Drayton MiStat N Handleiding

Drayton Thermostaat MiStat N

Lees hieronder de 📖 handleiding in het Nederlandse voor Drayton MiStat N (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

What is a room thermostat?

... an explanation for householders

A room thermostat simply switches the heating

system on and off as necessary. It works by sensing

the air temperature, switching on the heating when

the air temperature falls below the thermostat setting,

and switching it off once this set temperature has

been reached.

Turning a room thermostat to a higher setting will not

make the room heat up any faster. How quickly the

room heats up depends on the design of the heating

system, for example, the size of boiler and radiators.

Neither does the setting affect how quickly the room

cools down. Turning a room thermostat to a lower

setting will result in the room being controlled at a

lower temperature, and saves energy.

The heating system will not work if a time switch or

programmer has switched it off.

The way to set and use your room thermostat is to

ﬁnd the lowest temperature setting that you are

comfortable with, and then leave it alone to do its job.

The best way to do this is to set the room thermostat

to a low temperature – say 18ºC – and then turn it up

by one degree each day until you are comfortable

with the temperature. You won’t have to adjust the

thermostat further. Any adjustment above this setting

will waste energy and cost you more money.

If your heating system is a boiler with radiators, there

will usually be only one room thermostat to control the

whole house. But you can have different temperatures

in individual rooms by installing thermostatic radiator

valves (TRVs) on individual radiators. If you don’t

have TRVs, you should choose a temperature that is

reasonable for the whole house. If you do have TRVs,

you can choose a slightly higher setting to make

sure that even the coldest room is comfortable, then

prevent any overheating in other rooms by adjusting

the TRVs.

Room thermostats need a free ﬂow of air to sense

the temperature, so they must not be covered by

curtains or blocked by furniture. Nearby electric

ﬁres, televisions, wall or table lamps may prevent the

thermostat from working properly.

MiStatTM N

Room Thermostat

Model: N110R

Invensys

Customer Service Tel: 0845 130 5522

Customer Service Fax: 0845 130 0622

Technical Helpline: 0845 130 7722

Website: www.draytoncontrols.co.uk

E-mail: customer.care@invensys.com

l @DraytonControls

x /DraytonControls

EU Design Regs:- 002180638-1/2/3

User Guide 06490191001 Iss E

MiStat

HOMEOWNER Guide

HOMEOWNER Guide →

Symbol in

display

Function Description

Comfort setting Selects the comfort setting. The pre-set value is used each time when activated,

adjustable within the user settings (see step 3).

Eco setting Selects the Eco setting. The pre-set value is used each time when activated,

adjustable in the user settings (see step 3).

None Home screen Indicates that the pre-set temperatures were changed via +/- key

Step 1: Keys and Display - MiStat

RF Pack: MiStat N110R

→Step 2: +hr (Timer)

Press +hr to start the Timer. The prior used

temperature and time will be displayed and the

temperature will ﬂash.

MiSt at

Press +/- to adjust +hr temperature, then press ( )

to conﬁrm.

Press +/- to adjust +hr period between 0 and 23 hours.

Press ( ) to conﬁrm.

→

Step 3: Additional User Settings

ID Feature: Description: Factory Pre-Set:

1 MAX-TEMP It will not be possible to set a

higher temperature

If MAX-TEMP and MIN-TEMP are set to the

same value, it will not be possible to change

temperature with the +/- keys.

30°C

2 MIN-TEMP It will not be possible to set a

lower temperature 5°C

3 ECO-TEMP ECO Temperature used for energy saving periods e.g. during the night ( ) 16°C

4 COMF-TEMP Comfort Temperature used for comfort periods e.g. during the day ( ) 21°C

DONE Exit from the settings menu to USER-S

To enter User Settings

Press + & – keys for approx. 5

Seconds to enter the settings

menu as shown below.

Press Select ( ) to enter the user

settings.

→

Battery Handling

Batteries, rechargeable or not, should not be disposed

of into ordinary household waste. Instead, they must be

recycled properly to protect the environment and cut down

the waste of precious resources.

Your local waste management authority can supply details

concerning the proper disposal of batteries.

In compliance with the EU Directive 2006/66/EC, the button

cell battery located on the printed circuit board inside the

product, can be removed at the end of the product life, by

professional personnel only.

Step 4: Changing the Batteries

How do I know when to change

the batteries?

When the batteries start to run low a battery icon will

ﬂash in the display to indicate “low battery”, during

this time the MiStat will function normally. When

the battery icon alone is shown in the display, the

batteries are completely exhausted and the MiStat will

cease to function (see below). Re-activate by replacing

the batteries.

How to replace the batteries

Remove the battery covers as shown. Replace the batteries with 2 x 1.5V IEC LR6 (AA) Alkaline bat teries ensuring

correct orientation. Replace the battery covers pressing fully home.

Battery Covers:

Slide outwards

to remove

MiStat Rear

Step 5: Receiver - Key & LED

Lamp

colour

Mode Action Key

Function

Green Normal Call for heat

(boiler is ﬁring)

None

Green

Flashing

Normal RF

communication

None

Off Normal No call for heat

(boiler is not

ﬁring)

None

Red RF loss

or not

bound

No call for heat Switches

the boiler

Amber RF loss

or not

bound

Call for heat Switches the

boiler Of f

LED: See table below for details

Key: See table below for details

MiStat

MiSt at

MiStat

To set a suitable temperature for up to 23 hours, e.g.

for short term absence.

Now the timer is running. The time will be counted

down each hour.

Once the time has elapsed, control returns to the prior

temperature screen.

The Timer can be cancelled by pressing key or by

setting the +hr period to 0.

To exit User Settings

Press + & – keys for approx. 5

seconds to exit.

If there is no key pressed for

2 minutes, the system will exit

the menu, any changes will be

saved.

✎ Troubleshooting:

1Setting temperature values is restricted

aAre Minimum/Maximum temperatures activated?

see Homeowner Guide Step 3.

2NO SIGNAL is visible on the screen, no reaction on

key presses anymore

aIs the receiver powered? (Red signal lamp should

be visible)

3LOCKED is displayed

asee Installation Guide Step 5 - LOCK

MiStat

Current set temperature

Call for heat indication.

This ﬂame will be visible

when the heating

temperature is below

the set temperature.

+hr key: Press to set a

suitable temperature

for up to 23 hours (see

step 2).

Select key: Press

to open and save

editor screens + & - keys:

Press to change

the current

temperature.

Current room temperature

Current Set ting,

see table below

key: Press to toggle

between Comfort

setting, Eco setting and

Home

(Room thermostat only).

See table below.

Customize the controller according to personal requirements.

4Is the battery symbol visible?

aReplace batteries, see Homeowner Guide Step 4.

5STARTING is visible on the screen, no reaction on key

presses anymore

aIs the receiver powered? (Red signal lamp should

be visible)

6WAIT is visible on the screen, no reaction on key

presses anymore

aIs the receiver powered? (Red signal lamp should

be visible)

RF transmission indication. The

RF symbol will be visible as

follows,

Short ﬂashes = RF transmission

Continuous ﬂashing = RF signal

issue

6444 Invensys MiStat N 06490191001 IssE.indd 1 27/09/2013 09:26

1.2m

ID Feature: Description: Factory Pre-Set:

5 BACKLIGHT Available options are: On with timeout (TIMED), Always Off (OFF) TIMED

6 OFFSET Adjust displayed temperature to suit personal needs (-5 to 5°C) 0.0°C

7 LOCK Protect MiStat against unauthorised use. If active, any key press will show LOCKED for a few Secs.

To lock: Enter your 3 digit code for protection.

To unlock: Press +&- key for approx. 5 sec. Enter your 3 digit code

000

Master code 401

8 CTRL-TYPE Conﬁgure the control parameters for the speciﬁc application

9CTRL-ALG Select TPI, TP or On/Off TPI

CYCL-RATE (only shows when CTRL-ALG is TPI

or TP)

Select 6 (GAS) cph (cycles per hour), 12 (ELECtric) cph or 3 (OIL) cph 6 cph

HYST (only shows when CTRL-ALG is On/Off) Select OFF, 0.1 to 5°C (OFF = No temperature hysteresis, even on very low temp. changes, the

relay will switch over according to MIN-OnOFF time)

0.5°C

MIN-OnOFF (only shows when CTRL-ALG is On/Off) Select 1 to 30 minutes (The minimum duration for the relay to be On or Off) 5 min

DONE To exit CTRL-TYPE sub menu

10 VALV-PROT The output will be activated for the speciﬁed time (in Minutes). This will happen weekly, related to

the last actuation of the output. Select OFF, 1 to 10 Minutes.

OFF

11 WIRELESS To create a radio link with the receiver or to view the RF signal qualit y Pre-bound

12 (BIND Press ) key to start connecting to the receiver.

NB. “binding” must also be activated on the receiver, see Step 6 Commissioning

BINDING An RF connection to the receiver will be created. If successful, the SIGNAL level will be displayed.

If unsuccessful, FAILED will be displayed.

13 SIG-LEVEL Indicates the quality of the RF transmission

VERY GOOD, GOOD, POOR, NO SIGNAL

DONE To exit WIRELESS sub menu

15 PROD-INFO View the product details, e.g. Part number, Firmware revision etc. Use ( ) key to show the details

16 RESET Will reset all set tings to factory pre-sets OFF

DONE Exit from the set tings menu to INST-S

INSTALLATION Guide Step 3: Signal Strength

→

The MiStat Room thermostat is prebound to the

MiStat receiver in the factory so they just need

to be positioned in the best place for wireless

communication. To help with this there is a built in

Signal strength indicator, available in the Installer

settings menu on the MiStat thermostat, as shown.

It is recommended that the signal strength is Good

or Very Good to ensure ongoing communication is

maintained.

To enter signal strength menu (see step 5 for more detail))

• Press + & - for approx. 5 secs, then scroll (+/-) to show

INST-S,

• press ( ) to enter the installer menu,

• Press +/- until 11 WIRELESS is shown,

• press to enter, ( )

• press +/- to show 13 SIG-LEVEL as shown,

• press to see the current signal strength.( )

Step 4: Mounting Options Step 5: Installer Settings →

Once the best position has been identiﬁed, the MiStat N

should be ﬁxed to the wall using the wall bracket as

shown.

Customize the MiStat according to application needs.

NB. MiStat can also be positioned using the table

stand included.

Care should be taken to mount the thermostat in a

position which is not subject to direct sunlight or

draughts. Preferably it should be mounted on an inside

wall about 1.2m (4ft) above the ﬂoor in a position where

it can respond to room temperature but away from the

direct inﬂuence of radiators or other appliances giving

off heat.

MiStat

Step 1: Mounting the Wall-plate Step 2: Wiring

! IMPORTANT:

Installation must only be carried out by a

qualiﬁed electrician or heating engineer.

Make sure mains input has a 3 amp fuse.

! CAUTION! Before installation, make sure the

mains supply is switched off!

Option 2: Using an existing wall-plate

Loosen the securing screws on the old receiver

and unplug it. Check that there’s 20mm

clearance to the right of the wall-plate and 25mm

above it. Check the wiring diagram for your

product model to compare terminals and, if

necessary, change the wiring of the wall-plate to

suit. Now plug the MiStat R unit into the

wall-plate and tighten the securing screws.

Check the 3A fuse, and switch on the mains.

Option 1: Fitting a new wall-plate

The ideal location is close to the boiler or central

heating system. For the best performance install

in an open space, at least 30cm distance from any

metal objects including wall boxes and the boiler

housing. It is recommended that the MiStat R is

mounted on the wall nearest the ﬁnal location of

the MiStat N room unit and not less than 30cm

from the boiler side panel.

Loosen the securing screws, remove the wallplate

and, if surface wiring is to be used, snap out

the cable entry strip on the bottom edge of the

wallplate with a pair of pliers. Fix the wallplate,

terminals at the top, either direct onto the ﬂat

wall using wall plugs and no 6 x1” wood screws

or on a plastic ﬂush mounting single conduit box

using M3.5 x 14 screws. Check that there’s 20mm

clearance to the right of the wall-plate and 25mm

above it. Complete the wiring to the MiStat R

wallplate in accordance with the wiring diagram

in step 2, to comply with current IEE regulations.

Place the MiStat R onto the wallplate and tighten

the securing screws.

Check the 3A fuse, and switch on the mains.

Warning: Installing the MiStat R too close to the

metal side panel or mains cables may interfere

with the radio signal.

→ →

Applications

The electronic room thermostat MiStat N can be used

for temperature control together with:

• Boilers

• Oil and gas warm water heating

• Actuators of ﬂoor heating systems or radiators

• Circulating pumps

• Heat pumps

A MiSat R receiver is required for operation.

→

Note: To ensure a properly working heating

system, the menu items in the Installer settings

have to be set according to the needs of the

heating system, see step 5.

Note: To ensure a properly working heating system,

the menu items in Installer settings have to be set

according to the needs of the heating system.

There can be gaps in the ID numbering.

! DO NOT

use a surface

mounting box

This product is double insulated and

does not require an earth connection.

The MiStat R should be wired to the

boiler or central heating wiring using the

correct type of cable or ﬂex. The MiStat

R should be wired to replace hard wired

room or programmable thermostats,

as shown on the system or boiler wiring

diagrams.

Always check other manufacturers

instructions for compatibility.

N L 1 2 3

230V AC 50Hz

Fused 3A

Common heating

satisfied

or call for

cooling

Call for

heat

Volt free contacts

Combi boiler basic wiring layout

Zone control basic wiring layout

Note: If not bound, the bind screen will be visible.

For commissioning see Step 6

Note: Only needed if not already bound, ie if

replacing either the MiStat thermostat or the

MiStat receiver.

To exit Installer Settings

Press +/- until ‘DONE’ is shown, then press ‘Select’ or

press + & – keys for approx. 5 seconds to exit. If there

is no key pressed for 2 Minutes, the system will exit the

menu, any changes will be saved. 1. Turn on power for the receiver. The red lamp will

come on. (if green lamp is visible, the device is

already bound, no further action needed here)

(If a separate programmer/Timer is ﬁtted, ensure

that it is switched on)

2. Push the button for >5 Seconds and the LED will

ﬂash red – yellow – green --- -red – yellow - green…

3. Enter binding mode on the corresponding

MiStat room unit, see Step 5: Installer settings ,

item 11

Important: It is essential, that the binding is

carried out between the corresponding room

unit and the receiver

4. If binding is successful, the signal strength will

be indicated on both the MiStat room unit and

the MiStat receiver as follows. If unsuccessful,

FAILED will be displayed. If POOR SIGNAL

is displayed, look for a better location. If NO

SIGNAL is displayed, try connecting again with

the room unit in a different position.

MiStat Room Unit

MiStat Receiver

Immediately after binding, these signals will indicate

the signal quality for 1 minute.

• three green ﬂashes = Very good signal

• double amber ﬂashes = Good signal

• single red ﬂashes = Poor signal

• steady red = No signal

To check the wireless connection

A green lamp on the receiver will indicate a good RF

connection.

→

To enter Installer Settings

Press + & – keys for approx. 5 Seconds to enter the

settings menu as shown.

Note: If not bound, the bind screen will be visible.

For commisioning see Step 6

Technical DataStep 6: Commissioning

MiStat N110R & MiStat R111M

Supply voltage MiStat N: 2 x A A 1,5V alkaline

bat teries

MiStat R: 230V

Switch rating MiStat R: 2(1)A 230V a.c.

Ambient

temperature

Operating: 0°C to 45°C;

Storage: –20°C to 55°C;

Battery life MiStat N: 2 years (typically)

Temperature

range

5°C to 30°C

Temperature

resolution

0.5 °C, display and setting

Control accuracy <0.6°C at 4°/hour

Wiring Mistat R: Fixed wiring only, to comply

with current IEE regulations (BS7671)

MiStat N: No wiring required

Mounting MiStat R: Industr y standard wallplate

MiStat N: Wall bracket or table stand

Radio frequency 868.3 (Bi-directional communication)

Radio signal range 30m typically. The range may be

affected by the composition / density

and number of walls between the

MiStatN and MiStatR

Pollution degree 2

Software class A

Rated impulse

voltage

MiStat R: 2.5kV

Ball pressure test

temperature

MiStat R: 75°C

Relevant EC

Directives:

2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic

Compatibility Directive

1995/5/EC R&TTE Directive

2006/66/EC Battery Directive

2011/65/EU RoHS Directive

Applied

Standards:

EN60730-1; EN60730-2-9

ETSI EN 300 220-3; ETSI EN 301 489-3

eg. eg.

→

User Code:

MiStat R

N L 1 2 3

L -

N -

Radio signals

to MiStat R - no wiring

tched

230V AC

fused 3A,

Internal

boiler

electronics

External

controls

connections

N L 1 2 3

MiStat R

Switched live

from wiring

centre

Motorised valve

To boiler

and/or

pump

Radio signals

to MiStat R - no wiring

230V AC

fused 3A

If POOR is displayed, look for a better location.

If NO SIGNAL is displayed, try connecting again with

the room unit in a different position.

Caution!

The radio receiver may be installed only by a competent

electrician in compliance with the circuit diagram

enclosed in the top housing cover or in compliance

with these instructions. The current safety regulations

must be observed.

In order to achieve protection class II, adequate

installation measures must be taken.

This radio receiver, which can be installed separately,

is designed exclusively for temperature control in dry

and closed rooms and standard environments. This

electronic device was created according EN60730-1, it

operates according working principle 1C.

It has to be placed in a location where it will be able to

control the room temperature.

6444 Invensys MiStat N 06490191001 IssE.indd 2 27/09/2013 09:26

Product specificaties

Merk:	Drayton
Categorie:	Thermostaat
Model:	MiStat N

Heb je hulp nodig?

Als je hulp nodig hebt met Drayton MiStat N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Drayton

Drayton Digistat RF902 Handleiding

21 Augustus 2024

Drayton Digistat RF901 Handleiding

21 Augustus 2024

Drayton PTS1 Handleiding

21 Augustus 2024

Drayton LP20RF & Digistat+ RF Handleiding

21 Augustus 2024

Drayton Easy 2 Handleiding

21 Augustus 2024

Drayton Digistat+1RF Handleiding

21 Augustus 2024

Drayton Digistat+C RF Handleiding

21 Augustus 2024

Drayton HTS3 Handleiding

21 Augustus 2024

Drayton Digistat 2290B Handleiding

21 Augustus 2024

Drayton Digistat 22902 Handleiding

21 Augustus 2024

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Tru Components TCN4S-24R Handleiding

18 December 2024

Tru Components TK4S-14RC Handleiding

18 December 2024

Tru Components TX4S-14R Handleiding

17 December 2024

Warmup 5iE Handleiding

16 December 2024

Warmup +Kit Handleiding

16 December 2024

Nobo Connect SWT-IZW Handleiding

15 December 2024

Nobo Connect SWT-IZB Handleiding

11 December 2024

Hive Thermostat Handleiding

10 December 2024

GENERAL Life HT15S Handleiding

9 December 2024

GENERAL Life HT15 Handleiding

9 December 2024