Ei Electronics Ei 410 Handleiding

Ei Electronics Afstandsbediening Ei 410

Lees hieronder de 📖 handleiding in het Nederlandse voor Ei Electronics Ei 410 (2 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 52 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

TEST

RED

LIGHT UPPER

LOWER

The Ei410T Remote Control is an excellent accessory to

help you manage and maintain your Alarms. It is

designed for use with the SmartTest range of Alarms

(models: Ei3100RF, Ei3103RF & Ei3105RF).

The Remote Control is used to test the alarms from a

distance. There is therefore no need for chairs, ladders or

poles to help you reach the alarms test button.

INSTALLATION

1. For ease of installation, the Remote Control is supplied

with the battery connected and ready to use.

2. Press the Test button on the Remote Control until the

red light comes on. The red light indicates a radio

frequency (RF) signal is being sent. (If this does not work,

remove the battery (see Figure 1(a)), hold down the Test

button for 10 seconds and then re-install the battery). The

Alarms should respond within 20 seconds once they are

within range (typically the range is over 10 metres indoors

but this will depend on the type of walls etc.).

3. As with all SmartTest products, it is essential that you

House Code your Remote Control with your Alarms to

prevent false alarms and other interference with nearby

systems (see overleaf).

House Coding the Ei410T Remote Control

Some of the SmartTest products can transmit and receive

over 150 metres (in free space) so it is important to

ensure neighbouring systems do not interfere with your

system and vice versa.

FIVE YEAR GUARANTEE (Limited)

Ei Electronics guarantees this product (excluding the

battery) against any defects that are due to faulty material

or workmanship for a five year period after the original

date of purchase. This guarantee only applies to normal

conditions of use and service, and does not include

damage resulting from accident, neglect, misuse unau-

thorized dismantling or contamination howsoever

caused. If this product has become defective it must be

returned to one of the addresses below (see "Getting

Your Remote Control Serviced") with proof of purchase.

If the product has become defective during the five year

guarantee period the unit will be repaired or replaced

without charge. This guarantee excludes incidental and

consequential damages.

Do not interfere with the product or attempt to tamper with

it. This will invalidate the guarantee.

Ei Electronics

Shannon Industrial Estate,

Shannon, Co. Clare, Ireland.

Telephone: +353 (0)61 471277

www.eielectronics.com

Smoke/Heat Alarm

Remote Control

Model: Ei410T

The following procedure will House Code your Remote

Control with your SmartTest Alarms. After the House

Coding procedure, the SmartTest Alarms and the Remote

Control will only communicate with other units House

Coded at the same time.

1. Place all the SmartTest Alarms into House Code mode,

within 10 minutes, by pressing their House Code buttons,

as described in their instruction leaflets.

2. Also, within the same 10 minutes, place the Ei410T

Remote Control into House Code mode by pressing and

holding the “Upper & Lower” buttons (see Figure 1(b))

simultaneously until the red light turns on. Release the

buttons and the red light will now flash continuously (for

15 minutes) to show it is in House Code mode.

3. The Remote Control will now send a House Coded

radio message every 5 seconds with its House Code

serial number. All Alarms within range, that are also in

House Code mode themselves, will memorise the House

Code serial number of the Remote Control.

Note: It may be necessary to move around the property

with the Remote Control to ensure that all Alarms have

received the signal.

4. Check that the number of amber light flashes (for

SmartTest Alarms) corresponds with the number of units

in the system (i.e. Alarms plus Remote Control). For

example, with 3 SmartTest Alarms and 1 Remote Control

you should see 4 light flashes from each Alarm.

5. Remove all the SmartTest Alarms from House Code

mode as described in their instruction leaflets.

6. Remove the Remote Control from House Code mode

by pressing and holding the “Upper & Lower” buttons

simultaneously until the red light comes on constantly

(i.e. the same method as used to enter House Code

mode). Release the buttons and the red light will no

longer flash, indicating that the Remote Control has

exited House Code mode.

(Alternatively, the Remote Control will exit the House

Code mode by itself after 15 minutes without further user

intervention. However, this could result in problems with

nearby systems if their units are being House Coded at

the same time).

7. Finally, test each Alarm with the Remote Control and

verify that the Remote Control activates it.

If some or all of the Alarms are not activated by the

Remote Control repeat the House Code procedure again.

Clearing the House Codes

It may be necessary at some stage to clear the House Codes (e.g. if

you wanted to use the Remote Control with different un-coded

alarms).

To clear the House Codes:

Hold all three buttons down together, until the red light comes on and

then release. This may take up to 10 seconds.

Note: clearing the House Codes will now reset the Remote Control to

the original factory setting. It will now only communicate with un-

coded Alarms.

Manual Testing with Remote Control Ei410T

Press the Test button on the Remote Control. The red

light will come on to indicate it is transmitting an RF

signal. Then:

• the units will alarm within 20 seconds.

We recommend that you manually test your alarms

weekly using your Ei410T Remote Control.

Battery Replacement

The battery will normally last for 10 years. If it fails to

communicate with the Alarms and/or the red light looks

dim or does not light when a button is pressed, the battery

is depleted and must be replaced.

Slide cover back (as shown in Figure 1) and remove the

battery. Press the Test button for 10 seconds and then

replace with a new Lithium 3 Volt Cell type DL2032 or

CR2032. Ensure battery orientation is correct as shown

in Figure 1(b).

Getting your Remote Control Serviced

If your Remote Control fails to work after you have read

this leaflet contact Customer Assistance at the nearest

address given at the end of this leaflet. If it needs to be

returned for repair or replacement put it in a padded box

with the battery disconnected. Send it to "Customer

Assistance and Information" at the nearest address given

on Remote Control or in this leaflet. State the nature of

the fault, where the Remote Control was purchased and

the date of purchase.

Note: It may be necessary, sometimes, to return a

Smoke/Heat Alarm (see Smoke/Heat Alarm instruction

leaflet) along with the Remote Control, if you cannot

establish which may be faulty.

P/N A16476 Rev0

Figure 1(a) Figure 1(b)

1 2 34

0889

The crossed out wheelie bin symbol that is on your

product indicates that this product should not be disposed

of via the normal household waste stream. Proper

disposal will prevent possible harm to the environment or

to human health. When disposing of this product please

separate it from other waste streams to ensure that it can

be recycled in an environmentally sound manner. For

more details on collection and proper disposal, please

contact your local government office or the retailer where

you purchased this product.

Product specificaties

Merk:	Ei Electronics
Categorie:	Afstandsbediening
Model:	Ei 410
Kleur van het product:	Zwart
Ingebouwd display:	Nee
Gewicht:	32 g
Breedte:	85 mm
Diepte:	37 mm
Hoogte:	12 mm
LED-indicatoren:	Ja
Frequentieband:	0.868 GHz
Accu/Batterij voltage:	3 V
Interface:	RF Draadloos
Batterij bijna leeg-indicatie:	Ja
Merkcompatibiliteit:	Ei Electronics
Aantal knoppen:	3
Maximumbereik:	10 m
Backlight toetsen:	Nee
Oplaadbaar:	Nee
Input type:	Drukknopen
juiste gebruik afstandsbediening:	Beveiligingssysteem
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	15 - 95 procent
Batterijtechnologie:	Lithium
Number of devices supported:	12