Drayton Erie Digistat +3 Handleiding

Drayton Erie Thermostaat Digistat +3

Lees hieronder de 📖 handleiding in het Nederlandse voor Drayton Erie Digistat +3 (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Drayton

Installation Guide

Programmable Room

Thermostat

7 Day (5-2 Day)

Models:

22083 / 22087

Power Supply:

Battery / Mains

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Installation / User Guide 06490044001 (0905)

Drayton

User Guide

Programmable Room

Thermostat

7 Day (5-2 Day)

Models:

22083 / 22087

Power Supply:

Battery / Mains

Invensys Controls Europe

Technical Helpline: +44 (0) 845 130 7722

www.draytoncontrols.co.uk

Installation / User Guide 06490044001 (0905)

Warning

If you do not have the knowledge to install the Digistat+3 safely,

arrange for a competent electrician to install it for you. Wiring

should conform to the current IEE wiring regulations. Isolate

mains supply before removing an existing room thermostat and

fitting Digistat+3.

Digistat+3 programmable room thermostats are double

insulated therefore Neutral and Earth connections are not

required. Unused existing cables should be safely insulated.

Location

Care should be taken to mount the

Digistat+3 on a wall, in a postion

which is not subject to direct

sunlight or draughts. Preferably it

should be mounted on an inside

wall about 1.5M (5ft) above the

floor in a position where it can

respond to room temperature but

away from the direct influence of radiators or other appliances

giving off heat.

Installation

1. Remove the front cover using a flat screwdriver and separate

from back plate (Fig 1).

2. Fix the back plate directly onto the wall using suitable wall

plugs and screws or mount over existing wall box (Fig 2).

3. Complete the wiring according to the connection suggestions

shown in Fig 3. For Basic boiler, Combi boiler and Basic boiler

with zone valve applications Digistat+3 with battery or mains

supply are suitable. For Electric Heat application use

Digistat+3 with mains supply only.

4. Replace the front cover by locating in position and pushing

fully onto the back cover (Fig 4).

5. Remove the battery cover using a coin (Fig 5). Battery model only.

6. Install the 2 AA batteries provided (Fig 6). Battery model only.

7. Replace battery cover (fig 7). Battery model only.

8. The Digistat+3 is now installed and will automatically start to

control the room temperature according to the pre-set

program 1 as shown in the User Guide.

The display shows the correct time and date which is

automatically set together with the actual room temperature.

Your Digistat+3 programmable room

thermostat. (7 day (5-2 Day)

Digistat+3 programmable room thermostat allows you to set

time and temperature periods (up to 6 per day) to suit your own

lifestyle. Once fully installed and powered the Digistat+3 will

automatically set the correct time and in auto mode will control

your heating system according to pre-set program 1 (9 till 5).

The temperature is controlled by sensing air temperature,

switching on the heating when the air temperature falls below

the thermostat setting and switching it off once this set

temperature has been reached.

(Fig 1)

(Fig 2)

How to change the temperature for a short time (Override).

When in Auto mode you can override the existing temperature

setting by pressing + or -. During adjustment the temperature will

flash then stop. The Digistat+3 will now control at this

temperature until the next programmed time/temperature event is

reached, when the Digistat+3 will revert back to Auto mode.

Whilst in temperature override the pointer indicates both Man and

Auto. To exit override press > to return to Auto. (Fig 1) shows

Digistat+3 in override.

How to set a constant room temperature (Manual mode).

Manual mode will allow you to set a temperature, over-riding all

programs, until you exit manual mode. In this mode all pre-set

time temperature events will be disabled.

To enter manual mode press < until the pointer indicates MAN

(Fig 2). The screen will only show the temperature, which can be

adjusted by pressing + or -.

Once you have set the temperature it will flash for 5 seconds and

then stop. The Digistat+3 will now control at this temperature until

you adjust using + or - or exit by pressing > to enter Auto mode.

(Fig 1) (Fig 2)

(Fig 4)

(Fig 6)

(Fig 7)

(Fig 5)

(Fig 3)

TEAR HERE TEAR HERE

How to set my room temperature for my holiday period.

(Holiday Mode)

When going on holiday you can lower the temperature of your

home for the duration of your holiday, but set Digistat+3 to

return to your normal programming ready for your return.

Holiday mode works by counting down the days or hour until

your return.

Time periods of between 1 to 24hr then 1 day to 199 days can

be set.

Example

I am ready to leave for my 2 week (14 day) holiday and would like

the house temperature held at a constant 10.0 ºC during this time

and on my return the house temperature will be already running

at my normal pre-set temperature.

To enter Holiday mode press the < button until the pointer is

indicating HOL (fig 3). The temperature will flash and by pressing

the + or - buttons you can change to the temperature required (

in this example to 10.0 ºC) (Fig 3a).

Then press < again to set the time period.(in this example 14

days) using the + or - buttons. (it would be advisable in this

example to set the time period 1 day less (13 days) to ensure the

house temperature is back to normal on your return). (Fig 3b)

Once you have set your time period the time will flash for 10

seconds and then start the holiday period. To exit the Holiday

mode press either < or > to return to auto mode.

When changing time the display will scroll through Hr (Hours)

1-24 then d (Days) 1-99.

The display will show holiday time period and set temperature.

(Fig 3) (Fig 3a)

(Fig 3b)

(Fig 4) (Fig 5)

Battery Model only.

How do I know when to change the batteries.

When the batteries start to run low a battery icon will blink for

15 seconds every 15 seconds to indicate “low battery” during

this time the Digistat+3 will function normally (see fig 4).

Please replace batteries with (2 x AA 1.5V Alkaline batteries).

After 6 months the Digistat+3 will cease to function and will

permanently display the battery icon and nothing else, shown in

(fig 5).

(Fig 6)

(Fig 8)(Fig 7)

(Fig 10)(Fig 9)

How to change the time, day, month & year.

Digistat+3 comes with a pre-set clock, which also automatically

adjusts for summer/winter time changes. It is activated

automatically on 1st installation. There should be no need to

change these settings, however, should you wish to, it can be

done in clock mode.

To enter clock mode press > to select Day. Select Sunday. Use >

to move through all 6 time/temperature events until the arrow

points to the clock symbol. The time will now flash and can be

adjusted (Fig 7) by pressing + or - then press > to accept and

move to Day.

Change day. (Fig 8).

If you wish to change the day press + or - then press > to accept.

Digistat+3 will move to the next field - month.

Change month. (Fig 9).

If you wish to change the month press + or - then press > to

accept. Digistat+3 will move to the next field - Year.

Change year. (Fig 10).

If you wish to change the year press + or -, then press > to

accept. Digistat+3 will now return to Auto mode.

How to replace the batteries see fig 6.

Remove the battery cover using a coin. Replace the spent

batteries with 2 x AA 1.5V alkaline batteries ensuring correct

orientation. Replace the battery cover pressing fully home.

Display Error code E1 or E2.

When the display shows E1 or E2 this indicates a sensor fault and

your heating system will remain Off. Please contact your installer.

How to select another pre-set time/temperature program.

There are 3 pre-set time/temperature programs already held in

memory as shown, if pre-set program 1 is the best program to

suit your lifestyle do nothing and the Digistat+3 will control to

program 1.

If you would like to select one of the other pre-set programs,

refer to ‘How to change User Options’, Option 3 and select your

preferred program.

06490044001 Digistat+3 27/9/05 11:28 Page 1

Installation Guide – continued

User Guide – continued

What is a programmable room

thermostat?

...an explanation for householders

A programmable room thermostat is both a programmer

and a room thermostat. A programmer allows you to set

‘On’ and ‘Off ’ time periods to suit your own lifestyle. A room

thermostat works by sensing the air temperature, switching

on the heating when the air temperature falls below the

thermostat setting, and switching it off once this set

temperature has been reached.

So, a programmable room thermostat lets you choose what

times you want the heating to be on, and what temperature

it should reach while it is on. It will allow you to select

different temperatures in your home at different times of the

day (and days of the week) to meet your particular needs.

Turning a programmable room thermostat to a higher

setting will not make the room heat up any faster. How

quickly the room heats up depends on the design of the

heating system, for example, the size of boiler and radiators.

Neither does the setting affect how quickly the room cools

down. Turning a programmable room thermostat to a lower

setting will result in the room being controlled at a lower

temperature, and saves energy.

The way to set and use your programmable room

thermostat is to find the lowest temperature settings that

you are comfortable with at the different times you have

chosen, and then leave it alone to do its job. The best way to

do this is to set low temperatures first, say 18C, and then

turn them up by one degree each day until you are

comfortable with the temperatures. You won’t have to adjust

the thermostat further. Any adjustments above these settings

will waste energy and cost you more money.

If your heating system is a boiler with radiators, there will

usually be only one programmable room thermostat to

control the whole house. But you can have different

temperatures in individual rooms by installing thermostatic

radiator valves (TRVs) on individual radiators. If you don’t

have TRVs, you should choose a temperature that is

reasonable for the whole house. If you do have TRVs, you can

choose a slightly higher setting to make sure that even the

coldest room is comfortable, then prevent any overheating in

other rooms by adjusting the TRVs.

The time on the programmer must be correct. Some types

have to be adjusted in spring and autumn at the changes

between Greenwich Mean Time and British Summer Time.

You may be able to temporarily adjust the heating

programme, for example, ‘Override’, ‘Advance’ or ‘Boost’.

These are explained in the manufacturer’s instructions.

Programmable room thermostats need a free flow of air to

sense the temperature, so they must not be covered by

curtains or blocked by furniture. Nearby electric fires,

televisions, wall or table lamps may prevent the thermostat

from working properly.

Hol Man Auto Day

96.5

31.3

137.0

Technical Data

Model 22083 22087

Power supply 2 X AA 1.5V 230V AC 50Hz

alkaline batteries

Battery life 3 years typical –

Switch rating

Heating (switch N.O.) 16(2)A 230 Vac

Switch type SPDT (voltage free contacts)

Min. recommended current 10mA @24Vac (inductive)

Ambient temperature Operating 0°C to 50°C

Storage – 20°C to 85°C

Ambient humidity Operating 25% to 85%

(non condensing). Storage 15% to 95%

Temperature range 0°C to 32°C

Accuracy (between 7°C & 32°C) 0.5°C

Timing resolution 1 minute

Temperature resolution 0.1°C

Rated impulse voltage 2.5KV

Ball pressure test 75°C

Pollution situation Degree 2

Protection level IP30

Wiring: Designed for fixed wiring only,

to comply with IEE wiring regulations

Dimensions

Installer Options.

If you wish to change any of the Installer Options as shown

below, enter the Installer Option Menu from Auto mode by

pressing < and + simultaneously for 5 seconds.

Pressing < and + again for 5 seconds will exit the Menu and

return to Auto mode.

Once the Installer Options screen has been selected (Fig 8), the

< and > buttons allow you to scroll through the Menu (shown

below). The + and - allow you to change values. Once a value

has been changed pressing > before exiting the Menu will save

the new setting. (Fig 9 shows Option 1 OFF).

Access protection lock.

The access protection lock allows the installer to lock the

Digistat+3 so that the user cannot make any adjustments.

The default is OFF mode allowing the users to adjust the

Digistat+3 (see User Guide).

To Lock the Digistat+3 settings enter the Installer Options Menu

(Refer to Installer Option 1) and select On and press > to accept.

Once the Installer Options Menu is exited all buttons will be

locked.

To switch off the Protection Lock enter the Installer Menu and

change to OFF. Press > to accept.

Once the Installer Menu is exited all buttons will be free to adjust.

Freeze protection.

Freeze protection will switch on the heating if the room

temperature falls to 5ºC and will then control the temperature at

7ºC even if the Digistat+3 is in OFF mode.

The freeze protection default is ON.

To switch off the Freeze protection mode enter the Installer

Options Menu (Refer to Installer Options 2) and change to OFF.

Press > to accept.

Low and High Limit set points.

The user temperature set points defaults are High 32ºC and Low

7ºC, to change these limits enter the Installer Options Menu

(Refer to Installer Options 3 & 4).

Intelligent Delayed Start (Energy saving feature).

The Intelligent Delayed Start is an energy saving feature which

automatically reduces the warm up time for the heating system.

As the weather becomes milder, Intelligent Start will delay the

heating start times so that fuel is not wasted bringing the room

up to temperature earlier than necessary.

Note: Intelligent Delayed Start only applies in Auto mode.

Intelligent Delayed Start default is in OFF mode.

To switch on Intelligent Delayed Start enter the Installer Options

Menu (Refer to Installer Options 5).

Note the Intelligent Delayed start option is not suitable for

Hydronic underfloor application.

Ensure Installer option 5 is set to Off before final commissioning

for Hydronic underfloor application.

Valve protection.

In some hydronic heating systems there may be a requirement to

protect the valve by operating it once a day, for a given period

without bringing on the heating system.

If valve protection is selected the valve will be operated for a

period as shown in Valve protection time (mins).

Valve protection time every day at 10.00am.

Valve protection default is OFF.

To enable the valve protection mode enter the Installer Options

Menu (Refer to Installer Option 6)

Valve protection time (mins).

Valve protection time can be set between 1 and 5 minutes

(default 3 minutes)

To change this once a day on time enter the Installer Options

Menu (Refer to Installer Option 7).

(Fig 9)

Installer

Options What is it Select between Default

1 Access protection lock On Off Off

2 Freeze protection On Off On

3 Low limit set point ºC 7 High limit 7

4 High limit set point ºC Low limit 32 32

5 Delayed start

(Energy saving feature) On Off Off

6 Valve protection On Off Off

7 Valve protection time (Mins) 1 5 3

8 Sensor fault function On Off Off

9 Application type 1 0 0

Sensor fault function.

When the display shows an error code (E1) or (E2) this indicates

a sensor fault and the heating system will

remain Off.

(E1) = internal sensor and (E2) = external sensor.

If (E1) is shown the Digistat+3 should be replaced.

If (E2) is shown, first check the external sensor terminal block

connections before replacing the Digistat+3.

Sensor fault function allows you to temporally set the Digistat+3

to cycle the heating system 30% On and 70% Off until you have

replaced the product.

This can be done by entering the installer Option Menu (Option

8) and selecting On. Press > to accept.

To reset to default Off, entering the installer Option Menu

(Option 8) and selecting Off. Press > to accept.

Application type.

Model 22083

(Battery) can be used for radiator or Hydronic underfloor

applications.

In installer Option select:

0 = Radiator.

1 = Hydronic underfloor.

Default 0 = Radiator.

Model 22087

(Mains) can also be used for electric heat applications.

0 = Radiator and electric heat.

1 = Hydronic underfloor.

To change application enter the installer Option Menu and refer

to (Option 9).

Drayton – Digistat+3 7 day 5:2 day Programmable Room

Thermostat

Allowing different programs for weekdays and weekends and

also every day of the week can be programmed differently.

(Fig 8)

TEAR HERE TEAR HERE

(Fig 11) (Fig 12) (Fig 13)

(Fig 14) (Fig 14a)

(Fig 15) (Fig 15a)

Pre-set programs for Digistat+3 7 day 5-2day.

Program 1 (9 till 5) as shown below

Monday to Friday

Events 1 2 3 4 5 6

Time 6:30 8:30 12:00 14:00 16:30 22:30

Temperature C 20.0 16.0 16.0 16.0 21.0 7.0

Saturday and Sunday

Events 1 2 3 4 5 6

Time 7:00 9:00 12:00 14:00 16:00 23:00

Temperature C 20.0 18.0 21.0 18.0 21.0 7.0

Program 2 (Home for lunch)

Monday to Friday

Events 1 2 3 4 5 6

Time 6:30 8:30 12:00 14:00 16:30 22:30

Temperature C 21.0 16.0 21.0 16.0 21.0 10.0

Saturday and Sunday

Events 1 2 3 4 5 6

Time 7:00 9:00 12:00 14:00 16:30 23:00

Temperature C 21.0 18.0 21.0 18.0 21.0 10.0

Program 3 (Home worker)

Monday to Friday

Events 1 2 3 4 5 6

Time 6:00 8:30 12:00 14:00 17:30 22:30

Temperature C 21.0 19.0 21.0 19.0 21.0 16.0

Saturday and Sunday

Events 1 2 3 4 5 6

Time 7:00 9:00 12:00 14:00 16:30 23:00

Temperature C 21.0 18.0 21.0 18.0 21.0 16.0

How to change the pre-set time/temperature program to my

own selection.

Press > to select the day function. Now press + to select the day

or days you wish to change. The days can be selected as blocks or

as individual days (figs 11 to 13).

Fig 11 showing Monday to Friday as one block.

Fig 12 showing Saturday and Sunday as one block.

Fig 13 showing Monday through to Sunday as individual days.

Once you have selected the required day or days, press > to

view the existing time/temperature event (1). (Fig 14) time will

flash. Press > again to view the temperature setting, temperature

will flash. Press > again to view the second time temperature

event (Fig 14a).

When you get to the event you wish to change press + or - to

change the required time, then Press > to accept. Use + or - to

select the required temperature, then > to accept. Digistat+3

will now show the next time/temperature event. To exit press <

or > until you return to Auto mode. If you continue to press > it

will display all the time/temperature events and move to the

next day, finally going to auto.

How to change User Options.

If you wish to change any user options 1 to 8 shown in table 1

they can be accessed from Auto or Man by pressing < and >

simultaneously for 3 seconds. Once you have accessed the user

setting Menu (Fig 15) press > to scroll through selectable

options 1 to 8. The settings for each option can be changed by

pressing + or - as required. Press > to accept the change and

move to the next option. To exit press < and > simultaeously for

3 seconds. Alternatively, not pressing any buttons for 2 mins will

cause the Digistat+3 to return to Auto. (Fig 15a) shows option 1

24 (24 hour clock).

Only selected options which have been accepted by pressing >

will be changed.

How to change from 24hr to 12hr clock (Option 1).

Enter user options, select option 1 and use + and – keys to select

desired option, 12 = 12hr and 24 = 24hr. Press > to accept change.

How to change the default manual set-point temperature

(Option 2).

Enter user options, select option 2 and use + and – keys to set

desired temperature. Press > to accept desired change.

How to change to another predefined program 1, 2 or 3

(Option 3).

Enter user options, select option 3 and use + and – keys to select

desired program 1, 2 or 3. 1 = program 1, 2 = program 2 and

3 = program 3. Press > to accept desired change.

How to change the number of program events per day

(Option 4).

Enter user options, select option 4 and use + and – keys to select

desired option. 2 = 2 time / temp events per day, 4 = 4 time /

temp events per day and 6 = 6 time / temp events per day. Press

> to accept desired change.

How to switch on/off the automatic summer / winter time

change (Option 5).

Twice a year the actual time is automatically changed to keep it in

line with the summer / winter time change. Default setting is On.

If you wish to disable / enable this feature enter user options,

select option 5 and press – or + key to display Off or On as

desired. Press > to accept desired change.

How to change temperature offset (Option 6).

The temperature displayed on the thermostat may not match

that of other temperature measuring devices in the controlled

space, because of its location. The displayed and set

temperature may be offset to bring it in line with other devices.

To adjust the temperature, enter the user options, select option

6. The temperature may be offset by +/- 5 degrees by pressing

the + and – keys. Press > to accept the desired change.

How to restore the built in time temperature programs

(Option 7).

Enter user options, select option 7 and use + and – keys to

select desired option. Off = current programs retained. On =

restore factory program settings. Press > to select the desired

change. Please note enabling this function will lose any user

changes to the preset programs.

How to switch the Digistat+3 and heating system off

(Option 8).

To switch the Digistat+3 and the heating system off you need to

enable the Off function. Enter user options, select option 8 and

use + or – keys to select On to enable the Off function .The

thermostat and heating system will now be Off unless the

temperature in the controlled space falls below 7oC the frost

protection set-point. The LCD will display Off and room

temperature only and the keys will not function. To switch On

the Digistat+3 enter user options select option 8 and use + or –

keys to select Off to disable the Off function. The thermostat

will now regulate the heating system in line with the currently

selected program. Please note this does not effect the operation

of domestic hot water where provided.

User

options What is it Min Max Default

1 Change 12h or 24h clock 12 24 24

2 Change the manual set

point temperature

0C 32 0C 20

3 Change to another

pre-set programme 1 3 1

4 Change the number of

programme events per day 2, 4 or 6 6

5 Switch on/off automatic

summer/winter time change On Off On

6 Change temperature offset

C-5 5 0

7 Restore pre-set programme On Off Off

8 To enable Off function On Off Off

(Table 1)

06490044001 Digistat+3 27/9/05 11:28 Page 2

Product specificaties

Merk:	Drayton Erie
Categorie:	Thermostaat
Model:	Digistat +3

Heb je hulp nodig?

Als je hulp nodig hebt met Drayton Erie Digistat +3 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Thermostaat Drayton Erie

Drayton Erie Digistat 3 Handleiding

13 Augustus 2023

Drayton Erie Digistat + Handleiding

13 Augustus 2023

Drayton Erie Digistat +3 Handleiding

13 Augustus 2023

Drayton Erie Digistat 2 Handleiding

13 Augustus 2023

Drayton Erie Digistat RF2 Handleiding

13 Augustus 2023

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Hager WH27441209C Handleiding

2 December 2024

Hager WH26441207C Handleiding

2 December 2024

Hager WH20441200A Handleiding

2 December 2024

Hager WH26441205C Handleiding

2 December 2024

Hager WH20441200B Handleiding

2 December 2024

Hager WH20441205A Handleiding

2 December 2024

Hager WH20441205B Handleiding

2 December 2024

Hager WH20441203A Handleiding

2 December 2024

Hager WH20441204B Handleiding

2 December 2024

Hager WH20441204A Handleiding

2 December 2024