Ednet 91610 Handleiding

Ednet Lamineersysteem 91610

Lees hieronder de 📖 handleiding in het Nederlandse voor Ednet 91610 (4 pagina's) in de categorie Lamineersysteem. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Laminator, A4

Manual

91610

The laminator is only suitable for laminating documents. Any other use or modification shall

be deemed to be improper and involves substantial risk of accidents.

Important advice about safety

1. Read through these operating instructions carefully and completely before using the

machine for the first time.

2. Only put the machine on a flat and dry surface. It must be freely accessible from all sides.

It is not recommended to use an extension cable!

3. Do not open or repair the laminating machine yourself but take it to your specialized

dealer whenever it is damaged, or contact our service hot line.

4. Only use films of the correct size (up to DIN A4 max.) and thickness (80 to 100 microns).

Films that are too thin cause a blockage of the film in the machine.

5. Do not touch the hot surface of the machine after it has started up.

6. The laminating machine is not allowed - for safety reasons - to be used by children,

unless they are supervised by an adult.

7. Never use the machine outdoor or near water.

8. Hot lamination: do not laminate in this mode any materials that are sensitive to heat

with this machine, like thermo-fax paper for example. These materials are only suitable

for cold lamination.

9. Do not pour or spill any liquid into the machine or onto it.

10. Do not insert any metal objects into the machine. Please do not grasp inside the

machine with your fingers.

11. The laminating machine is unsuitable for constant use commercially. It is recommended

to switch “O” the machine for 30 minutes, after it has been operating for a period of

approximately 30 minutes.

12. The socket should be near the device and easily accessible.

Starting up the laminating machine

1. Push the plug into the mains socket outlet and set the switch to ‘I’. The red LED (Power)

lights up and the heating process will begin.

2. The green LED (Ready) lights up after approximately 3 - 5 minutes. Now you can begin

the laminating process.

3. Open the laminating film and lay the material that is to be laminated directly onto the

closed side. Leave a margin of between 3 mm and 5 mm approximately beyond the

edges while doing so.

Caution

a) Choose a film of correspondingly suitable size in relation to the material that is to be

laminated respectively.

b) It is not recommended to process several smaller materials in one film.

c) Do not cut up the film before the laminating is done.

d) The material that is to be laminated, is not allowed to be thicker than 0.5 mm

including the film.

e) It is imperative to only laminate very thin or soft materials, like newspaper or

serviettes for example, with thicker films (100 microns). We recommend refraining

from any attempt to do so!

f) Do not insert any laminating film without the contents.

g) Never utilize laminating pockets on one side or when they are rolled up.

h) Only utilize laminating foils that are also described as such. Other kinds of film, like

transparent wallets for example, are unsuitable for laminating!

4. Insert the material within the laminating film straight and with the closed side first into

the feed opening on the machine’s front side. The material will feed it in automatically

now.

5. The laminated material that emerges from the delivery opening on the machine’s back

side is not allowed to be pulled out by force. Wait until it has run out of the machine

completely. Let the laminated material to cool down briefly!

6. Switch off the machine after the laminating has ended, by setting the switch to ‘O’. Let

the machine cool down and always pull the plug out of the mains socket outlet after

using the machine.

Note: Do not feed the laminator further with foil in case of a blockage. Turn off the device

immediately!

Clearing a blockage of the film

1. This machine is equipped with a film blockage function in order to resolve any

blockage of the film. Such function is featured by ABS button on BACK SIDE of the

laminator.

2. Please switch off the machine immediately by setting the switch to “O” and pull out

the plug from the mains socket outlet, let the machine to cool down briefly (for hot

laminating) and push the ‘ABS’ anti-film blockage button on back as direction

indicated by the arrow sign, whenever there is a blockage of the film.

3. Hold the ABS switch firmly with one hand and pull out the film completely from the

machine’s feed opening or delivery opening with the other hand.

4. After you have resolved the blockage of the film and released the ABS switch, this will

go back to its starting position again. Now you can use the machine again completely.

5. Please contact our service hot line if there is a blockage of the film again.

Cleaning and care

1. Please pull out the plug from the mains socket outlet always, in order to clean the

machine. Take care while doing so that the plug does not come into contact with any

liquids.

2. Allow the machine to cool down before cleaning it.

3. Clean the machine with a slighly moist, soft cloth. Do not use any caustic or abrasive

cleaning agents while doing so.

Package:

Laminator

Instruction manual

Technical data

Mains voltage (V) 220-240VAC 50Hz 1.3A

Consumption 310W

Laminating width 240 mm

Size of the machine (mm) ca. 355 x 135 x 58 mm

Film of utilizable thickness 80 - 125 microns

Heating up time 3 min. approx..

Speed 400 mm/min

Product specificaties

Merk:	Ednet
Categorie:	Lamineersysteem
Model:	91610
Soort bediening:	Knoppen
Kleur van het product:	Wit
Ingebouwd display:	Nee
Gewicht:	700 g
Breedte:	355 mm
Diepte:	135 mm
Hoogte:	58 mm
Soort:	Warme lamineermachine
Materiaal behuizing:	Kunststof
Indicatielampje:	Ja
Gebruiksklaar-indicatielampje:	Ja
Gebruiksvriendelijk:	Ja
Opwarmtijd:	3 min
AC-ingangsspanning:	220-240 V
AC-ingangsfrequentie:	50 Hz
Stroomverbruik (typisch):	260 W
Code geharmoniseerd systeem (HS):	84729080
Formaat:	A4
Voorverwarmingstijd:	- min
Lamineersnelheid:	400 mm/min
Maximale lamineerbreedte:	230 mm
Maximale dikte document:	- mm
Maximale dikte folie:	125 µm
Minimale dikte folie:	80 µm