EMOS P5603N Handleiding

EMOS Thermostaat P5603N

Lees hieronder de 📖 handleiding in het Nederlandse voor EMOS P5603N (36 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/36

THERMOSTAT

TERMOSTAT

SK TERMOSTAT

PL TERMOSTAT

TERMOSZTÁT

TERMOSTAT

RS HR| |BA

TERMOSTAT

DE THERMOSTAT

ТЕРМОСТАТ

TERMOSTAT

LT TERMOSTATAS

LV TERMOSTATS

2101101010_31-P5603N 105 × 148 mm

GB T3 THERMOSTAT

The T3 thermostat is designed to monitor and control heating systems. It is equipped with a timed

room temperature reduction (SET-BACK) function with repetition every 24 hours. It is a simple system

of temperature control in a designated area. The thermostat is designed for indoor use. It is typically

located in places such as oces, schools, shops, houses, etc.

Specications

Range of temperature control: 5 °C to 30 °C

Maximum switching load: 7 A resistive, 3 A inductive

Power supply: 230 V AC 50/60 Hz

Set-back timing: 6 h/day repeated

Control switches: MCV controlled by on/o relay

System indication: Green LED indicates that the Set-back function is active. When the Set-back temper-

ature is to drop by 5 °C, the LED is orange.

Operating temperature: 0 °C to 40 °C

Storage temperature: -20 °C to 60 °C

Dimensions: 97 × 67 × 28 mm

ON indicator

L (live) N (neutral)

Install while power supply is OFF

Installation

1. Make sure to read the instruction manual carefully before the rst use of the thermostat, as well as the

boiler and air conditioning equipment. Turn o power supply before installing the thermostat!

Installation should be carried out by qualied personnel! During installation, observe the appropriate

standards.

2. Choose a suitable location for the thermostat where air circulates freely, with no devices producing

heat in the vicinity, such as a TV set. The thermostat should not be exposed to direct sunshine. We

recommend mounting the thermostat more than 1.5 m above the oor. Note: Never mount the

thermostat on a conductive surface.

3. Open the cover of the thermostat - loosen the screw at the bottom of the unit and remove the top

cover, as shown in Figure A.

4. There are two mounting holes on the back side. Place the unit on the wall and mark locations of the

holes on the wall. Drill 6mm holes into the wall, insert dowels into holes and using screws mount the

thermostat on the wall. No dowels are necessary if the thermostat is mounted on a wooden surface.

In that case, drill 2.6 mm holes.

5. Connection to electrical power: Thermostat is designed for switching max. 230 V/7 A. Never exceed

this limit, otherwise the thermostat will be damaged (burned). Thermostat has three power terminals:

NIN, LIN and LOUT. Use Figure B to connect lines between the thermostat and the switched heat

generating device (HEAT icon).

IMPORTANT: Ensure power supply is OFF when installing the thermostat.

6. Turn the knob of the switch so that the marking on the dial is aligned with markings on the wheel,

replace the front cover and gently screw up (Figure C).

7. Turn ON power supply. If the switching indicator (blue LED) blinks twice, the installation was ne.

Within several seconds, the thermostat automatically switches to the heating control mode with

the LED ON.

Note: If the switching indicator (blue LED) does not blink, turn OFF power supply, check the wiring and turn

the unit ON again.

Operation

1. Turning ON the thermostat temperature control: Set the switch to “HEAT”. Thermostat will control

the room temperature.

2. Room temperature is controlled by adjusting the knob to the desired temperature which is on the

dial.

3. Once the thermostat switches the heating system ON, the indicator light goes ON. Thermostat has

built-in protection against rapid cycle change - time delay switch - thermostat does not react to

changing temperature settings immediately.

4. Turning OFF the thermostat temperature control: Set the switch to “OFF”. Now the room temperature

control will be disabled (control of the heating system will be permanently o).

Automatic temperature reduction “SET-BACK”

The function provides temperature reduction of 5 °C for a xed time interval. For example, if the

temperature of the dial is set to 22 °C, it will be reduced to 17 °C during the SET BACK mode activation.

The time period of the set-back function is 6 hours. For example, if the SET-BACK changes the tempera-

ture at 23 h, then the originally set value is resumed at 5 hours. The cycle of the SET-BACK temperature

change will be repeated until the function is switched o.

Activating the SET-BACK mode

1. Press the button, the SET-BACK function is turned on and the function LED will be orange.

2. Six hours later, the temperature automatically returns to the originally set temperature. The SET-BACK

function LED is green.

3. The following day at the same time, the SET-BACK function will again automatically turn the tem-

perature to the reduced value.

4. To disable the SET-BACK function, press the button again. The function LED goes out.

Product specificaties

Merk:	EMOS
Categorie:	Thermostaat
Model:	P5603N
Breedte:	28 mm
Diepte:	97 mm
Hoogte:	67 mm
Beeldscherm:	Nee
Memory-functie:	Nee
Temperatuur omvang (T-T):	5 - 30 °C
Afstandsbediening inbegrepen:	Ja
AC-ingangsfrequentie:	50 Hz
Slimme thermostaat:	Nee
Maximale schakelspanning:	230 V