Dimplex RXMBS4 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Dimplex RXMBS4 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 184 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Heating Operating Guide
PLEASE READ THIS GUIDE CAREFULLY BEFORE USING YOUR
HEATING SYSTEM
The Wall controller which operates your heating system is split into Zones; the
guide below is an example of which zone applies to which room.
Zone 1 = Living room & Hall = Bedroom Two (if applicable) Zone 3
Zone 2 = Bedroom One = (Spare – not in use) Zone 4
In the heating system reaches the desired temperature set Comfort Mode
by you on the control on the top of the heaters.
In the heating system will not function unless the room Setback Mode
temperature falls beyond an uneconomical point (It uses less energy to keep a
back ground temperature when the room is unoccupied than it does to allow
the dwelling to chill too much). Your heating system will automatically monitor
this for you and adjust, if necessary in the Setback Mode .
Your heaters
Your heating system comprises of two types of heater the “DuoHeat” and the “Panel Heater”
all linked to a “Central Wall Controller”.
Duo Heater
• The DuoHeat provides the majority of the heat you will
require.
• Therefore it may remain hot most of the day from heat
stored when cheap electricity is available.
• The heater intelligently selected the cheapest energy
available, combining both low cost and standard rate
electricity.
• To control the heaters’ temperature press the illuminated
panel – for less heat & + for more.
• Child lock function – this disables the controls to prevent
tampering. Press and hold both – and + buttons for 5
seconds to activate, repeat to cancel (the wall controller
overrides the control on the heater – it is only adjustable
when in the ).Comfort Mode
Wall controller
• The wall Controller provides you with the flexibility to
control the whole heating system from one point
• Should you wish to override the system from the preset
times turn the to select the desired Mode Selector Knob
mode.
• If you are absent for long periods of time i.e a short break
or holiday there is a simple function. This Holiday Mode
function switches the heating system in to a frost protection
mode. In this mode the dwelling is continually monitored,
should the temperature drop below the minimum set level
the system will respond to minimize any potential damage.
To set refer to the instruction on the back page.
• Should you wish to change the pre-set times refer to the
instructions on the back page.
This displays the
current time. Time is
set by selecting
and using the – and
+ buttons to adjust.
Press “OK” to
confirm
This indicates the
current mode for
each zone.
1 bar = Setback
Mode
4 bars = Comfort
Mode
Mode Selector Mark.
Line up the symbol on
the mode selector
knob to the dot to
select mode.
This displays the day of
the week day 1 = Monday.
Adjust in the same way as
the Time. hold down Tip
the – and + buttons to
scroll through time in
greater increments.
Modification Buttons for
adjusting times.
Modification Buttons for
confirming adjustments.
This is also the Holiday
Mode function. Press & hold
for 5 seconds, display shows
“AB01” use the - and +
buttons to select the amount
of days you are away. The
days will automatically count
down and switch back to
Auto Mode for your return.
Should you return earlier
than expected just turn the
mode selector knob to
Comfort Mode and then
back to to Auto Mode
reset.
Trouble Shooting Guide
If you have no heat from your heaters first
check they are switched on both at the wall
and on the heater.
Next make sure the Wall Controller has the
Mode Selector Knob in the correct position
(to test put it in the Comfort Mode).
Remember if the temperature setting on your
DuoHeat is not function or responding it is
likely that the Wall Controller is not in a
Comfort Mode. You can check this by looking
at the display on the Wall Controller you
should see 4 bars lit above the zone indicator,
any other display on the screen would indicate
you are not in Comfort Mode. Remember
when in Auto Mode your system will change
between Comfort Mode & Set Back Mode
depending on the time. It is Pre – set to be in
Comfort Mode between 8AM & 10AM – 3PM
& 9PM. If there is no display on the controller
contact your house manager.
Mode Selector Knob
select to override into
Comfort Mode
select Auto Mode to
run on pre set times
select to override into
Set Back Mode
select to override into
Holiday/Frost
Protection Mode
select to switch
system off
select to adjust clock
and day of the week
select this mode to
change the pre-set
times of operation
Configuration options
for installer use only


Product specificaties

Merk: Dimplex
Categorie: Niet gecategoriseerd
Model: RXMBS4

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex RXMBS4 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dimplex

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd