Doro 2424 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Doro 2424 (2 pagina's) in de categorie Smartphone. Deze handleiding was nuttig voor 162 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
www.doro.com
Insert SD card (optional)
GB
Locate the SD card holder
and gently slide the card
in the holder.
Note! The circuit
boards (metal part) on
the cards must not be
scratched or bent. Try
not to touch the circuits with your ngers.
Use only compable memory cards with
this device. Compable card type: microSD,
microSDHC. Incompable cards may damage
the card itself, the device and corrupt any
data stored on the card.
Insert the baery
Insert the baery by
sliding it into the baery
compartment with the
circuits facing up to the
le. Replace the baery
cover.
3. CALLS
Make a call
1. Enter the phone number. Delete with .Clear
2. Press to dial. Press to cancel Abort
the call.
3. Press to end the call.
Note! For internaonal calls, always use +
before the country code for best operaon.
Press * twice for the internaonal prex +.
Call from the phonebook
1. Press to open the phonebook.Name
2. Use / to scroll through the
phonebook, or quick search by pressing the
key corresponding to the rst leer of the
name.
3. Press Opons âCall, alternavely, press
to dial the selected entry, or press
Back to return to standby.
4. PHONEBOOK
The Phonebook can store 300 entries with 1
phone numbers in each entry.
Add a contact
1. Press Menu âPhonebook â
-New contact- OK â.
2. Enter a Name for the contact, see “Enter
text”. Delete with .Clear
3. Use / to select and Number
enter the phone number.
4. When done, press Save.
Doro 2424
Quick Start Guide
1. Speaker
2. Scroll buons
3. Le selecon buon
4. Call key
5. Speed dial A
6. Speed dial B
7. Internaonal prex/
symbols/*/8
8. Right selecon
buon
9. End call /
Power on/o
10. Camera key
11. Microphone
12. Silent /
Input method/#/9
13. Torch/Camera ash
14. Headset socket
15. Torch key
16. Charging cradle
connectors
17. External display
18. Camera lens
19. Lanyard hold
20. Assistance buon
21. Volume
22. Loudspeaker
23. Charging socket
1. GET STARTED
SIM card, memory card and battery
Remove the baery cover
Be careful not to damage
your ngernails when
you remove the baery
cover. Do not bend or
twist the baery cover
excessively as it may be
damaged.
Insert SIM card (required)
Remove the baery if it
is already installed. Slide
the card under the metal
part, with the gold-col-
oured circuit board facing
down. The cut-o corner
of the card helps you to
place the card, correct placement is indicated
in the compartment.
Note! This device accepts micro SIM or 3FF
SIM card. Use of incompable SIM cards
may damage the card or the device, and may
corrupt data stored on the card.
Charge the phone
CAUTION
Only use baeries, charger and accessories
that have been approved for use with
this parcular model. Connecng other
accessories may be dangerous and may
invalidate the phone’s type approval and
guarantee.
When the baery is running low, is
displayed and a warning signal is heard.
Connect the mains adapter to the wall
socket and to the charging socket .y
Tip: Don’t forget to remove the protecve
plasc lm from the display.
2. GET TO KNOW YOUR PHONE
Turn the phone on and off
1. Press and hold the red buon on the
phone to turn it on/o. Conrm with Yes to
power o.
2. If the SIM card is valid but protected with a
PIN code (Personal Idencaon Number),
PIN is displayed. Enter the PIN code and
press . Delete with .OK Clear
Note! If PIN and PUK codes were not provided
with your SIM card, please contact your
service provider.
Aempts: # shows the number of PIN aempts
le. When no more aempts remain, PIN
blocked is displayed. The SIM card must now
be unlocked with the PUK code (Personal
Unblocking Key).
1. Enter the PUK code and conrm with OK.
2. Enter a new PIN code and conrm with OK.
3. Re-enter the new PIN code and conrm
with .OK
Start-up wizard
When starng the telephone for the rst me,
you can use the start-up wizard to set some
basic sengs.
Tip: You can run the start-up wizard later if
you want.
Step-by-step instructions
In this document the arrow (â) indicates next
acon in the step-by-step instrucons.
To conrm an acon in the phone, press OK.
To select an item, scroll vercally or highlight
the item using / and then press .OK
To scroll horisontally, use * ( ) or 8# ( ).9
Enter text
Press a numerical key repeatedly unl the
desired character is shown. Wait a few
seconds before entering the next character.
Press
* for a list of special characters.
Select the desired character with /
and press to enter it.OK
Use / to move the cursor within the
text.
Press
# to cycle upper case, lower case and
numerals.
Change language, time and date
The default language is determined by the SIM
card.
Receive a call
1. Press to answer, or press Silent to
switch o the ring signal and then Reject
(busy signal).
Alternately, press to reject the call
directly.
2. Press to end the call.
Volume control
Use / to adjust the sound volume
during a call. The volume level is indicated on
the display.
Silent
Silent is a xed prole with keypad tone,
message tone and ring tone disabled, while
vibraon, tasks and alarm are unchanged.
Press and hold # to acvate and to
deacvate silent.
Call options
During a call the so keys ( ) give access to
addional funcons.
Speed dial
Use 29 to speed dial an entry from standby.
Press and hold the corresponding buon to
dial.
Add speed dial numbers
1. Press .Menu âPhonebook â
2. Use / to scroll through the
phonebook, or quick search by pressing the
key corresponding to the rst leer of the
name.
3. â â â Opons Phonebook sengs
Speed dial Set numberâ .
4. Select 2 Editâ and select an entry from
the phonebook.
5. Press OK to conrm.
6. Repeat to add speed dial entries for buons
29.
SOS calls
As long as the phone is switched on, it is always
possible to place an SOS call by entering the
main local emergency number for your present
locaon followed by .
Call history
Received, missed, and dialled calls are saved in
a combined call log. 20 calls of each type can
be stored in the log. For mulple calls related
to the same number, only the most recent call
is saved.
1. Press .
2. Use to scroll through the call log./
= Received call
= Dialled call
= Missed call
3. Press . to dial, or Opons
ICE (In Case of Emergency)
In the event of a trauma, it is crical to have
this informaon as early as possible to increase
the chances of survival. Add ICE contact to
improve your own safety. First responders
can access addional informaon such as
medicaon and next of kin from your phone in
case of an emergency. All elds are oponal,
but the more informaon provided the beer.
Press .Menu âPhonebook âICE
1. Use / to scroll the list of entries.
2. Press Edit to add or edit informaon in each
entry. Delete with .Clear
3. Press when done.Save
5. ASSISTANCE BUTTON
The assistance buon allows easy access to
contact your predened help numbers should
you need help. Make sure that the assistance
funcon is acvated before use and make all
necessary conguraons.Test the applicaon
thoroughly.
Make an assistance call
1. When help is needed, press and hold the
assistance buon for 3 seconds, or press it
twice within 1 second.
The assistance call begins aer a delay of
5 seconds. In this me you can prevent a
possible false alarm by pressing .
2. An assistance text message (SMS) is sent to
all recipients. The rst recipient in the list
is dialled. If the call is not answered within
25 seconds, the next number is dialled.
Dialling is repeated 3 mes or unl the call
is answered, or unl is pressed.
CAUTION
When an assistance call is acvated the phone
is pre-set to handsfree mode. Do not hold
the device near your ear when the handsfree
mode is in use, because the volume may be
extremely loud.
Settings
Press Menu âSengs âAssistance.
6. MESSAGES
Create and send text messages
1. Press Menu âMessages âWrite
message.
2. Write your message.
3. Then press .Opons âTo
4. Select a recipient with Add from Phonebook.
Alternavely, select Enter number to add
recipient manually and press .OK
5. You can modify the recipients by selecng
one and press /Opons âEdit Delete/
Delete all.
6. When done, press Opons .âSend
Create and send picture messages
Both you and the recipient must have sub-
scripons that support picture message. The
sengs for picture message are supplied by
your service provider and can be sent to you
automacally via text message.Press Menu â
Messages MMS â.
1. Write your message.
2. Press Opons âAdd picture:
My pictures to select a le.
Note! To keep best picture quality, send only
one picture per message.
You can also Add sound Add video, , and
Preview MMS using the menu.Opons
3. Press and enter Opons âAdd subject
your subject, then press Done.
4. Press and select select a Opons âTo
recipient with . Add from Phonebook
Alternavely, select Enter recipient to add
recipient manually and press .OK
5. When done, press Opons .âSend
Settings
Press Menu âMessages âMessages â
SMS / MMS.
English
Note! All illustraons are for illustrave
purposes only and may not accurately depict
the actual device. This guide is for reference
only. The actual device and the items supplied,
including but not limited to the colour, size,
and screen layout, may vary depending on
the soware and accessories available in your
region or oered by your service provider.
Supplied accessories provide the best
performance with your phone. Your local Doro
dealer provides addional accessories.
A B
1
8
9
10
6
11
12
20
22
23
16
3
4
5
7
2
15
14
19
21
13
17
18
Doro 2424
DFC-0160 (2041,2051,2061)
QSG
English
QSG_Doro_2424_en_A3(A7)_v20(2041,2051,2061)
7. CAMERA (TAKE PHOTOS)
1. Press shortcut buon
or press .Menu âCamera
2. Press to take the photo.
3. Press Opons to reach more sengs.
4. Press to return to standby.Back
Camera settings
Press Menu âCamera .â â Opons
8. BLUETOOTH®
You can connect wirelesses to other Bluetooth ®
compable devices such as headsets or other
phones.
Important!
When you are not using Bluetooth ® connecv-
ity, turn oAcvate Visibility or . Do not pair
with an unknown device.
Acvate Bluetooth®
1. Press Menu âSengs âConnecviy â
Bluetooth.
2. Press Funcon on/o âOn to acvate.
Search device
1. Press Menu âSengs âConnecviy â
Bluetooth .âMy device
2. Press .Search new
3. Select a device from the list and press Bond
to connect. If Bluetooth® is not enabled,
press Yes to acvate.
4. Press OK to conrm.
9. SOUND & DISPLAY
Tone setup
1. Press Menu âSengs âSound â
Tone setup Ringtone â.
2. Use / to select one of the available
melodies, the melody will be played.
3. Press to discard OK Back to conrm or
changes.
LCD backlight
Customise the display sengs.
1. Press Menu âSengs âPhone setup â
LCD backlight:
Set using Brightness 1-5 * (down) and
# (up), 3 is the default value.
Set using Time 5-60 seconds * (down)
and # (up).
2. Press OK to conrm.
11. TROUBLESHOOTING
Phone cannot be switched on
Baery charge low Connect the power adapter
and charge the baery.
Baery incorrectly installed Check the installaon of the
baery.
Failure to charge the baery
Baery or charger damaged Check the baery and charger.
Baery recharged in tempera-
tures < 0°C or > 40°C
Improve the charging
environment.
Charger incorrectly connected
to phone or power socket
Check the charger
connecons.
PIN code not accepted
Wrong PIN code entered too
many mes
Enter the PUK code to change
the PIN code, or contact the
service provider.
SIM card error
SIM card damaged
Check the condion of the
SIM card. If it is damaged,
contact the service provider.
SIM card incorrectly installed
Check the installaon of the
SIM card. Remove the card
and reinstall it.
SIM card dirty or damp
Wipe the contact surfaces
of the SIM card with a clean
cloth.
Failure to connect to network
SIM card invalid Contact the service provider.
No coverage of GSM service Contact the service provider.
Failure to add a contact
Phonebook memory full Delete contacts to free up
memory.
Failure to set a funcon
Funcon not supported or
subscribed from network Contact the service provider.
12. SAFETY INSTRUCTIONS
WARNING
The unit and the accessories can contain small parts. Keep all of
the equipment out of the reach of small children.
The mains adapter is the disconnect device between the product
and mains power. The mains socket outlet must be close to the
equipment and easily accessible.
Network services and costs
Your device is approved for use on the GSM 900/1800 MHz
networks. To use the device, you need a subscripon with a
service provider.
Using network services may result in trac costs. Some
product features require support from the network, and you
may need to subscribe to them.
Operating environment
Follow the rules and laws that apply wherever you are, and
always turn o the unit whenever its use is prohibited or can
cause interference or hazards. Only use the unit in its normal
user posion.
Parts of the unit are magnec. The unit can aract metal
objects. Do not keep credit cards or other magnec media near
the unit. There is a risk that informaon stored on them can be
erased.
Medical units
The use of equipment that transmits radio signals, for example,
mobile phones, can interfere with insuciently protected
medical equipment. Consult a doctor or the manufacturer
of the equipment to determine if it has adequate protecon
against external radio signals, or if you have any quesons. If
noces have been put up at health care facilies instrucng
you to turn o the unit while you are there, you should comply.
Hospitals and other health care facilies somemes use
equipment that can be sensive to external radio signals.
Implanted medical devices
To avoid potenal interference, manufacturers of implanted
medical devices recommend a minimum separaon of 15 cm
between a wireless device and the medical device. Persons
who have such devices should:
Always keep the wireless device more than 15 cm from the
medical device.
Not carry the wireless device in a breast pocket.
Hold the wireless device to the ear opposite the medical device.
If you have any reason to suspect that interference is taking
place, turn the phone o immediately. If you have any
quesons about using your wireless device with an implanted
medical device, consult your health care provider.
Areas with explosion risk
Always turn o the unit when you are in an area where there
is a risk of explosion. Follow all signs and instrucons. There is
a risk of explosion in places that include areas where you are
normally requested to turn o your car engine. In these areas,
sparks can cause explosion or re which can lead to personal
injury or even death.
Turn o the unit at lling staons, and any other place that has
fuel pumps and auto repair facilies.
Follow the restricons that apply to the use of radio equipment
near places where fuel is stored and sold, chemical factories
and places where blasng is in progress. Areas with risk for
explosion are oen – but not always – clearly marked. This
also applies to below decks on ships; the transport or storage
of chemicals; vehicles that use liquid fuel (such as propane or
butane); areas where the air contains chemicals or parcles,
such as grain, dust or metal powder.
Li-ion battery
This product contains a Li-ion baery. There is a risk of re and
burns if the baery pack is handled improperly.
WARNING
Danger of explosion if baery is incorrectly replaced. To reduce
risk of re or burns, do not disassemble, crush, puncture, short
external contacts, expose to temperature above 60° C (140° F),
or dispose of in re or water. Recycle or dispose of used baeries
according to the local regulaons or reference guide supplied
with your product.
Protect your hearing
WARNING
Excessive exposure to loud sounds can cause
hearing damage.
Exposure to loud sounds while driving may distract
your aenon and cause an accident.
Listen to a headset at a moderate level, and do not hold the
device near your ear when the loudspeaker is in use.
Emergency calls
Important!
Mobile phones use radio signals, the mobile phone network, the
terrestrial network and user-programmed funcons. This means
that connecon cannot be guaranteed in all circumstances.
Therefore, never rely only on a mobile phone for very important
calls such as medical emergencies.
Vehicles
Radio signals can aect electronic systems in motor vehicles
(for example, electronic fuel injecon, ABS brakes, automac
cruise control, air bag systems) that have been incorrectly
installed or are inadequately protected. Contact the manufac-
turer or its representave for more informaon about your
vehicle or any addional equipment.
Do not keep or transport ammable liquids, gases or explosives
together with the unit or its accessories.
For vehicles equipped with air bags: Remember that air bags ll
with air with considerable force. Do not place objects, including
xed or portable radio equipment in the area above the airbag
or the area where it might expand. Serious injuries may be
caused if the mobile phone equipment is incorrectly installed
and the airbag lls with air.
It is prohibited to use the unit in ight. Turn o the unit before
you board a plane. Using wireless telecom units inside a plane
can pose risks to air safety and interfere with telecommunica-
ons. It may also be illegal.
13. CARE AND MAINTENANCE
Your unit is a technically advanced product and should be
treated with the greatest care. Negligence may void the
warranty.
Protect the unit from moisture. Rain/snowfall, moisture and
all types of liquid can contain substances that corrode the
electronic circuits. If the unit gets wet, you should remove the
baery and allow the unit to dry completely before you replace
it.
Do not use or keep the unit in dusty, dirty environments. The
unit’s moving parts and electronic components can be damaged.
Do not keep the unit in warm places. High temperatures can
reduce the lifespan for electronic equipment, damage baeries
and distort or melt certain plascs.
Do not keep the unit in cold places. When the unit warms up
to normal temperature, condensaon can form on the inside
which can damage the electronic circuits.
Do not try to open the unit in any other way than that which is
indicated here.
Do not drop the unit. Do not knock or shake it either. If it is
treated roughly the circuits and precision mechanics can be
broken.
Do not use strong chemicals to clean the unit.
The advice above applies to the unit, baery, mains adapter
and other accessories. If the phone is not working as it should,
please contact the place of purchase for service. Don’t forget
the receipt or a copy of the invoice.
14. WARRANTY
This product is guaranteed for a period of 24 months from
the date of purchase. In the unlikely event of a fault occurring
during this period, please contact the place of purchase. Proof
of purchase is required for any service or support needed
during the guarantee period.
This guarantee will not apply to a fault caused by an accident
or a similar incident or damage, liquid ingress, negligence,
abnormal usage, non-maintenance or any other circumstances
on the user’s part. Furthermore, this guarantee will not apply
to any fault caused by a thunderstorm or any other voltage
uctuaons. As a maer of precauon, we recommend discon-
necng the charger during a thunderstorm.
Baeries are consumables and are not included in any
guarantee. This guarantee does not apply if baeries other
than DORO original baeries are used.
Please note that this is a voluntary manufacturer’s warranty
and provides rights in addion to, and does not aect statutory
rights of end-users.
15. COPYRIGHT AND OTHER NOTICES
© 2017 Doro AB. All rights reserved.
Bluetooth® is a registered trademark of Bluetooth SIG, inc.
eZiType™ is a trademark of Zi Corporaon.
vCard is a trademark of the Internet Mail Consorum.
microSD is a trademark of SD Card Associaon.
The contents of this document are provided “as is”. Except as
required by applicable law, no warranes of any kind, either
express or implied, including, but not limited to, the implied
warranes of merchantability and tness for a parcular
purpose, are made in relaon to the accuracy, reliability or
contents of this document. Doro reserves the right to revise
this document or withdraw it at any me without prior noce.
Other product and company names menoned herein may be
the trademarks of their respecve owners.
Any rights not expressly granted herein are reserved. All other
trademarks are property of their respecve owners.To the
maximum extent permied by applicable law, under no circum-
stances shall Doro or any of its licensors be responsible for any
loss of data or income or any special, incidental, consequenal
or indirect damages howsoever caused.
Doro does not provide a warranty for or take any responsi-
bility for the funconality, content, or end-user support of
third-party apps provided with your device. By using an app,
you acknowledge that the app is provided as is. Doro does
not make any representaons, provide a warranty, or take
any responsibility for the funconality, content, or end-user
support of third-party apps provided with your device.
Content copyright
The unauthorised copying of copyrighted materials is contrary
to the provisions of the Copyright Laws of the United States
and other countries. This device is intended solely for copying
non-copyrighted materials, materials in which you own the
copyright, or materials which you are authorised or legally
permied to copy. If you are uncertain about your right to copy
any material, please contact your legal advisor.
16. TECHNICAL DATA
Specifications
Network bands (MHz)
[maximum radio-frequency
power/dBm]: 2G GSM
900 [33], 1800 [30]
Bluetooth (MHz) [maximum
radio-frequency power/
dBm]:
3.0 (2402 - 2480) [10]
Dimensions: 103 mm x 52 mm x 19 mm
Weight: 92 g (including baery)
Baery: 3,7 V/800 mAh Li-ion baery
Operang ambient
temperature:
Min: 0°C (32°F)
Max: 40°C (104°F)
Charging ambient
temperature:
Min: 0°C (32°F)
Max: 40°C (104°F)
Storage temperature: Min: -20°C (-4°F)
Max: 60°C (140°F)
Specific Absorption Rate (SAR)
This device meets applicable internaonal safety require-
ments for exposure to radio waves. Your mobile device is a
radio transmier and receiver. It is designed not to exceed the
limits for exposure to radio waves (radio frequency electromag-
nec elds) recommended by internaonal guidelines from
the independent scienc organizaon ICNIRP (Internaonal
Commission of Non-Ionizing Radiaon Protecon).
The radio wave exposure guidelines use a unit of measurement
known as the Specic Absorpon Rate, or SAR. The SAR limit
for mobile devices is 2 W/kg averaged over 10 grams of ssue
and include a substanal safety margin designed to assure the
safety of all persons, regardless of age and health.
Tests for SAR are conducted using standard operang posions
with the device transming at its highest cered power level
in all tested frequency bands. The highest SAR values under the
ICNIRP guidelines for this device model are:
Head SAR: 0.873 W/kg
Body SAR: 0.637 W/kg
During normal use, the SAR values for this device are usually
well below the values stated above. This is because, for
purposes of system eciency and to minimize interference
on the network, the output power of your mobile device is
automacally decreased when full power is not needed for the
call. The lower the power output of the device, the lower its
SAR value.
This device meets RF exposure guidelines when used against
the head or when posioned at least 0.5 cm away from the
body. When a carry case, belt clip or other form of device
holder is used for body-worn operaon, it should not contain
metal and should provide at least the above stated separaon
distance from the body.
The World Health Organizaon (WHO) has stated that current
scienc informaon does not indicate the need for any special
precauons when using mobile devices. If you are interested
in reducing your exposure, they recommend you reduce your
usage or use a hands-free accessory to keep the device away
from your head and body.
Correct disposal of this product
(Waste Electrical & Electronic Equipment)
(Applicable in countries with separate collecon
systems)
This marking on the product, accessories or manual
indicates that the product and its electronic accessories
(e.g. charger, headset, USB cable) should not be disposed
of with other household waste. To prevent possible harm to
the environment or human health from uncontrolled waste
disposal, please separate these items from other types of waste
and recycle them responsibly to promote the sustainable reuse
of material resources.
Household users should contact either the retailer where they
purchased this product, or their local government oce, for
details of where and how they can take these items for envi-
ronmentally safe recycling. Business users should contact their
supplier and check the terms and condions of the purchase
contract. This product and its electronic accessories should
not be mixed with other commercial wastes for disposal. This
product is RoHS compliant.
10. ADDITIONAL FUNCTIONS
Alarm
1. Press .Menu âOrganiser âAlarm âOn
2. Enter the alarm me using the keypad and
press OK to conrm.
Single, for a single occurrence
Repeated, for a repeated alarm. Scroll
through the list of days and press or On O
to enable or to disable for each day.
3. When done, press OK.
4. When the alarm goes o a signal will sound.
Press Stop to turn o the alarm or press
Snooze to repeat the alarm aer 9 minutes.
Note! The alarm works even when the phone
is switched o. Do not power on if wireless
phone use is prohibited or when it may cause
interference or danger.
Torch
Slide up to turn on the torch. Slide down
to turn o.
Reset settings
1. Press .Menu âSengs
2. Select to reset the phone Reset sengs
sengs. All the changes that you have
made to the phone sengs will be reset to
default sengs.
3. Enter the phone code and press to reset.OK
Tip: 1234 The default phone code is .
Reset all
1. Press Menu â Organiser â File manager â
Highlight phone â Opons âDetails â.
2. Select Reset all to delete phone sengs
and content such as contacts, number lists
and messages (SIM memory is not aected).
3. Enter the phone code and press to reset.OK
Tip 1234: The default phone code is .
www.doro.com
Correct disposal of batteries in this product
(Applicable in countries with separate collecon
systems)
The marking on the baery, manual or packaging
indicates that the baery in this product should not be
disposed of with other household waste. Where marked,
the chemical symbols Hg, Cd or Pb indicate that the baery
contains mercury, cadmium or lead above the reference levels
in EC Direcve 2006/66. If baeries are not properly disposed
of, these substances can cause harm to human health or the
environment. To protect natural resources and to promote
material reuse, please separate baeries from other types of
waste and recycle them through your local, free baery return
system.
Declaration of Conformity
Hereby, Doro declares that the radio equipment type
DFC-0160 (Doro 2424) is in compliance with Direcves:
2014/53/EU and 2011/65/EU. The full text of the EU
declaraon of conformity is available at the following internet
address: www.doro.com/dofc


Product specificaties

Merk: Doro
Categorie: Smartphone
Model: 2424
Kleur van het product: Rood
Gewicht: 92 g
Breedte: 52 mm
Diepte: 18.5 mm
Hoogte: 103 mm
Soort: Seniorentelefoon
Capaciteit van de accu/batterij: 800 mAh
Bluetooth: Ja
Beeldschermdiagonaal: 2.4 "
Resolutie: 320 x 240 Pixels
Touchscreen: Nee
RAM-capaciteit: 8 MB
Standby time (3G): - uur
SIM-kaart-capaciteit: Single SIM
SIM card type: MicroSIM
Bluetooth-versie: 3.0+HS
2G bands (primary SIM): 900,1800 MHz
Hoofd SAR: 0.625 W/kg
Body SAR: 1.31 W/kg
Locatie positie: Nee
Vormfactor: Clamshell
Resolutie camera achterzijde (numeriek): 3 MP
USB-poort: Nee
Type aansluitplug: 3,5 mm
Compatibele geheugenkaarten: MicroSD (TransFlash)
Abonnementstype: Geen abonnement
SMS: Ja
MMS: Ja
Persoonlijke informatie management: Alarm clock, Calculator, Calendar
Personalisatie: Wallpaper
Microfoon mute: Ja
Luidspreker: Ja
Trilalarm: Ja
Assisted GPS (A-GPS): Nee
Markt positionering: Ouderentelefoon
FM-radio: Ja
Video call: Nee
Ingebouwde flitser: Ja
Gesprekstijd (2G): 8 uur
Inclusief acculader: Ja
vCard: Ja
Camera voorzijde: Nee
Inclusief headset: Ja
Datanetwerk: GPRS, GSM
Type ringtone: Polyfonisch
Camera achterzijde: Ja
Standby time (2G): 285 uur
Extern beeldscherm: Ja
Flash card support: Ja
Capaciteit telefoonboek: 300 entries
Ingebouwde zaklamp: Ja
Aantal polyfone beltonen: 10
Wifi: Nee
Batterijtechnologie: Lithium-Ion (Li-Ion)

Heb je hulp nodig?

Als je hulp nodig hebt met Doro 2424 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Smartphone Doro

Handleiding Smartphone

Nieuwste handleidingen voor Smartphone