Epson PowerLite 800p Handleiding

Epson Beamer PowerLite 800p

Lees hieronder de 📖 handleiding in het Nederlandse voor Epson PowerLite 800p (120 pagina's) in de categorie Beamer. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/120

EPSON® PowerLite® 600p/800p/810p

Multimedia Projector

User’s Guide

Important Safety Information

WARNING: Never look into the projector lens when the lamp is turned on; the bright light can damage your eyes.

Never let children look into the lens when it is on. Never open any cover on the projector, except the lamp and

filter covers. Dangerous electrical voltages inside the projector can severely injure you. Except as specifically

explained in this User’s Guide, do not attempt to service this product yourself. Refer all servicing to qualified service

personnel.

WARNING: The projector and its accessories come packaged in plastic bags. Keep plastic bags away from small

children to avoid any risk of suffocation.

Caution: When you replace the lamp, never touch the new lamp with your bare hands; the invisible residue left by

the oil on your hands may shorten the lamp life. Use a cloth or glove to handle the new lamp.

any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior

written permission of SEIKO EPSON CORPORATION. The information contained herein is designed only for

use with this EPSON product. EPSON is not responsible for any use of this information as applied to other

products.

Neither SEIKO EPSON CORPORATION nor its affiliates shall be liable to the purchaser of this product or third

parties for damages, losses, costs, or expenses incurred by purchaser or third parties as a result of: accident, misuse,

or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the

U.S.) failure to strictly comply with SEIKO EPSON CORPORATION’s operating and maintenance instructions.

SEIKO EPSON CORPORATION shall not be liable for any damages or problems arising from the use of any

options or any consumable products other than those designated as Original EPSON Products or EPSON

Approved Products by SEIKO EPSON CORPORATION.

EPSON is a registered trademark of SEIKO EPSON CORPORATION.

EPSON Extra Care, EPSON Connection, and EPSON Store are service marks; SizeWise is a trademark; and

PrivateLine, Presenters Club, and PowerLite are registered trademarks of Epson America, Inc.

General Notice: Other product names used herein are for identification purposes only and may be trademarks of

their respective owners. EPSON disclaims any and all rights in those marks.

CPD-12788

Printed on recycled paper.

iii

Contents

Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Getting the Most from Your Projector . . . . . . . . . . . . . . . . . . 2

Using Your Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Reading This Manual Online. . . . . . . . . . . . . . . . . . . . . . 3

Getting More Information . . . . . . . . . . . . . . . . . . . . . . . . 4

Registration and Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Unpacking the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Additional Components . . . . . . . . . . . . . . . . . . . . . . . . . 7

Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1Setting Up the Projector . . . . . . . . . . . . . . . . . . . . . . 9

Positioning the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Connecting to a Laptop Computer . . . . . . . . . . . . . . . . . . . 12

Connecting the Computer Cable . . . . . . . . . . . . . . . . . 12

Connecting the Cable for Remote Mouse Control . . . . 13

Amplifying Computer Audio . . . . . . . . . . . . . . . . . . . . 14

Connecting to Video Sources . . . . . . . . . . . . . . . . . . . . . . . . 15

Connecting the RCA A/V Cable . . . . . . . . . . . . . . . . . . 16

Connecting an S-Video Cable . . . . . . . . . . . . . . . . . . . . 17

Connecting a Component Video Cable . . . . . . . . . . . . . 18

Using the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Turning On Your Equipment . . . . . . . . . . . . . . . . . . . . . . . 20

Turning On the Projector . . . . . . . . . . . . . . . . . . . . . . . 20

What To Do If You See a Blank Screen . . . . . . . . . . . . 22

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Focusing and Zooming Your Image. . . . . . . . . . . . . . . . 24

Adjusting the Height of Your Image . . . . . . . . . . . . . . . 25

Adjusting the Image Shape. . . . . . . . . . . . . . . . . . . . . . . 26

Resizing the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Adjusting the Tracking and Synchronization . . . . . . . . . 27

Controlling the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Switching Between Picture Sources . . . . . . . . . . . . . . . . 28

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning Off the Picture and Sound . . . . . . . . . . . . . . . 28

Shutting Down the Projector . . . . . . . . . . . . . . . . . . . . . . . . 29

3Using the Remote Control . . . . . . . . . . . . . . . . . . . 31

Turning On and Using the Remote Control . . . . . . . . . . . . 32

Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Turning On the Remote Control. . . . . . . . . . . . . . . . . . 32

Using the Remote Control. . . . . . . . . . . . . . . . . . . . . . . 33

Controlling the Picture and Sound. . . . . . . . . . . . . . . . . . . . 33

Switching Between Picture Sources . . . . . . . . . . . . . . . . 33

Adjusting the Volume . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Turning Off the Picture and Sound . . . . . . . . . . . . . . . 34

Stopping Action. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Zooming Your Image. . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Resizing the Image. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Displaying Picture-in-Picture Video . . . . . . . . . . . . . . . 36

Highlighting Your Presentation . . . . . . . . . . . . . . . . . . . . . . 37

Using the Pointer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Spotlighting Your Image . . . . . . . . . . . . . . . . . . . . . . . . 38

Using Horizontal and Vertical Highlights . . . . . . . . . . . 38

Using the Remote Control as a Wireless Mouse . . . . . . . . . . 39

Fine-tuning the Projector. . . . . . . . . . . . . . . . . . . . 41

Using the Projector’s Menu System . . . . . . . . . . . . . . . . . . . 42

Changing Menu Settings . . . . . . . . . . . . . . . . . . . . . . . . 43

Adjusting the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Repositioning the Image . . . . . . . . . . . . . . . . . . . . . . . . 46

Adjusting Image Appearance . . . . . . . . . . . . . . . . . . . . . 46

Saving and Recalling Computer Settings . . . . . . . . . . . . 48

Adjusting the Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Customizing the Highlighting Tools . . . . . . . . . . . . . . . . . . 50

Creating Your Own Startup Screen. . . . . . . . . . . . . . . . . . . . 51

Capturing the Image . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Choosing When to Display the Image . . . . . . . . . . . . . . 52

Customizing Projector Features . . . . . . . . . . . . . . . . . . . . . . 53

Setting Advanced Features . . . . . . . . . . . . . . . . . . . . . . . 55

Viewing Lamp Usage and Other Information. . . . . . . . . . . . 56

Restoring the Default Settings . . . . . . . . . . . . . . . . . . . . . . . 57

5Maintaining and Transporting the

Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Cleaning the Lens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cleaning the Projector Case . . . . . . . . . . . . . . . . . . . . . . . . . 60

Cleaning and Replacing the Air Filter . . . . . . . . . . . . . . . . . . 61

Replacing the Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Resetting the Lamp Timer . . . . . . . . . . . . . . . . . . . . . . . 65

Transporting the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . 66

6Solving Problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Using On-Screen Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

What To Do When the Lights Flash. . . . . . . . . . . . . . . . . . . 69

Solving Problems with the Image or Sound . . . . . . . . . . . . . 72

Solving Problems with the Remote Control . . . . . . . . . . . . . 78

Where To Get Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Telephone Support Services . . . . . . . . . . . . . . . . . . . . . . 79

Connecting to Additional Equipment. . . . . . . 81

Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Connecting to an External Audio System . . . . . . . . . . . 83

Connecting to a PC Desktop Computer . . . . . . . . . . . . . . . 84

Connecting the Computer Cable . . . . . . . . . . . . . . . . . . 84

Connecting the Mouse Cable. . . . . . . . . . . . . . . . . . . . . 86

Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . 87

Connecting to a Desktop Macintosh . . . . . . . . . . . . . . . . . . 88

Connecting the Computer Cable . . . . . . . . . . . . . . . . . . 88

Connecting the Mouse Cable. . . . . . . . . . . . . . . . . . . . . 90

Connecting the Audio Cable . . . . . . . . . . . . . . . . . . . . . 91

Connecting to a Second Computer . . . . . . . . . . . . . . . . . . . 92

Connecting to a High-End Workstation . . . . . . . . . . . . . . . 93

Connecting to a DVI Video Source . . . . . . . . . . . . . . . . . . . 93

BAppendix B: Notices. . . . . . . . . . . . . . . . . . . . . . . . . 95

Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . 95

Remote Control Information . . . . . . . . . . . . . . . . . . . . . . . . 97

Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . 98

FCC Compliance Statement. . . . . . . . . . . . . . . . . . . . . . . . . 99

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

CAppendix C: Technical Specifications. . . . . . 103

General. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103

Projection Lamp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Mouse Compatibility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Electrical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105

Compatible Video Formats . . . . . . . . . . . . . . . . . . . . . . . . 106

Computer Video Port Pin Assignments . . . . . . . . . . . . . . . 108

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

Welcome 1

Welcome

The EPSON® PowerLite® 600p, 800p, and 810p are portable

projectors that weigh less than 10 pounds and offer up to 2000 ANSI

lumens of brightness. From classrooms to auditoriums, your full-color

presentations and videos will be bright and visible even in ordinary

room lighting.

Images are displayed at a resolution of 1024 × 768 pixels (PowerLite

800p and 810p) or 800 600 pixels (PowerLite 600p). The 0.9-inch ×

LCD provides a high contrast ratio for incredibly vivid images and

clear text. Improved color processing technology reduces “video noise”

for rich, saturated images, while 5-watt amplified sound and

whisper-quiet operation contribute to theater-quality video.

With EPSON’s patented SizeWise™ chip, the projector supports

computer displays ranging from VGA through UXGA (or SXGA on

the PowerLite 600p). The projector also supports the new Digital

Visual Interface (DVI) format.

You can connect the projector to a wide range of computers, including

IBM® compatible PCs and laptops, Apple® Macintosh,

Power

Macintosh™ series (including G3 and G4 systems), PowerBook

computers, many iMac™ and iBook™ series systems, and high-end

workstations such as the Sun® SPARCstation.

™

You can use any of the following video sources: VCR, DVD player,

camcorder, digital camera, or laser disc player. The projector supports

composite video, S-Video, and component video, and it automatically

senses the video format (HDTV, NTSC, PAL, or SECAM).

Support for USB audio and new horizontal keystone control

contribute to ease of setup in a wide variety of environments.

2Welcome

Getting the Most from Your Projector

Your EPSON PowerLite projector is a highly versatile presentation

tool. You can connect it to one or two computer sources and up to

three video sources and easily switch between them. You can also

include sound for up to three of the sources.

Depending on your presentation, you can take advantage of any or all

of these options:

■Connecting to a laptop or other computer

If you want to connect to a PC laptop or Macintosh PowerBook,

see page 12. To connect to a desktop computer, a workstation, a

computer that outputs video in Digital Visual Interface (DVI)

format, or more than one computer, see Appendix A.

■Connecting to video sources

You can connect a DVD player, VCR, camcorder, laser disc

player, digital camera, or any other video source to your projector.

You can connect up to three video sources at the same time (with

or without a computer) and easily switch between them.

See page 15 for instructions.

■Using the remote control

The remote control lets you switch from one computer or video

source to another, with access to picture-in-picture, pointer,

zoom, and many other projector features. For details, see

Chapter 3.

By connecting an additional cable, you can also use the remote

control as a wireless mouse. This lets you click through

slideshow-style presentations (such as PowerPoint

®) from up to

30 feet away. For more information, see page 39.

■Including sound in your presentation

If your presentation includes sound, you can connect the USB

cable or an optional audio cable to use the projector’s built-in

speakers. For details, see page 14 (for laptops) or Appendix A (for

other systems).

note

You can connect a maximum

of four sources at the same

time.

Welcome 3

If you’re permanently installing the projector, you may wish to

connect external speakers or a public address system to the

projector’s Audio Out port; see page 83.

Using Your Documentation

To connect the projector to your laptop and get your presentation

up and running fast, see the Quick Setup sheet in your Owner’s Kit.

This book contains all the information you need to set up and use

your projector. Please follow these guidelines as you read through it:

■Warnings must be followed carefully to avoid bodily injury.

■Cautions must be observed to avoid damage to your equipment.

■Notes contain important information about your projector.

Reading This Manual Online

Your PowerLite CD-ROM includes an electronic copy of this manual.

You may find it convenient to copy it onto your laptop’s hard drive so

it’s always with you—for example, when taking your presentation on

the road.

To view your electronic manual, you need to use Adobe

® Acrobat®

Reader. Just insert the CD-ROM in your CD-ROM drive, select the

Install/View User’s Guide button and click

Install User’s Guide or

View User’s Guide.

When you open the manual, you see this toolbar:

note

If you do not have Acrobat

Reader, you can install it

from the CD-ROM.

first page last page

show

navigation pane

4Welcome

You can move quickly to the topic of your choice by clicking in the

table of contents on the left side of the screen. You can also use the

arrow buttons in the toolbar or on the vertical scroll bar on the right

side of the screen to move through the manual.

For more information, see your Acrobat Reader online guide.

Getting More Information

Need tips on giving presentations? Quick steps for setting up your

projector? Here’s where you can look for help:

■presentersonline.com

Includes a library of articles covering presentation tips, tricks, and

technology. The site provides templates, clip art and sound clips,

as well as Presenters Services to use on the road. Even more

resources and services are available if you register to join the

Presenters Club®— ’and it s free.

■Quick Setup sheet

Gives you all the instructions you need to get your projector set

up and connected to a laptop or PowerBook computer.

■Owner’s Kit folder

Includes your Quick Setup sheet, warranty brochures, CD-ROM,

and EPSON PrivateLine® Support card. Store this User’s Guide in

the folder and keep the folder with your projector at all times.

■Built-in help system

Provides assistance for common problems. Available from the

Help button on the projector or the remote control. See page 68

for details.

■support.epson.com

Download FAQs and e-mail your questions to EPSON support.

■CD-ROM

Your Owner’s Kit includes the PowerLite 600p/800p/810p

CD-ROM, which lets you register electronically and includes an

electronic copy of this book as well as a link to Presenters Online.

note

If the hand changes to an

index finger while holding

the mouse pointer over text,

ou can click to jump to a

other video device are turned off.

1. Connect the VGA end of the cable to the projector’s

Computer 2/Component Video port.

2. Connect the red, green, and blue leads at the opposite end of the

cable to the corresponding connectors on your video source.

3. If your video source has RCA audio, you can use the A/V cable to

connect to the projector’s Audio L (white) and R (red) jacks.

If your video source has a stereo mini-jack instead of RCA jacks,

you can use a stereo mini-jack cable (not included). Connect it to

the Audio 1 jack on the projector.

4. If the image doesn’t display properly, you may need to change the

Comp2/YCbCr option in the projector’s Setting menu (see

page 54).

Computer 2/

Component Video port

VGA-to-component

video cable

A/V cable

Using the Projector 19

Using the Projector

Once you’ve connected the projector to your computer or other

equipment (as described in Chapter 1 or Appendix A), you’re ready to

turn on the projector, adjust the image, and give your presentation.

Although you can operate the projector without it, the remote control

lets you use additional features. See Chapter 3 for instructions on

using the remote. This chapter covers the following:

■Turning on the projector and other equipment

■Adjusting the image

■Controlling the projector

■Shutting down the projector

20 Using the Projector

Turning On Your Equipment

Make sure your projector and other equipment are set up and

connected correctly, as described in Chapter 1 or Appendix A. Then

turn on your projector, as described below, followed by any

equipment you’ve connected to it. You can turn on your computer

and video equipment in any order, but if you have more than one

computer or video source connected, you may have to switch to the

desired source as described on page 28.

Turning On the Projector

Follow these steps to plug in and turn on the projector:

1. If you’re projecting video, first plug in and turn on your VCR,

DVD player, or other video source. (If you’re projecting from a

computer, go to step 2.)

2. Connect one end of the power cord to the power inlet on the back

of the projector.

3. Connect the other end to a grounded electrical outlet.

The P power light on top of the projector turns orange,

indicating that the projector is receiving power but not yet turned

on.

4. Remove the lens cap.

Using the Projector 21

5. Press the red Power button on top of the projector.

The power light flashes green as the projector warms up, and the

projection lamp comes on in about 30 seconds. The power light

stays green, and you may see a blue screen with the

No Signal

message displayed. This is normal.

6. Do one of the following:

■If you’re projecting from a computer, turn on or restart your

computer. In a few moments, you should see your computer

display projected.

If you see a New Hardware Wizard message saying that it has

found a plug-and-play monitor, click Cancel. If you see a

New Hardware Wizard message about USB audio, click

and follow the instructions on the screen. (Windows only)

■If you’re projecting a video, press the Play button on your

video source.

If a projected image fails to appear, see the next section for help.

Once you see your image, turn to page 24 for instructions on focusing

and making other image adjustments.

When you’re done with your presentation, shut down the projector as

described on page 29. Shutting down the projector correctly prevents

premature lamp failure and possible damage to the projector from

overheating.

Power button

power light

warning

Never look into the lens when

the lamp is on. This can

damage your eyes, and is

especially dangerous for

children.

22 Using the Projector

What To Do If You See a Blank Screen

If you see a blank screen or a blue screen with the

No Signal message

after turning on your computer or video source, try the following:

■Make sure the cables are connected correctly, as described on

page 12 (for laptops) or in Appendix A (for other systems).

■Make sure the power light is green and not flashing and the lens

cover is off.

■Try restarting your computer.

■If you’ve connected more than one computer and/or video source,

you may need to press the Computer/YCbCr or Video button on

the projector’s control panel to select the correct source. (Allow a

few seconds for the projector to sync up after pressing the button.)

If you’re using a PowerBook:

You may need to set up your system to display on the projector screen

as well as the LCD screen. Follow these steps:

1. From the Apple menu, select Control Panels, then click

Monitors and Sound.

2. Click the Arrange icon.

3. Drag one monitor icon on top of the other.

No Signal

click here

drag one monitor

icon on top of

the other

Using the Projector 23

If the Arrange option isn’t available, you may need to select one of the

Simulscan resolution settings:

1. Click the Monitor icon.

2. Select a Simulscan resolution as shown. (Allow a few seconds for

the projector to sync up after making the selection.)

If you’re using a PC laptop:

■Press the function key that lets you display on an external

monitor. It’s often labelled with an icon such as but it may

also be labelled CRT/LCD. You may have to hold down the Fn key

while pressing it. Check your laptop’s manual or online help for

details.

On most systems, the key lets you toggle between the LCD

screen and the projector, or display on both at the same time.

Allow a few seconds for the projector to sync up after pressing it.

■Depending on your computer’s video card, you might need to use

the Display utility in the Control Panel to make sure that both the

LCD screen and external monitor port are enabled. See your

computer’s documentation or online help for details.

select a

Simulscan

resolution

click here

24 Using the Projector

Adjusting the Image

Once you see your image, you’ll need to make certain adjustments:

■To focus or zoom your image, see below.

■If the image is too high or too low, you can reposition it. See

page 25.

■If the image isn’t square, see page 26.

■If only part of a computer image is displayed, you may need to

press the Resize button. See page 27 for more information.

■If the projected image is flickering or “noisy,” see page 27.

Focusing and Zooming Your Image

Rotate the focus ring to sharpen the image.

Rotate the zoom ring to reduce or enlarge the image.

focus ring

zoom ring

Using the Projector 25

If the image still isn’t large enough, you may need to move the

projector farther away from the screen. You can also use the

E-Zoom

button on the remote control to zoom in on a portion of the image.

See page 35 for instructions.

Adjusting the Height of Your Image

If the image is too low, you can raise it by extending the projector’s

foot.

1. Stand behind the projector. Press the foot release button and lift

the front of the projector. This unlocks the foot.

2. Once the image is positioned where you want it, release the

button to lock the foot in position.

3. If you need to straighten the image, rotate the round adjustable

foot at the back of the projector.

If the image is no longer square after raising it, see the next section.

foot release

button

back

adjustable

foot

26 Using the Projector

Adjusting the Image Shape

If the projected image isn’t square or has a “ ”keystone shape, do one or

more of the following:

■If your image looks like or , you’ve placed the

projector off to one side of the screen, at an angle. Move it directly

in front of the center of the screen, facing the screen squarely. If

you still can’t get a square image, press the left or right

Keystone

button on the projector’s control panel:

■If your image looks like or , press the top or bottom

Keystone button to correct the shape of the image. After

correction, your image will be slightly smaller.

You can also perform electronic keystone correction using the

projector’s Setting menu. See page 53.

Sync+

Tracking - Tracking +

Sync-

Menu Esc

Keystone

Shift

Auto

Sync+

Tracking - Tracking +

Sync-

Menu Esc

Keystone

Shift

Auto

Sync+

Tracking - Tracking +

Sync-

Menu Esc

Keystone

Shift

Auto

Sync+

Tracking - Tracking +

Sync-

Menu Esc

Keystone

Shift

Auto

Using the Projector 27

Resizing the Image

Some computer images need to be resized to display in the projector’s

native resolution. If only part of your computer image is displayed,

you can correct it with the Resize button.

■Press the Resize button on the projector’s control panel (or on

the remote control). The screen image is automatically

compressed.

■Continue pressing the Resize button to pan around the screen in

the original resolution.

If you’re projecting from video equipment, pressing the

Resize

button switches the aspect ratio between 4:3 and 16:9. If you’ve

zoomed in on your image (using the E-Zoom button on the remote),

you can press the Resize button to return it to the original display

size.

Adjusting the Tracking and Synchronization

If you’re projecting from a computer and displaying an image that

contains a lot of detail (such as the text of a letter), you may notice one

or more vertical stripes or bands, or some of the characters may look

heavy or blurred. You can increase the clarity by pressing the

Auto

button on the projector’s control panel (or the

Auto button on the

remote control). This resets the projector’s tracking, sync, and

position settings.

If further adjustment is needed, you can correct the image manually

using the Tracking and Sync buttons as described on page 76.

Resize button

Auto button

incorrect tracking incorrect sync

28 Using the Projector

Controlling the Projector

While giving your presentation, you may want to switch between

picture sources, adjust the volume, or temporarily turn off the picture

and sound. Follow the instructions below to access theses features

from your projector’s control panel. You can also access these features,

plus many others, using the remote control as described in Chapter 3.

Switching Between Picture Sources

If your projector is connected to more than one computer and/or

video source, you can use the buttons on the control panel (or remote

control) to switch between the different sources.

On the projector’s control panel, press the

Computer/YCbCr button

to switch between computer sources and component video. Press the

Video button to switch between standard (composite) video and

S-Video.

After you select a source, the screen goes dark for a moment before the

image appears.

Adjusting the Volume

If your presentation includes sound, you can adjust the volume from

the projector’s control panel. Press the

left or right side of the Volume

button.

Turning Off the Picture and Sound

You can use the A/V Mute button on the control panel to darken your

screen and turn off the sound. This is useful if you want to

temporarily re-direct your audience’s attention without the distraction

of a bright screen.

■To turn off the picture and sound, press the

A/V Mute button.

The screen goes dark.

■To turn the picture and sound back on, press the button again.

Power

Sync+

Tracking - Tracking +

Menu Esc

Help

Computer/YCbCr

Video

Auto

Source

A/V Mute

button

note

You can also have an image,

such as a company logo,

display on the screen

whenever you press the

A/V Mute button. See

page 51 for instructions.

Using the Projector 29

Shutting Down the Projector

When you’ve finished using the projector, follow the recommended

procedure to shut it down. This extends the life of the lamp and

protects the projector from possible overheating.

1. If you’ve connected a computer or laptop and it’s displaying only

through the projector (the computer’s monitor is disconnected or

turned off), shut down the computer first; otherwise you may not

be able to see your computer’s display to shut it down properly.

2. To turn off the projector, press the red Power button on the

projector or remote control.

You see a confirmation message. (If you don’t want to turn it off,

press any other button.)

3. Press the Power button again. The power light flashes orange for

about a minute as the projector cools down. When the projector

has cooled, the orange light stays on and the exhaust fan shuts off.

If you want to turn the projector on again, wait until the orange

light stops flashing. Then press the

Power button.

4. If you extended the front foot, press the foot adjust button to

retract it.

5. Replace the lens cap and unplug the power cord.

6. If you’re using a VCR or other video source, turn it off after you

turn off the projector.

7. Disconnect all equipment, and store the projector in a protective

case.

note

When the projector has not

received any input signals for

30 minutes, it automatically

turns off the projector lamp

and enters “sleep mode.” This

conserves electricity, cools the

projector, and extends the life

of the lamp. If you are done

using the projector, unplug

the power cord. If you want

to start projecting again, press

the Power button.

Power button

power light

caution

To avoid damaging the

projector or lamp, never

unplug the power cord when

the power light is green or

flashing orange.

30 Using the Projector

Using the Remote Control 31

Using the Remote Control

The remote control lets you access your projector’s features from

anywhere in the room—up to 30 feet away. You can use it to turn

the projector on and off, zoom in on a portion of your image, and

highlight your presentation.

If you’re using a computer and you’ve connected the mouse cable (as

described in Chapter 1 or Appendix A), you can use the remote

control as a wireless mouse.

This chapter covers the following information:

■Turning on and using the remote control

■Controlling the picture and sound

■Highlighting your presentation

■Using the remote control as a wireless mouse

32 Using the Remote Control

Turning On and Using the Remote

Control

Before using the remote control, you need to install its batteries and

turn it on as described below.

Installing Batteries

Follow these steps to install or replace the batteries:

1. Press the tab to release the

battery compartment cover.

2. Remove the cover and insert

the two AA batteries included

with the projector as shown.

3. Replace the battery

compartment cover.

Turning On the Remote Control

Make sure batteries are installed. Then push up the on/off switch on

the side of the remote control to turn it on.

Turn off the remote control before transporting it or storing it in a

projector case. This prevents the batteries from discharging if

something presses against one of the buttons.

caution

When replacing batteries,

take the following

recautions:

■Don’t mix old and new

batteries.

■Replace batteries as soon as

they run out. If the batteries

leak, wipe away battery fluid

with a soft cloth. If fluid gets

on your hands, wash them

immediately.

■Do not expose batteries to

heat or flame.

■Dispose of used batteries

according to local regulations.

■Remove batteries if you

won’t be using the projector

or a long period of time.

tab

Using the Remote Control 33

Using the Remote Control

When using the remote control, stand within 30 feet of the projector.

Point the remote control either at the front or back of the projector or

at the screen (the projector’s front sensor can detect signals bounced

off the screen).

■Press the button for the function you want to use. See the

following pages for instructions.

■For some functions, you need to use the button like a mouse to

navigate on the screen. Press the edge of the button with your

thumb—or grasp it between your thumb and finger and tilt it in

the direction you want to move.

Controlling the Picture and Sound

You can use the remote control to select your source, adjust the

volume, temporarily turn off the picture and sound, freeze the action,

zoom in on the picture, or display a picture-in-picture video image.

Make sure you have set up your projector and connected any

equipment as described in Chapter 1 or Appendix A.

Switching Between Picture Sources

If you’ve connected your projector to a computer and/or video

sources, you can use the buttons on the remote control to switch

between the different sources.

■Press the Comp2/YCbCr button to select a computer or video

source connected to the Computer 2/Component Video port on

the projector.

■Press the Comp 1 button to select a computer connected to the

DVI Computer 1 port on the projector.

■Press the Video button to select a composite video source.

■Press the S-Video button to select an S-video source.

After you select a source, the screen goes dark for a moment before the

image appears.

Comp1

Source

Video

Auto

PresetP in P

S-Video

Resize

Comp2/YCbCr

Help

34 Using the Remote Control

Adjusting the Volume

If you’ve connected an audio source to the projector, you can adjust

the sound that’s output through the projector’s speakers.

■To increase the volume, press on the right side of the

Volume

button.

■To reduce the volume, press on the left side of the

Volume

button.

Turning Off the Picture and Sound

You can use the

A/V Mute button on the remote control to turn off

the image and sound and darken your screen. This is useful if you

want to temporarily re-direct your audience’s attention without the

distraction of a bright screen.

■To turn off the picture, press the

A/V Mute button. The screen

goes dark.

■To turn the image back on, press the button again.

You can also have an image, such as a company logo, display on the

screen whenever you press the

A/V Mute button. See page 51 for

instructions.

Stopping Action

You can use the remote control to stop the action in your video or

computer image.

■Press the

Freeze button to stop the action and keep the current

image on the screen. The sound will continue.

■Press the

Freeze button again to re-start it.

Power

A/V Mute Freeze

E-Zoom

Power

A/V Mute Freeze

E-Zoom

Using the Remote Control35

Zooming Your Image

You can zoom in on a portion of the image using the

E-Zoom button

on the remote control.

1. Press the

E-Zoom button.

A crosshair indicating the center of the zoom-in area appears on

the screen.

2. Use the button to move the crosshair where you want it.

3. Press the right side of the

E-Zoom button to enlarge the selected

area.

■Press the button repeatedly to enlarge it up to four times in

25 steps.

■Press and hold the button to zoom in to the size you want.

■You can use the button to scroll around the image.

4. Press the left side of the

E-Zoom button to zoom out. You can

also press the

Resize or Esc button to return to the original size.

Resizing the Image

Some computer images need to be resized to display in the projector’s

native format—1024 × 768 pixels. If only part of your computer

image is displayed, you can correct it with the

Resize button.

■Press the

Resize button on the remote control (or on the

projector’s control panel). The screen image is automatically

compressed.

■Continue pressing the

Resize button to pan around the screen in

the original resolution.

If you’re projecting from video equipment, pressing the

Resize

button switches the aspect ratio between 4:3 and 16:9. If you’ve

zoomed in on your image (using the

E-Zoom button on the remote),

you can press the

Resize button to return it to the original display

size.

Power

A/V Mute Freeze

E-Zoom

36 Using the Remote Control

Displaying Picture-in-Picture Video

You can open a small video window on your computer image, and

view a video at the same time as your computer presentation. If you’re

using component video, you can display a second video (from a

composite or S-video source) in the window.

First make sure you have connected your VCR or other video sources

as described in Chapter 1. If you’re using S-video, you need to select it

in the P in P menu option as described on page 53.

1. Press the

P in P button on the remote control. The screen may go

dark for a moment, and then your video image appears in a small

window on the screen. A menu appears in the lower left corner of

the screen, describing how to move and resize the image.

2. Use the button to reposition the video window on the screen.

You can use the

E-Zoom button to enlarge or reduce the video

window.

3. When the window is located and sized the way you want, press

the button. The menu disappears, and your video plays on the

screen.

4. When you’re finished viewing the picture-in-picture, press the

P in P button again. The video window disappears.

video window

Using the Remote Control37

Highlighting Your Presentation

You can highlight areas on the screen using the numbered buttons on

the remote control. You can use these “special effects” features to

annotate your presentation slides or call attention to your most

important points. The following three highlighting tools are available:

■Pointer or cursor stamp (button

■Spotlight (button 2)

■Bar (button 3)

You can customize the highlighting tools through the Effect menu.

See page 50 for instructions.

Using the Pointer

You can choose from three types of pointers and place them anywhere

on your screen.

1. To activate the pointer tool, press button

1 on the remote control.

A pointing hand appears in the center of the screen. To change it

to an arrow, press

1 again. Press

1 a third time to see a different

arrow.

2. Press the side of the button (or grasp it between your thumb

and finger) to move the arrow wherever you want it.

3. To “paste” the pointer on the screen, press down in the center of

the button. You can then continue to work with another

pointer, moving it around the screen or pasting it wherever you

want.

4. To erase the pointer(s) pasted on the screen and cancel the effect,

press

Esc .

Power

A/V Mute Freeze

E-Zoom

pointer

spot-

light

bar

note

You can use the projector’s

Effect menu to select different

pointers. See page 50.

38 Using the Remote Control

Spotlighting Your Image

With the Spotlight tool, you can highlight part of the screen.

1. To activate the spotlight tool, press button

2 on the remote

control. A square spotlight appears on the image.

You can continue pressing button

3 to switch between three

spotlight sizes.

2. Use the button to move the spotlight where you want it.

3. To remove the spotlight, press

Esc .

You can change the default size of the spotlight using the Effect menu;

see page 50.

Using Horizontal and Vertical Highlights

With the bar tool, you can draw bold horizontal or vertical lines on

the screen to underline or highlight your presentation points. You can

choose from three types of bars.

1. To activate the bar tool, press button

3 on the remote control. A

horizontal bar appears across the screen. If you want a vertical bar,

press

3 again. If you want to try another horizontal bar, press

again.

2. Use the button to move the bar up and down the screen (or left

and right if you are using the vertical bar).

3. To cancel the bar drawing feature, press

Esc .

note

You can change the color

and width of the bars

using the Effect menu.

See page 50.

Using the Remote Control39

Using the Remote Control as a

Wireless Mouse

When you use the remote control as a wireless mouse, you can control

your computer or click through slideshow-style presentations (such as

PowerPoint) from up to 30 feet away. This gives you more flexibility,

since you won’t need to stand near your computer to change slides, for

example.

To control your computer with the remote, make sure you have

connected the mouse cable between the projector and your computer

as described on page 13 (for laptops) or in Appendix A (for other

systems).

■To move the mouse pointer on the screen, aim the remote at the

screen and press on the edge of the button with your thumb—

or grasp it between your thumb and finger and tilt it in the

direction you want to move. This button works like the mouse

button on many laptop keyboards.

■To click (or left-click), press the left mouse button below the

button. Or, press down on the center of the button. This

changes slides in a PowerPoint presentation in Slide Show mode.

■To right-click, press the

Esc button.

Power

A/V Mute Freeze

E-Zoom

Esc

Comp1

Source

Video

Auto

Preset

Volume

P in P

S-Video

Resize

Comp2/YCbCr

Help

Power

A/V Mute Freeze

E-Zoom

Esc

Comp1

Source

Video

Auto

Preset

Volume

P in P

S-Video

Resize

Comp2/YCbCr

Help

To left-click, press the

left mouse button

To right-click,

press Esc

Power

A/V Mute Freeze

E-Zoom

Esc

Comp1

Source

Video

Auto

Preset

Volume

P in P

S-Video

Resize

Comp2/YCbCr

Help

Use the button to

move the mouse pointer

40 Using the Remote Control

■To double-click, press down twice on the left mouse button.

■To click and drag, press down on the left mouse button and then

tilt the button in the direction you want to drag.

You can use the up and down arrow buttons on the remote control to

move the cursor or move through a PowerPoint presentation.

■Press the down arrow to move forward through a presentation or

display the next slide.

■Press the up arrow to move backward or display the previous slide.

Power

A/V Mute Freeze

E-Zoom

Fine-tuning the Projector 41

Fine-tuning the Projector

You can use the projector’s on-screen menus to adjust the image,

sound, and other features. You can also create your own startup

screen, customize the highlighting tools, and find out how long your

lamp has been in use. This chapter covers the following information:

■Using the menu system

■Adjusting the image

■Adjusting the sound

■Customizing the highlighting controls

■Creating your own startup screen

■Customizing projector features

■Viewing lamp usage and other information

■Restoring the default settings

42 Fine-tuning the Projector

Using the Projector’s Menu System

The eight projector menus let you adjust and customize the projector

features from either the control panel or remote control:

■The Video menu controls the look and quality of the projected

image. It lets you adjust the image position and fine-tune settings

such as Brightness, Sharpness, and Contrast.

■The Audio menu controls the volume level, treble, and bass

settings.

■The Effect menu lets you change the cursor speed and modify the

highlighting tools available on the remote control.

■The Setting menu allows you to set or adjust features such as the

Picture in Picture (P in P) video source, blank screen color,

A/V Mute display option, and sleep mode.

■The User’s Logo menu lets you capture and store a custom image

or logo which you can then use as a startup screen or with the

A/V Mute option.

■The Advanced menu lets you specify additional projector settings,

including menu language, startup screen, color setting, and rear or

ceiling projection.

■The About menu provides information about lamp status and

computer or video settings.

■The Reset All menu lets you restore the factory defaults for all the

projector settings.

Fine-tuning the Projector 43

Changing Menu Settings

You can use the buttons on the control panel or remote control to

access the menus and change settings. Follow these steps:

1. To display the menu screen, press the

Menu button on the

control panel or the remote control.

You see the menu screen:

The eight menus are listed on the left, and the options available

for the highlighted menu are shown on the right.

2. Press the

Sync+ or Sync– button on the control panel,

or press up or down on the button on the remote control, to

scroll through the menu list.

Esc

Comp1

Source

Video S-Video

Comp2/YCbCr

Help

Sync+

Tracking - Tracking +

Menu Esc

Computer/YCbCr

Video

Auto

Source

control panel remote control

menus

menu options

44 Fine-tuning the Projector

3. When the menu you want is highlighted, press the button on

the control panel or the remote control to select it. The highlight

moves to the first option for that menu.

4. Use the

Sync+ or Sync– button (control panel) or the

button (remote control) to scroll through the list of options. (If

a computer or video source isn’t connected, certain options may

be unavailable.)

5. Use the

Tracking– or Tracking+ button (control panel) or

the button (remote control) to change the setting for the

selected option.

Enabled settings are indicated by a green light, while disabled

ones are blank.

6. Press the

Esc button to return to the main menu. Your changes

are saved automatically.

7. Press

Esc again (or the

Menu button) to exit the menu system.

note

If you want to go back to the

default settings on any menu,

select

Reset , press , select

Yes , and then press .

Fine-tuning the Projector 45

Adjusting the Image

The Video menu lets you make adjustments to the projected image.

The options available in the menu depend on which source is

connected to the projector: standard computer video (analog RGB),

DVI computer video (digital RGB), composite or S-Video,

component video, or RGB video (standard TV).

Video menu for standard computer display

(Analog-RGB)

Video menu for DVI computer display

(Digital-RGB)

Video menu for composite video or S-Video

Video menu for component video Video menu for RGB-Video

46 Fine-tuning the Projector

Repositioning the Image

Follow these steps to move the image to a different position:

1. Press the

Menu button. You see the menu screen.

2. Press the button to select the Video menu.

3. Press to select the

Position option. You see a positioning

screen.

4. Use the Tracking and Sync buttons (control panel) or the

button (remote control) to move the image left, right, up, or

down.

5. When the image is positioned the way you want, press

Esc to exit.

Adjusting Image Appearance

Follow these steps to adjust the appearance of your image:

1. Press the

Menu button. You see the menu screen.

2. Press the button to select the Video menu.

3. Use the Tracking and Sync buttons (control panel) or the

button (remote control) to set the following options:

■Tracking (analog computer images only)

Removes unwanted vertical lines from a computer image by

matching the projector’s internal clock to the computer

display signal.

■Sync (analog computer images only)

Corrects fuzziness by synchronizing the projector with the

tracking signal sent from the computer.

■Brightness

Lightens or darkens the overall image.

■Contrast

Adjusts the difference between light and dark areas. When

Auto is selected (the default), the projector performs gain

adjustment periodically.

■Color (video only)

Adjusts the color depth or intensity of the image.

note

If you have repositioned the

image or adjusted the sync

setting, you can use the

button on the control panel

or the Auto button on the

remote control to restore the

default settings.

Fine-tuning the Projector 47

■Tint (NTSC video only)

Adjusts the balance of green to magenta in the image.

■Sharpness

Adjusts the sharpness of the image.

■Color Mode

Corrects the vividness of image color. You can select from the

following six settings, and save a different one for each

computer and/or video source:

sRGB : To use the sRGB standard for computer displays (the

default when projecting from a computer with analog video)

High Brightness: For presentations in bright rooms

Meeting: For projecting without color enhancement

Presentation: For presentations in dark rooms

Theater: For optimizing movie images with natural color

(the default for video or S-video display)

Amusement: For optimizing games

■Resolution (analog computer images only)

Leave this setting at

Auto to allow the projector to detect the

video signal automatically. If the projector is unable to sync

up with the computer, select

Manual and choose one of the

settings.

■Video Signal (video only)

Leave this setting at

Auto unless you are using a 60-hertz PAL

system (select

PAL60 ).

■Noise Reduction (video only)

Reduces visual “ ”noise. This is especially useful when text and

video images are combined, as in movies with subtitles.

4. When the image is set correctly, press

Esc or Menu . Your settings

are automatically saved.

48 Fine-tuning the Projector

Saving and Recalling Computer Settings

When you are projecting from an analog computer source, you can

save and recall settings (resolution, tracking, sync signal, and position)

in up to five different combinations. This is useful if you use more

than one computer with the projector; you can save the settings for

each one and recall them when necessary. Follow these steps to save

the projector’s current settings:

1. Press the

Menu button to display the Main menu.

2. Press the button to select the Video menu.

3. Use the

Sync– button (control panel) or the button

(remote control) to move down to the

Preset option.

4. Press . You see the Preset Selection menu with the current

resolution setting displayed.

5. Use the

Sync– button (control panel) or the button

(remote control) to select the number to which you want to assign

the current settings.

6. Press . If you see an

Overwrite? prompt, select

Yes and

press .

7. Press

Esc or Menu to exit.

When you want to use a saved setting, press the

Preset button on the

remote control. You see the selected setting displayed on the screen.

To select another number, press the

Preset button again until the

setting number you want is displayed. The projector resets itself

according to the selected setting.

Fine-tuning the Projector 49

Adjusting the Sound

You can use the Audio menu to select the audio source or adjust the

sound volume or treble/bass balance.

1. Press the

Menu button. You see the menu screen.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight

Audio . You see the following:

3. Press to select the Audio menu.

4. Use the Tracking and Sync buttons (control panel) or

the button (remote control) to set the following options:

■Audio Input

Audio 1 is automatically selected for computer sound, and

Audio2 for video. Select

USB to amplify computer sound

through a USB cable connected to the projector.

■Volume

■Treble

■Bass

5. When you’re finished adjusting the sound, press

Esc or Menu .

50 Fine-tuning the Projector

Customizing the Highlighting Tools

The highlighting tools let you add pointers and other types of

annotations to your image, as described on pages 37 to 39. You can

use the Effect menu to customize these tools and set the pointer speed

for highlighting. The

Reset option lets you return all the highlighting

tools to their default settings.

1. Press the

Menu button. You see the main menu.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight

Effect . You see the Effect menu:

3. Press to select the Effect menu.

4. Use the Tracking and Sync buttons (control panel) or the

button (remote control) to customize the following:

■Pointer/Stamp

Lets you define the shape and size for three different pointers.

■Spotlight

Lets you choose a large, medium, or small spotlight.

■Bar

Lets you define three different bars. For each one, you can set

the color and width, and choose between vertical and

horizontal.

■Pointer speed

Lets you choose low, medium, or high speed.

Fine-tuning the Projector 51

5. When you’re finished customizing the highlighting tools, press

Esc . Your selections are saved.

Creating Your Own Startup Screen

You can transfer any image from your computer or video source to the

projector, and then use it as your startup screen. You can also use it as

the screen displayed when the projector is not receiving a signal or

when you press the

A/V Mute button. The image can be a company

logo, slogan, photograph, or any other image you want to use.

Capturing the Image

Start by displaying the image you want to use. It can be an image from

either a computer or video source such as a DVD player or digital

camera. Then follow these steps to capture the image and transfer it to

the projector:

1. Press the

Menu button on the control panel or remote control.

You see the menu screen.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight the

User’s Logo menu, then

press .

3. When you see the screen shown at right, select

Yes and press .

A selection box displays over the image.

User's Logo Capture

Do you use the present image

as a user's logo?

Yes No

:Select:Return :Execute

52 Fine-tuning the Projector

4. Use the Tracking and Sync buttons (control panel) or the

button (remote control) to select the area of the image you want

to use. Then press .

5. When you see the message “Do you use this image?” select

Yes

and press .

You see the screen shown at the left.

6. Use the Tracking and Sync buttons (control panel) or

the button (remote control) to select a zoom rate (display

size), and then press .

7. When the message “Do you save the user’s logo?” appears, select

Yes and press .

Saving the logo may take a few moments. Do not use your

projector or video source (computer, DVD player, etc.) while the

logo is being saved.

8. When you see the message “Saving the user’s logo is completed,”

press

Esc to return to the menu screen.

Choosing When to Display the Image

After your image is saved, you can set it up as the no-signal message

and/or the screen that’s displayed when you press

A/V Mute .

1. Press the

Menu button to display the menu screen (if not already

displayed).

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight the

Setting menu.

3. Press the button to select the Setting menu.

4. Use the

Sync– button (control panel) or the button

(remote control) to highlight either

No-Signal Msg . or A/V

Mute , depending on when you want the image to display.

5. Use the Tracking+ button (control panel) or the button

(remote control) to select

Logo . This sets your image as the screen

to be displayed.

6. When you’re finished, press

Esc or Menu to exit.

User's Logo Capture

Set the zoom rate.

zoom rate :

:Select:Return :Execute

100 200 300

note

You can also set up your

image as the startup screen

using the Advanced menu; see

age 55.

Fine-tuning the Projector 53

Customizing Projector Features

You can use the Setting menu to disable the projector’s sleep mode,

adjust the image shape, and customize several other features.

1. Press the

Menu button.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight

Setting . You see the options and

their settings on the right side:

3. Press to select the Setting menu.

4. Use the Tracking and Sync buttons (control panel) or

the button (remote control) to set the following options:

■V-Keystone or H-Keystone

Correct the shape of the image. Keystone correction makes

the image smaller, especially if you use both vertical

(V-Keystone ) and horizontal (

H-Keystone ) correction. If

you need to adjust the shape in both directions, adjust the

vertical first. If the image looks uneven after you adjust the

shape, decrease the Sharpness setting (see page 47).

■P in P

Selects the source used by the picture-in-picture display

(standard composite video or S-video).

54 Fine-tuning the Projector

■No-Signal Msg.

Selects a screen color or image to display when the projector is

not receiving a signal. The logo setting displays an image that

you have transferred to the projector (see page 51).

■Prompt

Turns off the identifying text that appears briefly when you

switch picture sources. (It’s best to leave this on.)

■A/V Mute

Selects the screen color or image to display when you press

the A/V Mute button. The logo setting displays an image that

you have transferred to the projector (see page 51).

■Comp1 Input

Specifies the format for input to the

Computer1 port. Select

Digital-RGB/Analog-RGB , Analog-RGB , or RGB-Video.

■Comp2/YCbCr Input

Specifies the format for input to the

Computer 2/

Component Video port. If the source is a computer, select

Analog-RGB. If the source is a video device, select

YCbCr for

DVD images

or YPbPr for progressive scan DVD or HDTV

images.

■Sleep mode

When sleep mode is on, the projector turns off the lamp if it

has not received any input signals for 30 minutes. Turn sleep

mode off if you want the lamp to remain on all the time.

5. When you’re finished, press

Esc or Menu .

Fine-tuning the Projector 55

Setting Advanced Features

You can use the Advanced menu to configure the projector for rear

projection or ceiling mounting, and adjust several other features.

1. Press the

Menu button.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight

Advanced . You see the features and

their settings on the right side:

3. Press to select the Advanced menu.

4. Use the Tracking and Sync buttons (control panel) or

the button (remote control) to set the following options:

■Language

Select from 9 languages to be used for the projector menus.

■Startup Screen

Turn on to display your captured image or logo whenever the

projector starts. (See page 51 for more information.)

■Color Adjustment

Adjusts the color temperature of the projected image. Select

Color Temp. to set a temperature between 5000 and

10000 K. Select

RGB to adjust individual red, green, and

blue values, as shown. (Not available if

sRGB is selected as

the Color Mode setting in the Video menu. See page 47 for

more information.)

■Rear Proj.

Turn on to project from behind onto a transparent screen.

56 Fine-tuning the Projector

■Ceiling

Turn on when the projector is mounted upside-down from

the ceiling.

■COM Port

Switches between serial (

RS-232C ) and USB communication

for programming/projector control.

5. When you’re finished, press

Esc or Menu .

Viewing Lamp Usage and Other

Information

Use the About menu to view information about the display settings of

your computer and the number of hours the lamp has been used.

1. Press the

Menu button. You see the main menu.

2. Use the

Sync– button (control panel) or the button

(remote control) to highlight

About .

You see the lamp usage hours and computer display settings on

the right:

The life span of the lamp is about 1500 hours. If the number

shown is close to 1500, make sure you have a spare lamp handy.

After you change the lamp, you need to reset the lamp timer.

note

If you access the About menu

when the projector display is

set to video, you see only the

lamp life and the video signal

setting.

note

The lamp usage timer doesn’t

lamp for at least 10 hours.

Fine-tuning the Projector 57

3. If you have changed the lamp, press to select

Reset Lamp

Timer. Press again, then select

Yes when you see the prompt.

Press to confirm the reset.

4. When you’re finished, press

Esc or Menu .

Restoring the Default Settings

The Reset All option lets you return all the projector settings to their

default values.

Select

Reset All and press the button on the control panel or

remote control to display the confirmation screen. Select

Yes to reset

all the default settings or

No to cancel.

58 Fine-tuning the Projector

60 Maintaining and Transporting the Projector

Cleaning the Lens

Clean the lenses whenever you notice dirt or dust on the surface.

■Use a canister of compressed air to remove dust.

■To remove dirt or smears on the lenses, use lens-cleaning paper. If

necessary, moisten a soft cloth with lens cleaner and gently wipe

the lens surface.

Cleaning the Projector Case

Before you clean the case, first turn off the projector and unplug the

power cord.

■To remove dirt or dust, wipe the case with a soft, dry, lint-free

cloth.

■To remove stubborn dirt or stains, moisten a soft cloth with water

and a neutral detergent. Then wipe the case.

■Do not use wax, alcohol, benzene, thinner, or other chemical

detergents. These can damage the case.

Remove the cap

before cleaning

64 Maintaining and Transporting the Projector

5. Grasp the lamp as shown and pull it straight out.

6. Gently insert the new lamp.

7. Once the lamp is fully inserted, tighten its screws.

8. To replace the lamp cover, insert the tabs and then snap the cover

into place. (The projector won’t come on if the lamp cover is

loose.)

caution

Do not touch the glass

ortion of the lamp assembly.

Touching the glass could

result in premature lamp

ailure.

Maintaining and Transporting the Projector65

Resetting the Lamp Timer

After you replace the lamp, you need to reset the lamp timer using the

projector’s menu.

1. Press the

Menu button on the control panel or the remote

control. You see the main menu.

2. Use the Sync– button (control panel) or the button (remote

control) to highlight

About .

You see the lamp usage hours and other settings.

3. Press to select

Reset Lamp Timer. Press again. You see this

prompt:

4. Select

Yes , then press .

5. When you’re finished, press

Esc or Menu .

66 Maintaining and Transporting the Projector

Transporting the Projector

The projector contains many glass and precision parts. If you need to

transport it, follow these packing guidelines to prevent damage

to the projector:

■When shipping the projector for repairs, use the original

packaging material if possible. If you do not have the original

packaging, use equivalent materials, placing plenty of cushioning

around the projector.

■When transporting the projector a long distance, first put it in a

carrying case (such as an optional EPSON case), then pack it in a

firm box, using cushioning around the case.

■If you want to store the remote control inside the projector’s

carrying case, be sure to turn it off using the switch on its side.

This prevents the batteries from discharging if something presses

against one of the buttons.

■When you are hand-carrying the projector, use the carrying

handle.

note

EPSON shall not be liable

or any damages incurred

during transportation.

carrying handle

Solving Problems67

Solving Problems

This chapter helps you solve problems with your projector, and tells

you how to contact technical support for problems you can t solve ’

yourself. This chapter explains the following:

■Using the projector’s on-screen help system

■What to do when the projector’s status lights flash

■Solving problems with the image or sound

■Solving problems with the remote control

■Contacting technical support

68 Solving Problems

Using On-Screen Help

If the image doesn’ ’t look right or your audio isn t working, you can

get help by pressing the blue

? Help button on top of the projector or

on the remote control. The following choices are available:

■Help for the image

■Help for the sound

■Language selection (Language)

Follow these steps to get help:

1. Press the blue

? Help button on the projector or the remote

control.

You see the Help menu:

2. Press the

Sync+ or Sync– button on the projector (or

use the button on the remote control) to highlight one of the

options. Then press the button to select it.

3. Press the

Tracking– or Tracking+ button on the projector

(or use the button on the remote control) to highlight the

problem you want to solve. Then press the button to view the

solution(s).

Esc

Comp1

Source

Video S-Video

Comp2/YCbCr

Help

Power

Menu Esc

Help

Computer/YCbCr

Video

control panel remote control

doesn't

doesn'tdoesn't

Solving Problems 69

4. Highlight a solution (if this choice is available). Then press the

button to select the solution.

Press the

Esc button if you need to back up.

If the solution is to adjust one of the settings, press either

the Tracking– or Tracking+ button on the projector (or

use the button on the remote control) to adjust it.

5. To exit the Help system, press the blue

? Help button.

If none of the suggestions solves your problem, see additional

solutions to problems in the following sections.

What To Do When the Lights Flash

The lights on top of the projector indicate the projector’s status and

let you know when a problem occurs.

If the projector is not working correctly, first turn it off, let it cool,

and unplug it. Then plug the power cord back in and turn on the

projector. If this does not solve the problem, check the status lights on

top of the projector and try the solutions recommended on the

following pages.

power light lamp light temperature

light

70 Solving Problems

The power light is flashing orange and you cannot turn

on the projector.

The lamp is cooling down. Wait until the light turns off and then

press the

Power button to turn on the projector.

The power light does not come on.

Make sure the power cord is connected securely both at the power

outlet and the projector. If you have just replaced the lamp, make sure

the cover is securely fastened.

The lamp warning light is red or flashing red.

Replace the lamp as described on page 62.

The lamp warning light is flashing orange.

The lamp is almost burned out. Make sure you have a replacement

lamp ready.

The temperature light is flashing orange.

■The projector is too hot, and is in a high-speed cooling cycle.

Make sure the room temperature does not exceed 95 °F (35 °C)

and there is plenty of space around and under the projector for

ventilation.

■The air filter may be clogged. Clean or replace it as described on

page 61.

The temperature light is red.

■The projector is overheating, which turns the lamp off

automatically. Wait until the cooling fan stops, then unplug the

power cord. Plug the power cord back in and press the

Power

button. Make sure the room temperature is not above 95 °F

(35 °C) and there is plenty of space around and under the

projector for ventilation.

■The air filter may be clogged. Clean or replace it as described on

page 61.

warning

Except as specifically

explained in this

User’s Guide, do not

attempt to service this

product yourself.

Solving Problems 71

■If the projector continues to overheat after you clean the air filter,

the problem may be caused by damage to the cooling fan or

temperature sensor. Contact EPSON for help.

Refer to the following table for a complete description of the

projector’s status lights and their meaning:

Status lights

Light Status Description

orange The projector is in sleep mode. You can unplug it or press the Power

button to turn it on.

flashing green The projector is warming up. Wait for the image to appear.

green The projector is operating normally.

flashing orange The projector is cooling down. You can’t turn it back on (and you

should not unplug it) until the light stops flashing and remains orange.

flashing red Power is cut off because of an internal problem. Remove the power

cord and contact EPSON for help.

red The lamp is burned out. Replace it as described on page 62.

flashing orange The lamp is almost burned out. Make sure you have a replacement

lamp ready.

flashing red There is a problem with the lamp, power supply, fan, or circuit. If

necessary, replace the lamp as described on page 62.

flashing orange The projector is too hot. Make sure the temperature surrounding the

projector does not exceed 95 °F (35 °C) and there is plenty of space

around and under the projector for ventilation. Clean the air filter if

necessary. See page 61 for instructions.

red The projector is overheating, which turns off the lamp automatically.

Let it cool for a few minutes, then turn it back on. Make sure there is

plenty of space around and under the projector for ventilation. If it

continues to overheat, you may need to change the air filter. See

page 61 for instructions.

flashing red There is a problem with the cooling fan or temperature sensor. Turn

off the projector and unplug it. Contact EPSON for help.

72 Solving Problems

Solving Problems with the

Image or Sound

No image appears on the screen.

■Check that the P power light is green, not flashing, and the lens

cap is off.

■The projector may be in sleep mode. If the

P power light is

orange, press the

Power button to turn the projector on.

■If the power was switched off and then on again, the projector

may still be cooling down. Wait until the power light stops

flashing and remains orange; then press the

Power button again.

■Try pressing the

Power button on the remote control.

■Make sure the

Brightness setting on the Video menu is correct.

See page 46 for more information. Try selecting the

Reset All

setting to return all setup menus to their default values.

■Press the

A/V Mute button to make sure the picture has not been

turned off temporarily.

■The attached computer may be in sleep mode or displaying a

black screen saver. Try pressing a key on the computer.

You see a blue screen with the message No Signal displayed.

■Make sure the cables are connected correctly, as described in

Chapter 1.

■Try restarting your computer.

■If you’ve connected a computer and one or more video sources,

you may need to press the

Computer/YCbCr or Video button

(on the projector) or the

Comp1 , Comp2/YCbCr , Video , or

S-Video button (on the remote control) to select the correct

source. Allow a few seconds for the projector to sync up after

pressing the button.

Solving Problems75

The image contains static or noise.

■Make sure the

Comp1 Input and Comp2/ YCbCr options in the

Setting menu are correct. See page 54.

■If you’re using a computer cable longer than 6 feet (2 meters), or

an extension cable, the image quality may be reduced.

■Keep your computer and video cables away from the power cord

as much as possible to prevent interference.

■The video signal may be split between the computer and the

projector. If you notice a decline in the projected image quality

when the image is displayed simultaneously on your laptop

computer and the projector, turn off the laptop’s LCD display.

The image is blurry.

■There may be dirt or smears on the lens. Clean the lens as

described on page 60.

■Adjust the focus using the focus ring.

■Make sure the lens is not fogged by condensation. You may need

to wait before using the projector after moving it from a cold

environment to a warm environment.

■Adjust the

Sharpness setting on the Video menu (see page 46).

When you change video settings, you should be able to see the

effect on the screen immediately. If you’re projecting from a

computer, you may also need to adjust the tracking and sync as

described in the next section. If you don’t like the new settings,

you can always select

Reset to return to the factory default

settings.

76 Solving Problems

You see vertical stripes or the image still looks blurry after

trying the solutions in the previous section.

■If you’re projecting from a computer and displaying an image that

contains a lot of fine detail, you may notice one or more vertical

stripes or bands, or some of the characters may look heavy or

blurred. Press the button on the projector or the

Auto button

on the remote control. This resets the projector’s tracking and

sync settings.

■If further adjustment is needed, you can fine-tune the

Tracking

and Sync settings manually using the buttons on the projector’s

control panel (or using the Video menu as described on page 46).

1. Fill the screen with an image containing fine detail when

making these adjustments. For example, in Windows you can

select a pattern to appear as your desktop background. If this

option isn’t available, try projecting black text on a white

background.

2. Hold down the Shift button and press the Tracking– or

Tracking+ buttons to eliminate vertical stripes.

(If you don’t see any changes on screen while pressing the

buttons, select

Reset All in the projector’s menu system as

described on page 56; then repeat the tracking adjustment.)

3. Hold down the Shift button and press the

Sync– and Sync+

buttons to increase the sharpness of the image.

R i

Tracking - Tracking +

Sync-

Keystone

Shift

Auto

R i

Sync+

Tracking - Tracking +

Sync-

Keystone

Shift

Auto

Solving Problems 77

The colors of the image are not right.

■If you’re displaying a computer image, use the

Color Mode

option in the projector’s Video menu to adjust the color. If you’re

displaying video, adjust the

Color , Tint , and Color Mode

settings on the Video menu.

■Try changing the Color Adjustment setting on the Advanced

menu.

■Check your computer display settings to correct the color balance.

There is no sound.

■Try turning up the volume. Press the right side of the

Volume

button on the remote control or the projector’s control panel.

■If you’re using a VCR or other video source, make sure the

volume is not turned all the way down or muted. Also, make sure

the cables are connected correctly, as described in Chapter 1.

■If your presentation includes computer audio, make sure the

volume control on your computer is not turned all the way down

or muted. Make sure the USB cable is securely connected to the

projector and your computer, and the drivers are installed. If

you’re using the audio cable, make sure it is securely connected to

both the projector and your computer’s headphone jack or

audio out jack. See page 14 (for laptops) or Appendix A (for other

systems).

■Make sure the Windows volume controls on your computer are

not turned all the way down or set to Mute. You may be able to

check this by clicking the volume control in your Windows

System Tray (lower right corner of the screen).

■Make sure the

A/V Mute button is not enabled.

■The wrong source may be selected. Press the

Computer/YCbCr

or Video button on the projector—or the Comp1,

Comp2/YCbCr , Video , or S-Video button on the remote

control—to select the correct source.

note

Because of the different

technologies used, your

projected image may not

exactly match the colors on

your laptop or computer

monitor.

78 Solving Problems

Solving Problems with the Remote

Control

The projector doesn’t respond to remote control commands.

■Make sure the remote control is turned on.

■Make sure you are within 30 feet (9 meters) of the projector, and

within range of the projector’s front or back sensor

(approximately 30° to left or right and 15° above or below).

■The remote control batteries may not be installed correctly or may

be low on power. To change the batteries, see page 32.

■Dim the room lights and turn off any fluorescents. Make sure the

projector is not in direct sunlight. Strong lighting, especially

fluorescent lights, may affect the projector’s infrared receivers.

■Turn off any nearby equipment that emits infrared energy, such

as a radiant room heater.

You can’t control the mouse pointer with the remote

control.

Make sure the cable is securely connected to both your computer’s

mouse or USB port and the projector’s mouse or USB port. For

details, see page 13 (for laptops) or Appendix A (for other systems).

on/off

switch

Solving Problems 79

Where To Get Help

EPSON provides technical assistance through electronic support

services and automated telephone services 24 hours a day, as listed in

the following table.

Telephone Support Services

To use the EPSON PrivateLine Support service, call (800) 637-7661

and enter the PIN on the EPSON PrivateLine Support card included

in your Owner’s Kit. This is the fastest way of speaking to a live

representative, and it’s free. This service is available 6

AM to 6 PM,

Pacific Time, Monday through Friday, for the duration of your

warranty period.

You may also speak with a projector support specialist by dialing one

of these numbers:

■U.S.: (562) 276-4394, 6 AM to 6 PM, Pacific Time, Monday

through Friday

■Canada: (905) 709-3839, 6 AM to 6 PM, Pacific Time, Monday

through Friday

Toll or long distance charges may apply.

Electronic support services

Service Access

World Wide Web From the Internet, you can reach EPSON’s product

support page at http://support.epson.com. After

selecting your product, you can access

troubleshooting information, download product

documentation, and receive technical advice

through e-mail.

Presenters Online Access tips, templates, and training for developing

successful presentations at

http://www.presentersonline.com

80 Solving Problems

Before you call, please have the following information ready:

■Product name (EPSON PowerLite 600p, 800p, or 810p)

■Product serial number (located on the bottom of the projector)

■Computer configuration

■Description of the problem

You can purchase screens, carrying cases, or other accessories

from EPSON at (800) 873-7766 or by visiting the EPSON Store at

www.epsonstore.com (U.S. sales only). In Canada, please call

(800) 873-7766 for dealer referral

Appendix A: Connecting to Additional Equipment

Appendix A: Connecting to

Additional Equipment

This appendix explains how to connect the projector to a desktop PC

or Macintosh, high-end workstation, more than one computer, or a

DVI video source. It also provides guidance on setting up the

projector in a permanent installation.

The following information is covered:

■Installing the projector

■Connecting to a PC desktop computer

■Connecting to a desktop Macintosh

■Connecting to a second computer

■Connecting to a high-end workstation

■Connecting to a DVI video source

82 Appendix A: Connecting to Additional Equipment

Installing the Projector

The projector can be installed for four different viewing setups: front

projection, ceiling mounting, rear projection onto a semi-transparent

screen, or rear/ceiling projection, as shown:

To project from overhead, you’ll need to select

Ceiling in the

projector’s Advanced menu. To project from the rear, select

Rear

Proj . See “Setting Advanced Features” on page 55.

If you’re mounting the projector on the ceiling and you place it above

screen level, you’ll have to tilt it down to position the image on-screen.

This causes the image to lose its square shape. You can then correct

the distortion by using the

V Keystone function in the projector’s

menu system (see “Customizing Projector Features” on page 53) or by

using the Keystone buttons on the projector’s control panel.

If you place the projector’s lens so it’s level with the top of the screen,

the image will be square and you won’t have to adjust it. If you place

the lens lower than the top of the screen, you’ll have to tilt the

projector upward if you want to fill the whole screen with the image.

front projection ceiling mounting

rear projection rear/ceiling projection

note

See “Positioning the

Projector” on page 10 for

more information.

Appendix A: Connecting to Additional Equipment

Connecting to an External Audio System

The projector’s internal speakers are loud enough for most rooms.

However, if your installation requires maximum volume and sound

quality, you can connect the projector to external speakers or a public

address (PA) system. This disables the projector’s internal speakers.

If you’ve connected multiple audio and video sources to the projector,

the projector will automatically switch the audio along with the video

source whenever you choose a different video source. (See “Switching

Between Picture Sources” on page 28 or page 33.)

To connect the projector to an external sound system, you will need

an RCA-to-3.5 mm stereo audio cable, which may be included with

your sound system, or may be purchased from an electronics store.

Before you start, make sure the projector and speakers or PA system

are turned off.

1. Connect the cable’s 3.5-mm stereo miniplug to the projector’s

Audio Out jack.

2. Connect the RCA plugs on the opposite end of the cable to the

left and right jacks of your speaker or PA system.

Audio Out jack

84 Appendix A: Connecting to Additional Equipment

Connecting to a PC Desktop Computer

You can connect the projector to any IBM-compatible PC. This

section includes instructions for the following:

■Connecting the computer cable

■Connecting the mouse cable (if you want to use the remote

control as a mouse or use USB audio)

■Connecting the audio cable (if you’ll be projecting with audio)

Follow the steps in each section for the cables you need to connect.

Before beginning, make sure the projector and computer are turned

off. If you need help with positioning the projector, see page 10.

Connecting the Computer Cable

1. Disconnect the monitor cable from the video port on the back of

the computer.

2. If you’ll be viewing the display on your computer monitor as well

as the projector screen, connect the monitor cable to the

projector’s

Monitor Ou t port, as shown.

Monitor

Out port

Appendix A: Connecting to Additional Equipment

3. Connect one end of the computer cable to the projector’s

Computer2/Component Video port, as shown.

4. Connect the other end of the cable to the computer’s video port.

5. Tighten the screws on the connectors.

Computer2/Component Video Port

86 Appendix A: Connecting to Additional Equipment

Connecting the Mouse Cable

To use the remote control as a mouse, follow the steps below. You’ll

use a different mouse cable, depending on whether your computer has

a round PS/2 mouse port or a flat USB port.

The USB cable also provides audio support. If your computer

supports USB and your presentation includes sound, you can play it

through the projector’s speakers by connecting the USB cable.

1. Connect the square end of the USB cable to the projector’s USB

port as shown.

2. Disconnect your mouse from the port on the back of your

computer and replace it with the other end of the cable. (Your

computer’s mouse will be disabled while you are using the remote

control as a mouse.)

note

If you have a PC with a

serial mouse port, you’ll need

a serial mouse cable. See your

projector dealer to obtain the

correct cable.

USB cable

USB port

Appendix A: Connecting to Additional Equipment

Connecting the Audio Cable

If your presentation includes sound and you want to use the

projector’s built-in speakers, you’ll need to connect a stereo, mini-jack

audio cable (not included). If you connected the USB cable, you may

not need a separate audio cable.

1. Connect one end of the audio cable to the

Audio 1 jack on the

projector.

2. Connect the other end of the audio cable to the speaker or

audio out port on the computer’s sound card.

audio cable

Audio 1 jack

88 Appendix A: Connecting to Additional Equipment

Connecting to a Desktop Macintosh

You can connect the projector to any desktop Macintosh. This section

includes instructions for the following:

■Connecting the computer cable

■Connecting the mouse cable (if you want to use your remote

control as a mouse or use USB audio)

■Connecting the audio cable (if you’ll be projecting with audio)

Follow the steps in each section for the cables you need to connect.

Before beginning, make sure the projector and computer are turned

off. If you need help with positioning the projector, see page 10.

Connecting the Computer Cable

1. Disconnect the monitor cable from the video port on the back of

the Macintosh.

2. If you’ll be viewing the display on your computer monitor as well

as the projector screen, connect the monitor cable to the

projector’s

Monitor Out port, as shown.

note

Macintosh configurations

vary. See your computer

manual for the location of the

ports needed to connect your

projector. Older models may

require a Macintosh adapter

set, which you may purchase

rom EPSON; see page 8.

Monitor

Out port

Appendix A: Connecting to Additional Equipment

3. Connect one end of the computer cable to the projector’s

Computer 2/ Component Video port, as shown.

4. Connect the other end of the computer cable to the video port on

the Macintosh. If it doesn’t fit, you may have to use a Macintosh

desktop adapter, which you can buy from EPSON (see page 8).

To use the adapter, remove its cover as

shown and set its DIP switches according

to the resolution you want to use, such as

16-inch mode. See your Macintosh

documentation for instructions.

Replace the cover and connect the

adapter to the free end of the computer

video cable. Then plug the cable (with

the adapter) into the video port on your

Macintosh.

5. Tighten the screws on the connectors.

Macintosh desktop

adapter (if needed)

Computer2/Component Video port

90 Appendix A: Connecting to Additional Equipment

Connecting the Mouse Cable

To use the remote control as a mouse follow the steps below. If the

Macintosh has a USB port, you can use the USB mouse cable

included with the projector. If it has a round mouse port, you’ll need a

Macintosh mouse cable; see your projector dealer for help in obtaining

the correct cable.

The USB cable also provides audio suport. If your Macintosh supports

USB and your presentation includes sound, you can play it through

the projector’s speakers by connecting the USB cable.

1. Connect the square end of the USB cable to the projector’s

USB

port.

2. Disconnect your Macintosh’s mouse cable. Connect the other end

of the projector’s mouse cable to a USB port on your Macintosh.

USB port

USB cable

Appendix A: Connecting to Additional Equipment

Connecting the Audio Cable

If your presentation includes sound and you want to use the

projector’s built-in speakers, you’ll need to connect a stereo, mini-jack

audio cable (not included). If you connected the USB cable, you may

not need a separate audio cable.

1. Connect one end of the audio cable to the

Audio 1 jack on the

projector.

2. Connect the other end of the audio cable to the speaker or audio

out port on the Macintosh.

Audio1 jack

audio cable

92 Appendix A: Connecting to Additional Equipment

Connecting to a Second Computer

To connect a second computer to the projector, you need to use the

projector’s

Computer1 port. You’ll need an optional DVI-analog

cable, unless the computer supports DVI (Digital Visual Interface)

video.

1. Connect one end of the cable to the computer’s video port.

2. Connect the other end to the projector’s

Computer1 port as

shown.

3. To display images properly, make sure the

Comp1 Input option

in the projector’s Setting menu is set correctly. See page 54 for

instructions.

4. If you want to hear the computer’s audio through the projector,

you’ll need to connect the USB cable or purchase an RCA-to-

3.5 mm stereo cable (available from your electronics store or video

dealer).

Insert the cable’s 3.5-mm plug into your computer’s audio-out

port. Then attach the connectors at the other end of the cable to

the projector’s

Audio 2 jacks, matching the white plug to the

L jack and the red plug to the

R jack.

Computer 1 port

Appendix A: Connecting to Additional Equipment

Connecting to a High-End Workstation

There is no across-the-board standard for workstation video output.

However, your PowerLite projector is capable of remapping input

resolutions up to 1600×1200 pixels. Workstations that follow the

SXGA standard and use the HD15 (standard VGA) connector won’t

need an adapter cable or any special connection device. If your system

varies, contact your computer dealer for help in connecting your

workstation.

Connecting to a DVI Video Source

The projector’s DVI (Digital Visual Interface) port receives pictures

directly from your computer in digital format. This lets the projector

display images of greater clarity than can be achieved using a standard

analog VGA connection.

To project images in digital video format, follow these steps:

1. Connect the computer’ ’s DVI cable to the projector s

Computer1

port.

2. To display images properly, make sure the

Comp1 Input option

in the projector’s Setting menu is set correctly. See page 54 for

instructions.

If you want to connect audio for this computer, use the projector’s

Audio 1 port; if you want to connect a mouse cable (to use the remote

control as a wireless mouse), use the

Mouse or USB port.

Computer1 port

94 Appendix A: Connecting to Additional Equipment

Appendix B: Notices95

Appendix B: Notices

This chapter i ncludes safety instructions and other important information

about your EPSON PowerLite projector.

Important Safety Instructions

Follow these safety instructions when setting up and using the projector:

■Do not place the projector on an unstable cart, stand, or table.

■Do not use the projector near water or sources of heat.

■Use the type of power source indicated on the projector. If you are not

sure of the power available, consult your dealer or power company.

■Place the projector near a wall outlet where the plug can be easily

unplugged.

Placez l’appareil près d’une prise de courant où la fiche peut être débranchée

facilement.

■Insert the projector’s three-wire grounding-type plug into a properly

grounded outlet. If you have a two-prong outlet, contact an electrician

to replace it. Do not hold the plug with wet hands.

■Take the following precautions for the plug. Failure to comply with

these precautions could result in sparks or fire: Do not insert the plug

into an outlet with dust present. Insert the plug firmly into the outlet.

■Do not overload wall outlets, extension cords, or integral convenience

receptacles. This can cause fire or electric shock.

■Do not place the projector where the cord can be walked on. This may

result in fraying or damage to the plug.

■Unplug the projector from the wall outlet before cleaning. Use a damp

cloth for cleaning. Do not use liquid or aerosol cleaners.

■Do not block the slots and openings in the projector case. They provide

ventilation and prevent the projector from overheating. Do not operate

the projector on a sofa, rug, or other soft surface, or in a closed-in

cabinet unless proper ventilation is provided.

96 Appendix B: Notices

■Never push objects of any kind through the cabinet slots. Never spill

liquid of any kind into the projector.

■Except as specifically explained in this User’s Guide, do not attempt to

service this product yourself. Refer all servicing to qualified personnel.

Opening or removing covers may expose you to dangerous voltages and

other hazards.

■Unplug the projector during lightning storms or when it will not be used

for extended periods.

■Do not place the projector and/or remote control on top of

heat-producing equipment or in a hot location.

■Unplug the projector from the wall outlet and refer servicing to qualified

service personnel under the following conditions: When the power cord

or plug is damaged or frayed. If liquid has been spilled into the

projector, or if it has been exposed to rain or water. If it does not operate

normally when you follow the operating instructions, or if it exhibits a

distinct change in performance, indicating a need for service. If it has

been dropped or the housing has been damaged.

■If you use the projector in a country other than where you purchased it,

use the correct power cord for that country.

■Do not stand on the projector or place heavy objects

on it.

■Do not use the projector outside of the required temperature range of 41

to 95 °F (5 to 35 °C). Doing so may cause an unstable display and could

lead to projector damage.

■Do not store the projector outside of the required temperature range of

14 to 140 °F (-10 to 60 °C) or in direct sunlight for long periods of time.

Doing so may cause damage to the case.

Appendix B: Notices97

Remote Control Information

You can operate the projector by remote control via a line-of-sight infrared

(IR) receiver at the front and rear of the projector. The projector may not

respond to remote control commands under the following conditions:

■There is an object between the remote control IR emitter and the IR

receiver on the projector.

■Ambient light is too bright.

■Certain types of fluorescent lighting are used.

■A strong light source shines into the IR receiver.

■Other equipment that emits infrared energy, such as a radiant room

heater, is in the room.

These conditions commonly cause problems for most infrared-controlled

equipment. Try the following:

■Make sure the remote control is turned on.

■The remote control unit’s batteries may be low on power; replace them.

■Dim the ambient lighting and/or turn off any fluorescent lights.

■Close any window coverings and/or move the projector out of direct

sunlight.

■Turn off other equipment that emits infrared energy.

If the remote control still does not work properly, remember you can always

control your computer-based presentation directly from the computer, even

in an environment containing one of the conditions listed above.

98 Appendix B: Notices

Declaration of Conformity

According to 47CFR, Part 2 and 15

Class B Personal Computers and Peripherals; and/or CPU Boards and Power

Supplies used with Class B Personal Computers

We: EPSON AMERICA, INC.

Located at: 3840 Kilroy Airport Way

MS: 6-43

Long Beach, CA 90806-2469

Telephone: (562) 290-5254

Declare under sole responsibility that the product identified herein, complies

with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each

product marketed, is identical to the representative unit tested and found to

be compliant with the standards. Records maintained continue to reflect the

equipment being produced can be expected to be within the variation

accepted, due to quantity production and testing on a statistical basis as

required by 47CFR §2.909. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may

cause undesired operation.

Trade Name: EPSON

Type of Product: Multimedia Projector

Model: EMP-600/800/810

Appendix B: Notices99

FCC Compliance Statement

For United States Users

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio or television reception.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause interference to radio and television

reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the

following measures:

■Reorient or relocate the receiving antenna.

■Increase the separation between the equipment and receiver.

■Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected.

■Consult the dealer or an experienced radio/TV technician for help.

WARNING

The connection of a non-shielded equipment interface cable to this

equipment will invalidate the FCC Certification of this device and may cause

interference levels which exceed the limits established by the FCC for this

equipment. It is the responsibility of the user to obtain and use a shielded

equipment interface cable with this device. If this equipment has more than

one interface connector, do not leave cables connected to unused interfaces.

Changes or modifications not expressly approved by the manufacturer could

void the user’s authority to operate the equipment.

For Canadian Users

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement

sur le materiel brouilleur du Canada.

100 Appendix B: Notices

Warranty

Epson America, Inc. Limited Warranty

Basic Two-Year Warranty and 90-Day Lamp Warranty

What Is Covered: Epson America, Inc. (“ ”EPSON ) warrants to the first end

user customer of the EPSON product enclosed with this limited warranty

statement that the product, if purchased and used in the United States or

Canada, conforms to the manufacturer’s specifications and will be free from

defects in workmanship and materials for a period of two (2) years from the

date of original purchase (except that the warranty period is 90 days for

projector lamps).

What EPSON Will Do To Correct Problems: If you elect carry-in warranty

service, please bring the product securely packaged in its original container or

an equivalent, along with proof of the date of original purchase, to your

EPSON Dealer or EPSON Customer Care Center. EPSON will, at its

option, repair or replace on an exchange basis the defective unit, without

charge for parts or labor. When warranty service involves the exchange of the

product or of a part, the item replaced becomes EPSON property. The

exchanged product or part may be new or previously repaired to the EPSON

standard of quality. Exchange or replacement products or parts assume the

remaining warranty period of the product covered by this limited warranty.

However, each replacement lamp carries the limited 90-day warranty stated

above.

What This Warranty Does Not Cover: This warranty covers only normal

consumer use in the United States and Canada. For lamps, 24-hour-per-day

use causes unusual strain and is not considered normal use. This warranty

does not cover consumables (e.g., fuses), other than lamps. EPSON is not

responsible for warranty service should the EPSON label or logo or the rating

label or serial number be removed or should the product fail to be properly

maintained or fail to function properly as a result of misuse, abuse, improper

installation, neglect, improper shipping, damage caused by disasters such as

fire, flood, and lightning, improper electrical current, software problems,

interaction with non-EPSON products, or service other than by an EPSON

Authorized Servicer. Postage, insurance, or shipping costs incurred in

presenting your EPSON product for carry-in warranty service are your

responsibility. If a claimed defect cannot be identified or reproduced in

service, you will be held responsible for costs incurred.

THE WARRANTY AND REMEDY PROVIDED ABOVE ARE

EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESS OR IMPLIED

WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS

102 Appendix B: Notices

Appendix C: Technical Specifications 103

Appendix C: Technical

Specifications

General

Type of display Poly-silicon TFT active matrix

Size of LCD panels Diagonal: 0.9 inches (22.9 mm)

Lens F=1.74 to 2.06, f=28.3 mm to 37.98 mm

Resolution

(native format) 800p and 810p: 1024 × 768 pixels (XGA)

600p: 800 × 600 pixels (SVGA)

Color reproduction 24 bit, 16.7 million colors

Brightness 810p: 2000 lumens (ANSI)

800p: 1500 lumens (ANSI)

600p: 1700 lumens (ANSI)

Contrast ratio 400:1

Image size 30 to 300 inches

Projection distance 2.85 to 40.7 feet (0.87 to 12.4 meters)

Projection methods Front, rear, upside-down (ceiling mount)

Internal sound system 5 W monaural

Optical aspect ratio 4:3 (horizontal : vertical)

Zoom ratio 1:135

Noise level 38 dB

Keystone correction

angle Vertical: ± 30° (maximum)

Horizontal: ± 10° (maximum)

104 Appendix C: Technical Specifications

Projection Lamp

Type UHE (Ultra High Efficiency)

Power consumption 200 W

Lamp life About 1500 hours

Part number ELPLP15

Remote Control

Range 32.8 feet (10 meters)

Batteries Alkaline AA (2)

Mouse Compatibility

Supports PS/2 and USB

Dimensions

Height 4.1 inches (104 mm)

Width 13.7 inches (348 mm)

Depth 10.8 inches (274 mm)

Weight 9.3 lb (4.2 kg)

Electrical

Rated frequency 50/60 Hz AC

Power supply 100 to 120 VAC, 3.1A

200 to 240 VAC, 1.5 A

Power consumption Operating: 280 W

Standby: 5.5 W

Appendix C: Technical Specifications 105

Environmental

Temperature Operating: 41 to 95 °F (5 to 35 °C)

Storage: 14 to 140 °F (-10 to 60 °C)

Humidity Operating: 20 to 80% RH,

non-condensing

Storage: 10 to 90% RH,

non-condensing

Safety

United States FCC Part 15J Class B

UL1950 Rev. 3

Canada DOC SOR/88-475

CSA C22.2 No. 950 Rev. 3 (cUL)

CE Marking Directive 73/23/EEC

EN 60950

Directive 89/336/EEC

EN 55022, EN 55024

106 Appendix C: Technical Specifications

Compatible Video Formats

The projector supports NTSC, PAL, and SECAM international video

standards, as well as the monitor display formats listed below.

To project images output from a computer, the computer’s video card

must be set at a refresh rate (vertical frequency) that’s compatible with

the projector; see the following table for compatible formats. As noted

below, some images are automatically resized to display in one of the

projector’s “native” formats (such as XGA). In addition, the

frequencies of some computers may not allow images to display

correctly; see your computer’s documentation for details.

Mode Refresh Rate (Hz) Resolution

PC98 57 640 × 400

VGAEGA 70 640 × 350

VGA60 60 640 × 480

VESA72 72 640 × 480

VESA75 75 640 × 480

VESA85 85 640 × 480

VGA120 120 640 × 480

SVGA56 56 800 × 600

SVGA60 60 800 × 600

SVGA72 72 800 × 600

SVGA75 75 800 × 600

SVGA85 85 800 × 600

SVGA120 120 800 × 600

XGA43i 43 1024 × 7681

XGA60 60 1024 × 7681

XGA70 70 1024 × 7681

XGA75 75 1024 × 7681

XGA85 85 1024 × 7681

XGA120 120 1024 × 7681

SXGA1—70 70 1152 × 8642

SXGA1—75 75 1152 × 8642

SXGA1—85 85 1152 × 8642

SXGA1—100 100 1152

× 8642

SXGA2—60 60 1280 × 9602

SXGA2—75 75 1280 × 9602

SXGA2—85 85 1280 × 9602

SXGA3—43i 43 1280 × 10242

SXGA3—60 60 1280 × 10242

Appendix C: Technical Specifications 107

1The image is resized so that it displays using one of the projector’s native

formats. (PowerLite 600p only.)

2The image is resized so that it displays using one of the projector’s native

formats.

3Not supported on the PowerLite 600p

SXGA3—75 75 1280 × 10242

SXGA3—85 85 1280 × 10242

SXGA+60 60 1400 × 10502

SXGA+75 75 1400 × 10502

SXGA+85 85 1400 × 10502

UXGA48i 48 1600 × 12002,3

UXGA60 60 1600 × 12002,3

UXGA65 65 1600 × 12002,3

UXGA70 70 1600 × 12002,3

UXGA75 75 1600 × 12002,3

UXGA80 80 1600 × 12002,3

UXGA85 85 1600 × 12002,3

iMAC VGA 117 640 × 480

iMAC SVGA 95 800 × 600

iMAC XGA 75 1024 × 7681

MAC II 13 67 640 × 480

MAC16 75 832 × 624

MAC19 75 1024 × 7681

MAC21 75 1152 × 8702

TV525i 60 2

TV625i 50 2

SDTV525p 60 2

HDTV750p 60 2

HDTV1125i 60 2

NTSC 60 2

NTSC4.43 60 2

PAL 50 2

M-PAL 60 2

N-PAL 50 2

PAL60 60 2

SECAM 50 2

Mode Refresh Rate (Hz) Resolution

108 Appendix C: Technical Specifications

Computer Video Port Pin Assignments

The Computer2/Component Video port is a female video RGB,

15-pin micro-D-style connector. Here are its pin assignments:

Pin no. Computer port

1 Red video

2 Green video

3 Blue video

4 GND

5 GND

6 Red GND

7 Green GND

8 Blue GND

9 Reserved

10 Synchronous GND

11 GND

12 SDA

13 Horizontal sync / composite sync

14 Vertical sync

15 SCL

Index 109

Index

A/V Mute, 28, 52, 54

A/V Mute button, 28, 34

About menu, 42, 56 to 57, 65

Accessories, 7 to 8, 80

Adobe Acrobat Reader, 3 to 4

Advanced menu, 42, 55 to 56

Air filter, cleaning and replacing, 61 to 62

Anti-theft device, 8, 11

Arrow button, remote control, 40

Aspect ratio, 27, 103

Audio

adjusting tone, 49

adjusting volume, 28, 34, 49

connecting desktop, 87, 91

connecting laptop, 14

connecting second computer, 92

menu, 42, 49

outputting to external sound system, 83

problems, troubleshooting, 77

turning off (using A/V Mute), 28, 34

Audio Out jack, 83

Auto button, 27, 46

Back adjustable foot, 25

Bar tool, 38, 50

Bass, adjusting, 49

Batteries, installing, 32

Blank screen, 22 to 23

Blurry image, 75

Brightness, 1, 103

Brightness setting, 46

Cables

A/V, 6 to 8, 15 to 18

audio, 6 to 8, 14, 83, 87, 91

computer, 6 to 8, 12, 84 to 85, 88 to 89

Cables, (continued)

mouse, 6 to 8, 13, 86, 90

purchasing, 8

USB, 6 to 8, 13, 86, 90

video, 6 to 8, 15 to 18

Capturing image, 51 to 52

Carrying case, 8, 66

Ceiling mount, 8, 82

Cleaning

air filter, 61 to 62

lens, 60

projector case, 60

Color

problems, 77

settings, 46 to 47, 55

Color Mode setting, 47

Comp1 button, 33, 54, 77

Comp2/YCbCr button, 33, 54, 77

Component video cable, 7, 15

Composite video cable, 15

Computer

cable, 6

saving settings for, 48

Computer connector pin assignments, 108

Computer/YCbCr button, 28, 77

Computers supported, 1

Connecting projector

to a desktop Macintosh, 88 to 91

to a desktop PC, 84 to 87

to a DVI computer source, 93

to a high-end workstation, 93

to a laptop, 12 to 14

to a second computer, 92

to a video source, 15 to 18

Connector pin assignments, 108

Contrast setting, 46

Cursor/Stamp tool, 37, 50

110 Index

Declaration of Conformity, 98

Default settings, restoring, 44, 57

Desktop adapter, Macintosh, 88 to 89

Desktop computer, connecting, 84 to 87,

88 to 91

Digital visual interface, see DVI

Distance from projector to screen, 10, 103

Down arrow button, remote control, 40

Drawing on the screen, 37 to 38

DVI (Digital Visual Interface)

cable, 7, 8

source, connecting to, 93

Effect menu, 42, 50 to 51

Electrical specifications, 104

Enter button, 33, 39

Environmental specifications, 105

EPSON

accessories, 8, 80

PrivateLine Support, 5, 79

technical support, 4 to 5, 79 to 80

Esc button, 39

E-Zoom button, 35

FCC compliance statement, 99

Filter

See Air filter

Focusing, 24

Foot release button, 25

Freeze button, 34

Height of image, adjusting, 25

Help, 4 to 5, 79 to 80

Help button, 68

Help system, using, 68 to 69

Highlighting tools, 37 to 38, 50 to 51

H-Keystone setting, 53

iBook, connecting to, 12

iMac, connecting to, 7

Image

adjusting, 24 to 27, 45 to 47

capturing and saving in projector, 51 to 52

correcting shape, 26, 53, 74

focusing, 24

height, adjusting, 25

positioning, 25, 46

problems with, troubleshooting, 72 to 77

raising, 25

resizing, 27, 35

shape, correcting, 26, 53, 74

size and projection distance, 10, 103

turning off (using A/V Mute), 28, 34

zooming, 24 to 25, 35

Installing projector, 82 to 83

Kensington anti-theft device, 8, 11

Keystone correction, 26, 53, 74, 103

Lamp

number of hours used, 56

replacing, 62 to 65

status light, 69 to 71

Lamp timer, resetting, 65

Language setting, 68

Laptop computer

connecting to, 12 to 14

displaying on, 23, 73

Lens

cleaning, 60

specifications, 103

Lights, status, 69 to 72

Lines, drawing on screen, 38

Logo, saving on projector, 51 to 52

Index 111

Macintosh

connecting, 88 to 91

desktop adapter, 88 to 89

Manuals, 3 to 5

Menus

About, 42, 56 to 57, 65

Advanced, 42, 55 to 56

Audio, 42, 49

changing settings, 42 to 44

Effect, 42, 50 to 51

Reset All, 42, 57

Setting, 42, 53 to 54

User’s Logo, 42, 51 to 52

using, 42 to 44

Video, 42, 45 to 47

Mouse buttons, 39 to 40

New Hardware Wizard, 21

No-Signal Msg setting, 54

Options for projector, 8

P in P (picture in picture) button, 36

Picture source, selecting, 28, 33

Picture, see Image

Picture-in-picture video source, selecting, 53

Pin assignments, connector, 108

Pointer tool, 37, 50

Positioning

image, 24 to 25

projector, 10 to 11

Power

button, 21

specifications, 104

status light, 69 to 71

Presenters Online, 4, 79

Preset button, 48

PrivateLine Support, 5, 79

Problems

color, 77

image, 72 to 77

remote control, 78

sound, 77

Projection lamp

See Lamp

Projector

carrying case, 8, 66

cleaning, 60 to 62

connections, see Connecting projector

distance from screen, 10, 103

feet, adjusting height with, 25

installing, 82 to 83

lamp specifications, 104

options, 8

positioning, 10 to 11

resolution, 1, 103

specifications, 103 to 108

transporting, 66

troubleshooting, 67 to 77

turning off, 29

turning on, 20 to 23

unpacking, 6 to 7

viewing information about, 56 to 57

Prompt setting, 54

Raising image, 25

Rear-screen projection, 82

Registration, 5

Remote control

information, 97

numbered buttons, 37

problems, 78, 97

specifications, 104

troubleshooting, 78

turning on, 32

using, 31 to 40

wireless mouse, using as, 39 to 40

Replacing lamp, 62 to 65

Reset All menu, 57

Resetting lamp timer, 65

Resetting menu options, 42, 44, 57

112 Index

Resizing image, 27, 35

Resolution, 1, 47, 103

Safety

instructions, 95 to 97

specifications, 105

Screen

blank, 22 to 23

distance from projector, 10

Screen image

See Image

Setting menu, 42, 53 to 54

Shift button, 76

Sleep mode, 29, 54

Sound

adjusting, 49

See Audio

turning off (using A/V Mute), 28

Source, selecting, 28, 33

Speaker, specifications, 103

Speakers, connecting to external, 83

Special effects buttons, 37 to 38

Specifications

brightness, 1, 103

dimensions, 104

electrical, 104

environmental, 105

general, 103

lens, 103

remote control, 104

resolution, 1, 103

safety, 105

Spotlight tool, 38, 50

Startup screen, creating, 51 to 52

Status lights, 69 to 72

Stopping action, 34

Support, see Technical support

S-Video button, 33, 77

S-Video cable, 7, 15

Switching picture source, 28, 33

Sync buttons, 26, 76

Synchronization, adjusting, 27, 46

Technical support, 4 to 5, 79 to 80

Temperature

requirements, 105

status light, 69

Tone setting, 49

Tracking buttons, 26, 76

Tracking, adjusting, 27, 46

Transporting projector, 66

Treble, adjusting, 49

Troubleshooting

blank screen, 22 to 23

image and sound problems, 72 to 77

projector problems, 67 to 77

remote control problems, 78

Turning off picture (using A/V Mute), 28, 34

Turning off projector, 29

Turning on projector, 20 to 23

Unpacking projector, 6 to 7

Up arrow button, remote control, 40

USB

audio, 21

cable, 6 to 7, 13, 86, 90

User’s Logo menu, 42, 51 to 52

Video

button, 28, 33

cables, 6 to 8, 15 to 18

display settings, viewing, 56

formats, supported, 1, 106 to 107

menu, 42, 45 to 47

picture in picture, 53

selecting source, 28, 33

Video button, 77

Video port pin assignments, 108

Video sources, connecting projector to,

15 to 18

V-Keystone setting, 53

Index 113

Volume

adjusting, 28, 34, 49

button, 28, 34

setting, 49

Warning lights, 69 to 72

Warranty, 5, 100 to 101

Workstations, connecting projector to, 93

Zoom ratio, 103

Zooming image, 24 to 25, 35

114 Index

Product specificaties

Merk:	Epson
Categorie:	Beamer
Model:	PowerLite 800p

Heb je hulp nodig?

Als je hulp nodig hebt met Epson PowerLite 800p stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Beamer Epson

Epson EB-L520U Handleiding

14 December 2024

Epson EB-L630U Handleiding

14 December 2024

Epson ELPAF63 Handleiding

14 December 2024

Epson ELPFP15 Handleiding

14 December 2024

Epson ELPMB67 Handleiding

14 December 2024

Epson ELPLX01S Handleiding

14 December 2024

Epson ELPMB56 Handleiding

14 December 2024

Epson 421i Handleiding

21 November 2024

Epson EF22R Handleiding

5 November 2024

Epson EF21R Handleiding

5 November 2024

Handleiding Beamer

Nieuwste handleidingen voor Beamer

Philips NeoPix 200 NPX200 Handleiding

4 Maart 2025

Philips NeoPix 130 Smart Handleiding

4 Maart 2025

InFocus Genesis IN0028SL Handleiding

25 Februari 2025

Strong MIRA 1 Handleiding

20 Februari 2025

InFocus Genesis IN0026ST Handleiding

20 Februari 2025

Sharp XP-P601Q Handleiding

20 Februari 2025

Acer PL6820 Handleiding

10 Februari 2025

Acer X1328 Handleiding

30 Januari 2025

Acer Vero PD2328 Handleiding

30 Januari 2025

Acer PD2528ic Handleiding

30 Januari 2025