, complies with

47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed,

is identical to the representative unit tested and found to be compliant with the

standards. Records maintained continue to reﬂect the equipment being produced can

be expected to be within the variation accepted, due to quantity production and testing

on a statistical basis as required by 47CFR §2.906. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

Trade Name: Epson®

Type of Product: LCD Projector

Model: HA20A

Marketing Name: PowerLite W70/W75

Options:

Product name Model

Remote controller 2192767xx (x = 0-9)

Epson America, Inc. Limited Warranty

Two-Year or 7,500-hour Projector Limited Warranty

A. What Is Covered: Epson America, Inc. (“Epson”) warrants to the purchaser of the

Epson product enclosed with this limited warranty statement that the product, if

purchased and operated in the United States, Canada, or Puerto Rico, will be free

from defects in workmanship and materials for a period of two (2) years from the

date of original purchase or 7,500 hours of use, whichever occurs ﬁrst.

B. What Epson Will Do To Correct Problems: If your product requires service during

the limited warranty period, please call Epson at the number at the end of this

statement and be prepared to provide the model, serial number, and, if required,

date of original purchase. This line will be answered during Epson’s regular support

hours (currently 6:00 am pm to 8:00 , Paciﬁc Time, Monday through Friday, and 7:00 am

to 4:00 pm on Saturday - subject to change). You may also need to provide proof

of purchase if warranty coverage cannot be veriﬁed by the serial number. If Epson

conﬁrms warranty service is required, Epson will, at its option, exchange or repair

the product without charge for parts or labor. If Epson authorizes an exchange for

the defective unit, Epson will ship a replacement product to you, freight prepaid,

as long as you use an address in the United States, Canada, or Puerto Rico. The

replacement product may be new or refurbished to the Epson standard of quality.

(The replacement product may not include promotional materials, accessories,

documentation, manuals, software, or cables.) You are responsible for securely

packaging the defective unit and returning it to Epson within ﬁve (5) working days

of receipt of the replacement. Epson requires a debit or credit card number to secure

the cost of the replacement product in the event that you fail to return the defective

one. If Epson authorizes repair instead of exchange, Epson will direct you to send your

product to Epson or its authorized service center, where the product will be repaired

and sent back to you. You are responsible for securely packaging the product and

for all postage or shipping costs to and from the Epson authorized service center.

When warranty service involves the exchange of the product or of a part, the item

Product specificaties

Merk:	Epson
Categorie:	Beamer
Model:	PowerLite W70
Kleur van het product:	Wit
Gewicht:	2722 g
Breedte:	210.82 mm
Diepte:	231 mm
Hoogte:	91 mm
Geluidsniveau:	29 dB
Stroombron:	AC
Bluetooth:	Ja
Plaatsing:	Plafond
Oorspronkelijke beeldverhouding:	16:10
Meegeleverde kabels:	AC
Vaste focale lengte:	13.53 mm
Typische contrastverhouding:	2500000:1
Markt positionering:	Draagbaar
Projector helderheid:	2000 ANSI lumens
Projectietechnologie:	3LCD
Projector native resolution:	WXGA (1280x800)
Keystone correctie, verticaal:	± 45 °
Keystone correctie, horizontaal:	± 40 °
Geschikt voor schermmaten:	22 - 150 "
Projectie-afstand objectief:	- m
Aantal kleuren:	16.78 miljoen kleuren
Focus:	Handmatig
Brandpuntbereik:	- mm
Levensduur van de lichtbron:	12000 uur
Type lichtbron:	Laser
Bevestigingsmogelijkheid voor kabelslot:	Ja
Kabelslot sleuf type:	Kensington
Stroomverbruik (in standby):	- W
Zoomverhouding:	1.35:1
Throw ratio:	1.04 - 1.40
HDCP:	Ja
Verbruik (modus Economisch):	118 W
Duurzaamheidscertificaten:	RoHS
Verpakkingsinhoud:	PowerLite W70 projector, power cable, remote control, 2 AAA batteries, Documentation
Matrix type:	3-panel (p-Si TFT actief)
Projectiemodi:	Front, Rear
Afstandsbediening inbegrepen:	Ja
AC-ingangsspanning:	100–240 V
AC-ingangsfrequentie:	50/60 Hz
Stroomverbruik (typisch):	178 W
Bedrijfstemperatuur (T-T):	5 - 35 °C
Batterijen inbegrepen:	Ja
Type product:	Projector met normale projectieafstand
Video kleurenmodi:	Bright cinema, Cinema, Dynamic, Natural
Lichtopbrengst wit:	2000 ANSI lumens
Lichtopbrengst kleur:	2000 ANSI lumens