EarthQuaker Devices Disaster Transport SR Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor EarthQuaker Devices Disaster Transport SR (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
<<< English >>>
Hey buddy, welcome to your brand new advanced modulated delay and reverb machine! The
Disaster Transport SR
â„¢ was designed to create an intense wash of lo-îš¿ swirling tape styled echo.
While it may look intimidating at rst glance, it’s actually pretty easy to navigate. The top row of
controls are for delay A and the bottom row of controls are for delay B. Delay A is a 600ms delay
with modulation and delay B is a 300ms delay with reverb. Both delays can be run separately,
in parallel, in series or in series/parallel. To take it one step further, there are also expression
controls for the repeats on delay A as well as bleeding delay A into delay B. The switching was
designed so each delay can be used individually or in tandem with both true bypass or trails.
In addition to being used as a straight delay, straight reverb, rhythmic delay, modulated delay
and old school tape-style echo, the Disaster Transport SR can also be used to create a wide
variety of wild sounds ranging from warped records, clanging ange, smooth chorus, echoed out
squalls and various other-worldly effects that will blow your mind, man.
If you are a fan of old school tape delay and crazy lo-îš¿ sounds, you will get hours of enjoyment
every time you plug into the Disaster Transport SR. If not, you may have just made a huge
mistake. Hand made one at a time in sunny Akron, Ohio USA.
Expression Pedal Control
We recommend the Moog EP-2 expression pedal for use with the Disaster Transport SR.
Control Center
The controls for delay A and B are separated by row. The top row is for delay A and the bottom
row is for delay B.
Delay A Controls
Time: Controls the delay time from about 30ms up to 600ms.
Repeats: Controls how many regenerations of the signal there are. This ranges from one
single repeat through an endless wash into self oscillation. This can also be controlled via an
expression pedal. The Moog EP-2 is recommended.
Mix: Level control for the wet signal. Unity is around center, anything above is boosted. Boosting
this works great when using a distorted signal. Please keep in mind this is a gain control, a bit of
hiss is normal when it’s above unity.
Depth: Controls the intensity of the modulation, from no modulation to all out seasick pitch bends.
Rate: Controls the rate of the modulation. The LED for delay A ashes in time with the modulation
to visually show where the rate is set.
Bleed: This feeds delay A into delay B, post reverb (see block diagram for visual explanation).
Use this control for series or series/parallel operation to create rhythmic repeats, extra long
delay time or an all out echo wash. This can also be controlled via an expression pedal. The
Moog EP-2 is recommended. When using the bleed, experiment with the repeat controls on
each delay line. Try using them in different settings, both together and individually, for different
timing and textures.
Delay B Controls
Reverb: Controls the amount of reverb added to the input of delay B.
Mix: Level control for the wet signal. Unity is around center, anything above is boosted. Boosting
this works great when using a distorted signal. Please keep in mind this is a gain control, a bit of
hiss is normal when it’s above unity.
Repeats: Controls how many regenerations of the signal there are. This ranges from one single
repeat through an endless wash into self oscillation.
Time: Controls the delay time from about 30ms up to 300ms.
O P E R AT I O N M A N U A L
Power
This device take a standard 9 volt DC power supply with a 2.1mm negative center barrel. We
always recommend pedal-speciîš¿c, transformer-isolated wall-wart power supplies or multiple
isolated-output supplies. Pedals will make extra noise if there is ripple or unclean power.
Switching-type power supplies, daisy chains and non-pedal speciîš¿c power supplies do not îš¿lter
dirty power as well and let through unwanted noise. DO NOT RUN AT HIGHER VOLTAGES!
Current Draw: 107mA
Switching
This device is true bypass and uses electronic relay based switching. Audio will not pass without power.
Warranty
This device has a limited lifetime warranty. If it breaks, we will îš¿x it. Should you encounter any
issues, please email info@earthquakerdevices.com.
Visit our YouTube Channel for a Visual Demonstration
http://www.youtube.com/earthquakerdevices
Example Settings
Parallel with no modulation or reverb
Series with no modulation or reverb
Series/parallel with modulation & reverb
Clanging psuedo anger modulation
Disaster
Transport
Disaster
Transport
Disaster
Transport
Disaster
Transport
Switching
The switches for both delays switch the inputs only. The outputs are always connected. This
allows you to have trails by always leaving the bypass switch engaged or to use the bypass
switch as the master on/off for true bypass. Additionally, you can feed delay A in to delay B with
the bleed control without having delay B switched on for a cleaner rhythmic delay.
Jacks & Switching
Signal Flow & Notes
Signal Path Block Diagram Explanation: Delay A and B levels can be adjusted with the Mix
control. Dry signal is always present at unity level. The Bleed control is used to feed the output
of delay A into the input of delay B. If the Bleed control is set anywhere above zero, you will hear
the output of delay B being fed by delay A, regardless if delay B is switched on or off.
Series Operation: Delay A is switched on and set to taste, Delay B is switched off and set to
taste and the Bleed control set to taste.
Parallel Operation: Delay A is switched on and set to taste, Delay B is switched on and set to
taste and the Bleed control is set to zero (no bleed).
Series/Parallel Operation: Delay A is switched on and set to taste, Delay B is switched on and
set to taste and the Bleed control set to taste.
Delay A only: Delay A is switched on and set to taste, the Bleed is set at zero and Delay B is switched off.
Delay B only: Delay A is switched off, the Bleed is set at zero and Delay B is switched on and
set to taste.
Output Jack
9v 2.1 mm DC Power Jack
Repeats Expression Jack
Bleed Expression Jack
Input Jack
Delay A Input Bypass
Master Bypass Switch
Delay B Input Bypass


Product specificaties

Merk: EarthQuaker Devices
Categorie: Niet gecategoriseerd
Model: Disaster Transport SR

Heb je hulp nodig?

Als je hulp nodig hebt met EarthQuaker Devices Disaster Transport SR stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd EarthQuaker Devices

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd