Epcom X6465A Handleiding

Epcom Niet gecategoriseerd X6465A

Lees hieronder de 📖 handleiding in het Nederlandse voor Epcom X6465A (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

A low prole LED beacon with a long, maintenance-free

service life. These beacons are ideal for industrial vehicle

applications and feature a 12-80 VDC operating range.

Do not install and/or operate this safety product unless you have read and understand the

safety information contained in this manual.

1. Proper installation combined with operator training in the use, care, and maintenance of emergency warning devices

are essential to ensure the safety of you and those you are trying to protect.

2. Exercise caution when working with live electrical connections.

3. This product must be properly grounded. Inadequate grounding and/or shorting of electrical connections can cause

high current arcing, which can cause personal injury and/or severe vehicle damage, including re.

4. Proper placement and installation are vital to the performance of this warning device. Install this product so that output

performance of the system is maximized and the controls are placed within convenient reach of the operator so that

s/he can operate the system without losing eye contact with the roadway.

5. It is the responsibility of the vehicle operator to ensure during use that all features of this product work correctly. In

use, the vehicle operator should ensure the projection of the warning signal is not blocked by vehicle components (i.e.,

open trunks or compartment doors), people, vehicles, or other obstructions.

6. The use of this or any other warning device does not ensure all drivers can or will observe or react to a warning signal.

Never take the right-of-way for granted. It is your responsibility to be sure you can proceed safely before entering an

intersection, driving against trafc, responding at a high rate of speed, walking on or around trafc lanes.

7. This equipment is intended for use by authorized personnel only. The user is responsible for understanding and obey-

ing all laws regarding warning signal devices. Therefore, the user should check all applicable city, state, and federal

laws and regulations. The manufacturer assumes no liability for any loss resulting from the use of this warning device.

WARNING!

Failure to install or use this product according to manufacturer’s recommendations may result in property

damage, serious bodily/personal injury, and/or death to you and those you are seeking to protect!

Page 1 of 3

Installation and Operation Instructions

LED Beacon

Specications:

Size: Permanent Mount W: 5.1” x H: 4.2”

Magnet Mount W: 5.1” x H: 4.3”

Weight: Permanent Mount 0.6 lb.

Magnet Mount 1.6 lb.

Voltage: 12-80 VDC systems

Current Draw: 150 mA

Pulse 8: 85 FPM

Important! This unit is a safety device, and it must be con-

nected to its own separate, fused power point to assure its

continued operation should any other electrical accessory fail.

Page 2 of 3

WARNING!

Maximum recommended vehicle speed for safe oper-

ation using the Magnet Mount model is 65 mph (104

km/h) on a well maintained road, when tted to the

center of a vehicle roof of steel construction. Higher

speeds could cause the mount to fail, resulting in the

beacon ying off of the vehicle, which could cause

damage to other vehicles and injury or death to the

passengers.

The magnet mount is not intended as a permanent mounting

for the beacon. The magnet mount unit must be mounted on

a magnetic surface (i.e. no berglass, etc.). Insure that the

magnet is kept clean.

Installation & Mounting:

Carefully remove the beacon and place it on a at surface. Ex-

amine the unit for transit damage, broken lenses, etc. If damage

is found, contact the transit company or distributor. Do not use

damaged or broken parts.

Mounting:

Permanent

Position the unit in the desired mounting location. Using the base

as a template, mark the mounting hole locations. Drill three 3/16”

mounting holes, and drill one hole for power wire routing. The use

of a grommet is recommended for wires passing through compart-

ment walls. Mount the beacon using #10 hardware.

Mounting:

Temporary, magnet

Comes complete with a magnet, a fteen foot cord and a ciga-

rette lighter plug. A magnet mount kit is also available.

Note: These units are not sealed on the bottom. For

operation in an extremely moist environment or as added

protection against moisture, sealing the wire exit hole on

the bottom with a pliable caulking material is

recommended.

Note: Operating the vehicle without the lens installed on the

product may result in damage that will NOT be covered under

warranty

Wiring:

The wiring for this conguration is as shown in Figure 1 below.

The positive line must have a 3 amp fuse, as shown. A switch

may be used to control the on/off function

RED WIRE

SWITCH

(USER SUPPLIED)

FUSE (3 AMP)

(USER SUPPLIED)

BATTERY

GROUND GROUND

BLACK WIRE

CAUTION: HIGH VOLTAGE. Before servicing light, turn

“OFF” power and wait ve minutes.

920-1022-01 Rev. A Page 3 of 3

Manufacturer Limited Warranty and Limitation of Liability:

Manufacturer warrants that on the date of purchase this product will conform to Manufacturer’s specications for this product (which are

available from the Manufacturer upon request), and Manufacturer further warrants that this product is free from defects in materials and

workmanship. This Limited Warranty extends for thirty six (36) months from the date of purchase. Manufacturer will, at its discretion, repair

or replace any product found by the Manufacturer to be defective and subject to this Limited Warranty.

DAMAGE TO PARTS OR PRODUCTS RESULTING FROM TAMPERING, ACCIDENT, ABUSE, MISUSE, NEGLIGENCE, UNAPPROVED

MODIFICATIONS, FIRE OR OTHER HAZARD; IMPROPER INSTALLATION OR OPERATION; OR NOT BEING MAINTAINED IN ACCOR-

DANCE WITH THE MAINTENANCE PROCEDURES SET FORTH IN MANUFACTURER’S INSTALLATION AND OPERATING INSTRUC-

TIONS VOIDS THIS LIMITED WARRANTY.

ORAL STATEMENTS OR REPRESENTATIONS ABOUT THE PRODUCT WHICH MAY HAVE BEEN MADE BY SALESPEOPLE, DEAL-

ERS, AGENTS OR OTHER MANUFACTURER’S REPRESENTATIVES DO NOT CONSTITUTE WARRANTIES. THIS LIMITED WAR-

RANTY MAY NOT BE AMENDED, MODIFIED, OR ENLARGED EXCEPT BY A WRITTEN AGREEMENT SIGNED BY AN AUTHORIZED

OFFICIAL OF MANUFACTURER WHICH EXPRESSLY REFERS TO THIS LIMITED WARRANTY.

Exclusion of Other Warranties:

MANUFACTURER MAKES NO OTHER WARRANTIES, EXPRESS OR IMPLIED. THE IMPLIED WARRANTIES FOR MERCHANTABIL-

ITY OR FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED AND SHALL NOT APPLY TO THE PRODUCT. BUYER’S

SOLE AND EXCLUSIVE REMEDY IN CONTRACT, TORT, OR UNDER ANY OTHER THEORY AGAINST MANUFACTURER REGARDING

THE PRODUCT AND ITS USE SHALL BE THE REPLACEMENT OR REPAIR OF THE PRODUCT AS DESCRIBED ABOVE.

Limitation of Liability:

IN THE EVENT OF LIABILITY FOR DAMAGES ARISING OUT OF THIS LIMITED WARRANTY OR ANY OTHER CLAIM RELATED TO

THE MANUFACTURER’S PRODUCTS, MANUFACTURER’S LIABILITY FOR DAMAGES SHALL BE LIMITED TO THE AMOUNT PAID

FOR THE PRODUCT AT THE TIME OF THE ORIGINAL PURCHASE. IN NO EVENT SHALL MANUFACTURER BE LIABLE FOR LOST

PROFITS, THE COST OF SUBSTITUTE EQUIPMENT OR LABOR, PROPERTY DAMAGE, OR OTHER SPECIAL, CONSEQUENTIAL,

OR INCIDENTAL DAMAGES BASED UPON ANY CLAIM FOR BREACH OF CONTRACT, IMPROPER INSTALLATION, NEGLIGENCE,

OR OTHER CLAIM, EVEN IF MANUFACTURER OR A MANUFACTURER’S REPRESENTATIVE HAS BEEN ADVISED OF THE POS-

SIBILITY OF SUCH DAMAGES. MANUFACTURER SHALL HAVE NO FURTHER OBLIGATION OR LIABILITY WITH RESPECT TO THE

PRODUCT OR ITS SALE, OPERATION AND USE, AND MANUFACTURER NEITHER ASSUMES NOR AUTHORIZES THE ASSUMP-

TION OF ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SUCH PRODUCT.

This Limited Warranty denes specic legal rights. You may have other legal rights which vary from state to state. Some states do not allow

the exclusion or limitation of incidental or consequential damages.

www.syscom.mx

Product specificaties

Merk:	Epcom
Categorie:	Niet gecategoriseerd
Model:	X6465A
Hoogte:	106.68 mm
Soort:	Vast
Gebruikershandleiding:	Ja
Materiaal behuizing:	Nylon
Aantal lampen:	3 lampen
Type lamp:	LED
Plaatsing:	Binnen
Vormfactor:	Rond
Type stroombron:	DC
Certificering:	SAE J845 Class III
Aantal per verpakking:	1 stuk(s)
LED kleur:	Amber
Lamp(en) meegeleverd:	Ja
Diffusor type:	Gerichte projectie
Bevestigingstype:	Schroeven
Diffusor kleur:	Amber
Lamp inbegrepen:	Ja
Diffusor betekenis:	Opgelet