Dual XPA6100 Handleiding

Dual Receiver XPA6100

Lees hieronder de 📖 handleiding in het Nederlandse voor Dual XPA6100 (12 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTALLATION/OWNER S MANUAL’

Mobile Power Amplifiers

XPA SERIES

XPA2100

XPA4100

XPA6100

XPA SERIES INSTALLATION

Preparation

Please read entire manual before installation. Due to the technical nature of amplifiers,

it is highly recommended that your DUAL amplifier is installed by a professional installer

or an authorized dealer.

Before You Start

• Disconnect negative battery terminal. (consult a qualified technician for instructions)

• Avoid installing the amplifier where it would be subject to high temperatures, such as

from direct sunlight, or where it would be subject to dust, dirt or excessive vibration.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• All amplifier installations require power, signal and speaker wires (not included).

• An amplifier installation kit (sold separately) is highly recommended to facilitate the

installation. Consult your dealer for recommendations.

Mounting Location

• Choose a mounting location for the amplifier. Suggested locations include under a seat

or in the trunk.

• The amplifier can be mounted horizontal (recommended) or vertical. For optimum

performance, make sure to provide at least 1" of space to around all sides. Do not

mount the amplifier under carpets or where airflow is restricted.

• Do not install the amplifier where it may be exposed to moisture.

• The optimum mounting location varies between vehicles. Remember to test all

amplifier functions before completing the final mounting procedure.

TYPICAL MOUNTING METHOD

NOTE

Be sure to follow specific instructions included with your amplifier installation kit

(not included with this amplifier). The information below should be used a general

guideline only.

Power Wire (+12V)

• Disconnect negative battery terminal before proceeding. Consult a qualified

technician for instructions if you are unsure.

• Plan wire routing before cutting any wires to length. Begin by routing the power

+12V wire from the battery to the amplifier location. Use a grommet when running

wires through the firewall or metal openings. Avoid running the power wire near

existing vehicle wiring to prevent induced noise from entering the audio system.

• Use extreme caution when drilling holes to avoid damaging fuel lines or existing

vehicle wiring.

• The +12V wire MUST be fused within 18" of the battery for protection of the vehicle’s

electrical system.

Ground Wire (GND)

• The amplifier ground wire should be as short as possible. Choose a clean unpainted

section of metal or the vehicle chassis when attaching the ground connection. Be

sure to clean the area of any dirt or grease.

Remote Turn-on Wire (REM)

• The remote turn-on wire connects to the head unit's amplifier turn-on lead or

power antenna output.

Speaker Wires

• Choose adequate gauge speaker wire depending on your exact amplifier/speaker

combination. Be sure to observe polarity when connecting.

• Do not ground any speaker wires or connect any speaker wires together.

Input Signal

• The amplifier's input signal connects to the head unit's low level (RCA) or high level

(speaker wire) outputs.

• Low level input signal deliver the best performance. If unavailable, use the high

level inputs - when interfacing with factory head unit for instance.

CAUTION

• Do not use both low and high level inputs at the same time - connect only one or

the other.

• Never run any wires underneath or outside the vehicle.

XPA SERIES INSTALLATION

Connection Descriptions

Product specificaties

Merk:	Dual
Categorie:	Receiver
Model:	XPA6100
Kleur van het product:	Rood
Ingebouwd display:	Nee
Breedte:	348 mm
Diepte:	233 mm
Hoogte:	54 mm
Gebruikershandleiding:	Ja
Materiaal behuizing:	Aluminium
LED-indicatoren:	Ja
Connectiviteitstechnologie:	Bedraad
Materiaal:	Aluminium
Bedoeld voor:	Auto
Audio-uitgangskanalen:	1.0 kanalen
Frequentiebereik:	20 - 200 Hz
Signaal/ruis-verhouding:	72 dB
Totale harmonische vervorming (THD):	1 procent
Batterijen inbegrepen:	Nee
Input sensitiviteit:	200 mV
Crossover frequentie:	40 Hz
Piekvermogen per kanaal:	600 W
Speakers connectiviteit type:	RCA
RMS vermogen uitvoer per kanaal (4 Ohm):	200 W
Output impedance:	8 Ohm
RMS vermogen uitvoer per kanaal (2 Ohm):	300 W
Bass boost:	0 - 12 dB
Ingebouwde crossover:	Ja