Electro-Voice EVI-AC Handleiding

Electro-Voice Niet gecategoriseerd EVI-AC

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro-Voice EVI-AC (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

EV-I Access Card

Access Card for Plug-In

Loudspeaker Diagnostics

User Instructions

Tools Required:

Instructions:

1. #2 Phillips Screwdriver 2. Ohm Meter capable of accurate

measurements below 50 ohms

1. If applicable, remove screws holding the security cover, gland nut cover, or NL4 cover in

place. Note position of the switch card. The card must be replaced in exactly the same

position as it was originally or system performance will be adversely affected!

2. Carefully remove the switch card and set it aside. Plug the Access Card onto the header in

place of the switch card. Note that the Access Card, unlike the switch card, will only fit in

one position centered on the input cup (See Figure 1).

3. Turn on the Ohm Meter and set it to the low ohms (x1) scale. Short the two probes togeth-

er and calibrate the meter to “Zero” (See Figure 2). If your meter does not have this calibra-

tion feature, note the ohms reading. This is the residual internal resistance of the meter,

probes and test leads. You will need to DEDUCT this number from the results you measure

at the Access Card.

The Access Card is a unique feature of the EV-Innovation series loudspeaker families. This

simple plug-in device allows diagnostic access to the transducers and protection circuitry

inside the enclosure WITHOUT requiring any disassembly or disconnections beyond simple

removal and replacement of the plug-in switch card. DCR values described in these instruc-

tions are typical for EV-I series two-way systems (eg: EVF-1122S/64). For complete model-

specific DCR values, consult the chart on page 4.

Figure 1:

Switch Card Removal / Access Card Install

Figure 2:

Ohm Meter Calibration

Adjust

0.0

<50.0





1. Test the woofer: Place one test lead securely on each of the RED test points on the Access

Card. A properly functioning woofer will read approximately 5.0 ohms DCR, ±0.5 ohm (See

Figure 3). A significantly higher reading indicates an open voice coil, meaning the woofer

must be replaced. A significantly lower reading indicates a voice coil that is shorting, mean-

ing the woofer must be replaced.

2. Test the compression driver: Place one test lead securely on each of the YELLOW test

points on the Access Card. A properly functioning compression driver will read approxi-

mately 4.3 ohms DCR, ±0.5 ohm (See Figure 4). A significantly higher reading indicates an

open voice coil, meaning the compression driver must be replaced. A significantly lower

reading indicates a voice coil that is shorting, meaning the compression driver must be re-

placed.

3. Test the PTP (Power Tracking Protection) network: Place one test lead securely on each of

the GREEN test points on the Access Card. A properly functioning PTP will read no more

than 2 ohms (See Figure 5). If the reading is higher, replace the SK-3 lamps on the cross-

over PCB.

4. Unplug the Access Card and re-install the switch card in exactly the same position it was in

originally. If applicable, Re-attach the security cover, gland nut cover, or NL4 cover.

Figure 3:

EVF/EVH Woofer Test

Figure 4:

EVF/EVH Compression

Driver Test

Figure 5:

EVF/EVH Protection

Network Test



 Experienced technicians may perform more

sophisticated tests by connecting specialized test gear in place of the ohm meter.









Note: EVF low-frequency systems have no PTP or compression drivers, and use different woof-

ers. See the chart on page 4 for correct DCR values.

5.0 4.3 1.1

For EVA passive full-range systems:

Use only the test points on the BLACK side of the Access Card

Note the position of the HF shading switch card. The card must be replaced in exactly the

same position as it was originally or system performance will be adversely affected!

EVA components are wired in pairs. Therefore, both woofers will be tested together at the

same time, as will the upper HF compression driver pair and the lower HF compression driver

pair. Each HF compression driver pair has its own PTP network and these are also tested

separately. EVA DCR values are referenced to the black (common) test point (See Figure 6).

To directly access transducer pairs for more sophisticated testing, substitute the (-) input con-

nection on the input terminal block for the black (common) test point on the access card (See

Figure 9). Note: DCR values listed are not valid for this connection.

1. Test the woofers: Place one test lead securely on the RED test point and the other on the

BLACK (common) test point on the Access Card. A properly functioning woofer pair will

read approximately 43.2 ohms DCR, ±1 ohm (See Figure 6). A significantly higher reading

indicates one of the woofers has an open voice coil, meaning the woofer needs to be re-

placed. A significantly lower reading indicates one or both of the woofers has a voice coil

that is shorting, meaning the woofer(s) must be replaced.

2. Test the compression driver pairs: Test the upper compression driver pair by placing one

test lead securely on the UPPER YELLOW test point and the other on the BLACK (com-

mon) test point on the Access Card. A properly functioning compression driver pair will

read approximately 41.6 ohms DCR, ±1 ohm (See Figure 7a). A significantly higher reading

indicates one of the compression drivers has an open voice coil, meaning the compres-

sion driver(s) must be replaced. A significantly lower reading indicates one or both of the

compression driver voice coils are shorting, meaning the compression driver(s) must be

replaced. Test the lower compression driver pair by repeating the above test with the meter

connected to the LOWER YELLOW test point (See Figure 7b).

Figure 6:

EVA Woofer Pair Test

Figure 7a:

EVA Upper Compression

Driver Pair Test

Figure 7b:

EVA Lower Compression

Driver Pair Test

43.2 41.6 41.6

Product specificaties

Merk:	Electro-Voice
Categorie:	Niet gecategoriseerd
Model:	EVI-AC

Heb je hulp nodig?

Als je hulp nodig hebt met Electro-Voice EVI-AC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Electro-Voice

Electro-Voice EVU-TK60 Handleiding

8 Januari 2025

Electro-Voice N/D468 Handleiding

8 Januari 2025

Electro-Voice EVI-AC Handleiding

8 Januari 2025

Electro-Voice MP1-8209 B Handleiding

8 Januari 2025

Electro-Voice N/D868 Handleiding

8 Januari 2025

Electro-Voice EVA-SG2 Handleiding

8 Januari 2025

Electro-Voice XLC-BGK Handleiding

8 Januari 2025

Electro-Voice MA-606 Handleiding

8 Januari 2025

Electro-Voice TR-P Handleiding

8 Januari 2025

Electro-Voice XGS-3 Handleiding

8 Januari 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

MSI Radeon RX 5700 XT EVOKE Handleiding

9 Januari 2025

MSI Radeon RX 6750 XT MECH 2X 12G V1 Handleiding

9 Januari 2025

MSI Radeon RX 6800 GAMING TRIO 16G Handleiding

9 Januari 2025

MSI Radeon RX 6700 XT 12G Handleiding

9 Januari 2025

MSI GeForce RTX 3080 SEA HAWK X 10G LHR Handleiding

9 Januari 2025

MSI GeForce RTX 4060 Ti 8G GAMING SLIM MONSTER HUNTER EDITION Handleiding

9 Januari 2025

AOpen WT15M-FI Handleiding

9 Januari 2025

AOpen WT15M-FB Handleiding

9 Januari 2025

AOpen WT15M-FKB Handleiding

9 Januari 2025

MSI GeForce RTX 4070 VENTUS 2X E 12G Handleiding

9 Januari 2025