DPW Design Mix Handleiding

DPW Design Niet gecategoriseerd Mix

Lees hieronder de 📖 handleiding in het Nederlandse voor DPW Design Mix (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Mix
The Mix is a compact 4 channel stereo mixer that also can be set up to be set up to be up to 8
channels of mono with crossfading in 4 groups. It also has a built in soft knee limiter for subtle level
control or harder creative coloring of the sound.
It is designed to be a flexible compact part of your system. As the main mixer for a small system or
you have a few distributed in your bigger system and use one to collect the signals from all of them
sa the main out.
The unit can be used as a utility module for control voltages as well as for audio. It is DC coupled.
Inputs, stereo mode
There are 4 channels of stereo input with volume and pan control.
When using one of the channels with mono in stereo mode you can
connect to either left or right channel. The left and right inputs are
normalled to each other.
All channels have one time amplification (unity gain) when the Vol
knob is turned fully clockwise.
The module is designed to never clip internally but the levels can get
high at the output stage. So the output stage has a controlled nice
sounding round clipping that limits the output to +/- 10V.
Use the output LEDs as a guide to get an output level that doesn't
clip.
The bandwidth of the module in this mode is 150 kHz (-3dB point) so
there is basically no unwanted frequency dependent phase shift in the
audio range.
The extended bandwidth will also make the sound of the mixer very
transparent.
M switches
The M switches (mono) turns the channels left and right input to dual
mono with the Vol knob as a volume for both and the Pan becomes a
mono crossfade between the left and right input.
The M switches affects the channels in two groups. The upper M switch affects channel 1 and 2.
the lower affects channel 3 and 4.
This means that engaging one or two M switches can give you 4 mono with two groups of
crossfade plus two stereo channels or 8 channels of mono with 4 groups of crossfade.
The crossfade can be used as a performance feature to gradually crossfade from one part of your
system to an other or to build more complex voices.
If only one side of a channel is connected, the M switch for that channel is on and Pan is in center
possition you will get a two times amplification of that channel. Can be used for extra boost where
needed.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-M1 Rev B
Lim switch
Lim engages a multiple soft knee limiter on the output stage that brick wall limits the output to +/-
5V (+14 dBV). It is designed to have a very transparent sound if not driven hard.
When Lim is on the amplification on all channels also increases by a factor of two. This means that
unity gain on all channels will be with the Vol knob at the 12 oclock possition.
The limiter can be used to protect equipment connected after the Mix module like non Eurorack
equipment as levels otherwise could get a bit too hot.
The limiter can be used as a creative tool to glue the output mix together.
It can also be used as an effect when driven hard. The reason for the increased amplification when
the limiter is on is for this purpose.
If the whole mix is driven fairly hard through a single limiter like this you will get musical artifacts
that are similar to side-chaining a fast compressor.
LED indication
The LEDs will light up when the outputs are at 5V as a help to get your levels right.
In clean mode a good tip would be to set things up so they flash just a little at the peaks in the
signal. You then know you have headroom to the 10V where the output stage clips.
When Lim is on you can see on the LEDs how hard you are driving the limiter.
Device specs
Module size: 9 hp wide, 30 mm deep with power cable connected.
Input impedance: 200 kohm if both left and right are connected. 100 kohm if only one side is
connected.
Output impedance: 1 kohm
Bandwidth: Clean setting 0 to 150 kHz. With Lim switch on 0 to 21 kHz.
Power requirements: +/-12V. Max power consumption 25 mA
Connect the power cable with the red stripe down towards the -12V marking.
The unit is protected for reverse power.
DPW Design, Häradsvägen 200, 14171 Segeltorp, Sweden
www.dpw.se MAN-M1 Rev B

Product specificaties

Merk: DPW Design
Categorie: Niet gecategoriseerd
Model: Mix

Heb je hulp nodig?

Als je hulp nodig hebt met DPW Design Mix stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd DPW Design

DPW Design

DPW Design Zero 2 Handleiding

15 Augustus 2023
DPW Design

DPW Design Shape Handleiding

15 Augustus 2023
DPW Design

DPW Design Switch Handleiding

15 Augustus 2023
DPW Design

DPW Design Limit Handleiding

15 Augustus 2023
DPW Design

DPW Design AV2 Handleiding

15 Augustus 2023
DPW Design

DPW Design 4-Band Dist Handleiding

15 Augustus 2023
DPW Design

DPW Design Wavefolder Handleiding

15 Augustus 2023
DPW Design

DPW Design Mix Handleiding

15 Augustus 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec

Vitec MGW Diamond-HX OG Handleiding

23 November 2024
Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Electrolux

Electrolux ZS70GL Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Stamos

Stamos S-PLASMA 60U Handleiding

23 November 2024