DSC RM-2 Handleiding

DSC Detector RM-2

Lees hieronder de 📖 handleiding in het Nederlandse voor DSC RM-2 (13 pagina's) in de categorie Detector. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/13

PRM-2W/4W Polarity Reversal Modules

Installation Instructions

Introduction

The PRM series modules are Polarity-Reversal Modules for use with the FSA series of 2

and 4 wire smoke detectors and smoke alarms with integral sounders. These modules

provide a 'Tandem' connection such that when one smoke detector goes into alarm,

all smoke detector horns will sound. When the control panel is initiated into alarm, it

signals the PRM module to reverse the polarity of the power to the connected smoke

detectors. Upon Power Polarity Reversal, all connected smoke detectors will sound

their integral horn.

Specification (refer to Table 1)

Power Supply (Range) ...........................................................................12-15VDC

Current Draw (Standby) ......................... PRM-2W: 30mA max. / PRM-4W: 10mA

Current Draw (In-Alarm) ......................... PRM-2W: 50mA max. / PRM-4W: 25mA

Smoke Loop Alarm Current.................................................................1.0A (max.)

Operating Environment ..... 0°C-49°C/32°F-120°F (5-93% RH, non-condensing)

Models

PRM-2W ................................................................................. 2-wire (board only)

PRM-2WC.................................................................................. 2-wire (enclosed)

PRM-4W ................................................................................. 4-wire (board only)

PRM-4WC.................................................................................. 4-wire (enclosed)

Interconnection of Smoke Detectors

PRM-2W is for use with FSA-210 series 2-wire smoke detectors with integral horns. This

module includes a Class B/Style B 2-wire smoke detector zone which provides an inter-

face for control panels that do not have a compatible 2-wire smoke detector zone.

Connection of the module to the control panel is a typical 4-wire type where a reset-

table power output and a panel fire zone input is provided. The module provides a

N.O. dry contact as the initiating device for the panel fire zone. The module monitors

the Bell output of the panel to determine when a fire alarm has been initiated in the

panel.

When the module detects a temporal pattern, or a pulsing output on the bell circuit,

it will reverse the power to the connected smoke detectors signaling them to sound

their horns. Alternately, the module can be triggered to reverse the polarity with a dry

contact from the control panel or from an external relay contact that is activated by an

output from the control panel (see Fig. 1 for wiring details).

NOTE: This module can be used with FSA-210 series smoke detectors without an integral

horn and thus provide a compatible interface to control panels that do not have a 'com-

patible' 2-wire smoke detector zone. For this application, the Polarity Reversal function

would not be used.

PRM-4W is for use with the FSA-410 series 4-wire smoke detectors with integral horns.

This module requires resettable power from the control panel. The dry contact(s) in the

smoke detectors are wired directly to the fire zone in the control panel.

The module monitors the Bell output of the panel to determine when a fire alarm has

been initiated in the panel. When the module detects a temporal pattern, or a pulsing

output on the bell circuit, it will reverse the power to the connected smoke detectors

signaling them to sound their horns. Alternately, the module can be triggered to re-

verse the polarity with a dry contact from the control panel or from an external relay

contact that is activated by an output from the control panel. 4-wire smoke detectors

require 'power' supervision.

The RM-2 module must be installed beyond the last detector to monitor power to

the detectors. If power fails, the RM-2 will open the detection loop and initiate a

trouble condition in the control panel for that zone (see Fig. 2 for wiring details).

NOTE: The PRM-4W module is also used with the FSA-410(D) series of smoke alarms.

These smoke alarms are only ULC Listed for use in Canada (see Fig. 3 for wiring details).

Installation

Wire module to control panel and smoke detectors (Table 1 and Figure 1, 2 or 3). PRM

modules can be mounted directly in the control panel using the three mounting nylon

standoffs provided. PRM xC modules are equipped with a plastic enclosure for exter-

nal mounting. The plastic enclosure can also be mounted on top of a 2” electrical box

for metal conduit connections. To test the system, activate trigger to verify operation.

Figure 1 - PRM-2W (2-Wire Smoke Detectors)

Maximum operating voltage: 16.40 VDC

Compatibility Identifier: PR200

+12 GND T1 T2 P+ P- C NO EOLR EOLR RL Y1 RLY2

UA398

To Panel

Fire Alarm

Trigger

Bell

Panel EOLR

Relay

Control

Panel

Com

Not Used

A N/O Contact Closure -

If a short circuit is detected at the trigger inputs, the module will reverse

the polarity on the smoke detector loop.

B Bell Circuit Follower -

If a pulsating voltage or temporal pattern is detected at the trigger input T2,

the module will reverse the polarity on the smoke detector loop.

FSA-210

2-Wire Smoke Detector

Refer to Table 1 for all

model names

* *

* Power Limited, Supervised

Input V12-15

/ 1A (max.)

Use a Listed power supply

for protective signalling

systems or a control unit

auxiliary power output. Power

source shall be regulated,

resettable & Power Limited.

2200 Ohm

(Use DSC model EOLR-3)

Trigger Input Options:

To panel

Fire Zone

Class B / Style B

(IDC)

Trigger connections must be in

conduit (20ft max.) and in the same room

{See Note 1}

{See Note 2}

NOTE 1: The drawing above shows a Bell Output with a switched negative. If the Bell Output is a

switched positive, connect the positive [+] terminal to T2.

NOTE 2: It is important that the zone loop on the control panel is current limited, when used with

a 2-wire loop. Ensure the maximum current of the 2-wire loop on the control panel does not exceed

the rating of the PRM-2W (1A@24V

Figure 2 - PRM-4W (4-Wire Smoke Detectors)

+12 GND T1 T2 P+ P

UA398

To Panel

Fire Alarm

Trigger

Bell

Control

Panel

Relay

Com

Not Used

Control Panel

Zone Class B /

Style B (IDC)

(see Note 2)

(Refer to Table 1 for all model names)

FSA-410(S) 4-Wire Smoke

Detectors with Integral Sounder

12V /1ADC

BLK

RED

Panel EOLR

DSC RM-2 Rela y

COM

Refer to the RM-2 Module Installation Instructions for more details

Trigger connections must be in conduit

(20ft max.) and in the same room

* * *Power Limited, Supervised

Input 12 - 15 V

/ 1A (max.)

Use a Listed power supply for

protective signalling systems

or a control unit auxiliary

power output. Power source

shall be regulated, resettable

and Power Limited.

CNO

{Refer to Note 1}

NOTE 1: The drawing above shows a Bell Output with a

switched negative. If the Bell Output is a switched positive,

connect the positive [+] terminal to T2.

NOTE 2: Ensure that the zone loop on the control

panel is current limited, when used with a 2-wire loop.

Ensure the maximum current of the 2-wire loop on

the control panel does not exceed the relay contact

rating of the FSA-410 4-wire Smoke Detector (2A@30V

Product specificaties

Merk:	DSC
Categorie:	Detector
Model:	RM-2
Kleur van het product:	Wit
Breedte:	28.5 mm
Diepte:	86 mm
Hoogte:	21 mm
Stroom:	2 A
Ingangsspanning:	30 V
Merkcompatibiliteit:	DSC
Soort apparaat:	Rookdetector
Type product:	Relaismodule