Ei Electronics Ei413RF Handleiding

Ei Electronics Niet gecategoriseerd Ei413RF

Lees hieronder de 📖 handleiding in het Nederlandse voor Ei Electronics Ei413RF (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 253 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

RADIOLINK PANEL MODULE

Model: Ei413

RadioLINK Smoke Alarms & Accessories can be

connected wirelessly to Security & Fire Panels

• Powered by 11 - 30VDC from panel

• Can be mounted internally or externally to the panel

• Provides relay outputs (NC, C, NO) from

- Smoke Alarms sensing re

- Alarm fault (Low Battery or Contaminated Chamber)

- CO Alarm sensing CO

• Panel can trigger all smoke / CO alarms to sound

• Unique house coding feature

• Blue LED to facilitate house coding and visual RF transmission

indication

• RF performance to EN300 220-1 in accordance with EN300

220-2

• EMC performance to EN301 489-1 referencing EN301 489-3

• 5 year guarantee

House Code Switch

Blue Light

RF Indicator

Security Panel Installation

The Ei413 can be installed in or next to the panel. If the panel

is in a metal case, then the module should be located on the

outside of the panel.

CAUTION!

Before connecting the Ei413 to a re or security panel please

check with the panel manufacturer to determine the correct End

of Line (EOL) device(s) to use and how and where they should

be tted.

PANEL

FIRE RELAY

Alarm In

ANTENNA

Vin

}

RadioLINK

Alarms &

Controls

CO RELAY FAULT RELAY

Voltage eeFr

Contact Input

Voltage eeFr

Contact Input

Voltage eeFr

Contact Input

Dry ntactCo

12V DC

11-30VDC Supply

Security Panel Wiring Diagram

Check with the panel manufacturers installation manual for

wiring and termination details before proceeding:

1. Each relay of the Ei413 panel module, where used, is wired

to a corresponding contact input in the panel.

2. Check that the sliding jumper link J1 (yellow) is in the off

position. This is the factory default setting.

3. Locate the auxiliary power output in the panel and wire

it to the Vin connector on the Ei413 panel module, being

careful to ensure the polarity of the auxiliary power supply

has been wired correctly.

4. The “Alarm in” signal is optional and can be triggered by an

11 - 30V DC or a dry contact signal from the panel. When

this signal is activated the Ei413 will send out an RF Fire

signal which will activate any RadioLINK alarms or devices

that are in the same housecode.

Fire Panel Installation

CAUTION!

In this application the Fire and Fault relays are being congured

to allow the re panel to indicate a re or fault condition. The

wiring details and end of line (EOL) termination details will

change for different re panels so it is imperitive that you check

the panel manufacturers installation manual before proceeding.

Operation

1. When the Ei413 receives a re signal it will create a short

circuit across the Detector Zone Input, resulting in a re

indication on the panel. A current limiting resistor may be

required so check the panel manufacturers installation

manual.

2. When the Ei413 receives a fault signal it will open circuit

the connection to the Detector Zone Input, resulting in a

fault indication on the panel.

3. A re signal will override a fault signal .

Installation

1. Slide the jumper link J1 (yellow) to the on position. The

factory default setting is off.

2. Locate the auxiliary power output in the panel and wire it to

the Vin connector on the Ei413 panel module.

3. Check that the polarity of the auxiliary power supply has

been wired correctly.

4. Wire the Fault Relay common (C) terminal and the Fire

Relay common (C) terminal to a detector circuit in the

panel.

5. Wire the manufacturers End of Line (EOL) device according

to the re panel installation manual.

6. Power up the re panel and the Ei413 panel module and

follow the manufacturers instructions to set up the re

panel system.

Product specificaties

Merk:	Ei Electronics
Categorie:	Niet gecategoriseerd
Model:	Ei413RF
Kleur van het product:	Wit
Gewicht:	190 g
Breedte:	88 mm
Diepte:	88 mm
Hoogte:	42 mm
Gewicht verpakking:	210 g
LED-indicatoren:	Ja
Ingangsspanning:	11 - 30 V
Temperatuur bij opslag:	0 - 35 °C
Bedrijfstemperatuur (T-T):	0 - 40 °C
RF Zendbereik:	100 m
RF-zendfrequentie:	868.499 MHz