Dimplex Optiflame 3D GLN20CH3D Handleiding

Dimplex Niet gecategoriseerd Optiflame 3D GLN20CH3D

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex Optiflame 3D GLN20CH3D (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
OPERATING
INSTRUCTION MANUAL
08/54381/0 ISSUE 8 OCN 11935
EN: This product is only suitable for well insulated rooms or occasional use. DE: Dieses Produkt ist nur fĂŒr gut isolierte Bereiche oder
gelegentliche Verwendung geeignet. FR: Ce produit convient uniquement à des endroits bien isolés ou pour un usage occasionnel.
IT: Questo prodotto Ăš adatto solo per spazi ben isolati o per uso occasionale. ES: Este producto sĂłlo es adecuado para espacios
bien aislados o un uso ocasional. NL: Dit product is uitsluitend geschikt voor goed geĂŻsoleerde ruimten of voor sporadisch gebruik.
PL: Produkt ten jest odpowiedni wyƂącznie do dobrze odizolowanych miejsc lub do okazjonalnego uĆŒytku. NO: Dette produktet egner
seg kun for godt isolerte rom eller sporadisk bruk. RO: Acest produs este adecvat exclusiv spaƣiilor bine ventilate sau utilizării ocazionale.
CZ: Tento vĂœrobek je vhodnĂœ pouze do dobƙe izolovanĂœch prostor nebo k pƙíleĆŸitostnĂ©mu pouĆŸitĂ­. DK: Dette produkt er kun egnet til
velisolerede rum eller lejlighedsvis brug. PT: Este produto somente é adequado para espaços bem isolados ou uso ocasional. SE: Denna
produkt Àr endast avsedd för vÀlisolerade utrymmen eller tillfÀllig anvÀndning. FI: TÀmÀ tuote soveltuu ainoastaan hyvin eristettyihin tiloihin
tai satunnaiseen kĂ€yttöön. SK: Tento vĂœrobok je vhodnĂœ len pre dobre izolovanĂ© priestory alebo na občasnĂ© pouĆŸitie. SI: Ta izdelek je
primeren le za dobro izolirane prostore ali za občasno uporabo. HR: Ovaj proizvod je pogodan samo za dobro izolirane prostore ili
povremenu upotrebu. HU: Ez a termék csak jól szigetelt terekhez vagy eseti hasznålatra alkalmas
The product complies with the required Product Safety, Electromagnetic Compatibility
and Environmental Standards. This product is fully compliant with LVD, EMC. RoHs and
EcoDesign Directives.
Dimplex Optiî·ąame 3D Inset Fire
Models: Braemar BMR20, Dumfries DMF20, Glencoe GLN20,
Torridon TRR20, Portree POR20, Skeldon SKL20, Lerwick
LER20.
WARNING: FAILURE TO FOLLOW THESE OPERATING INSTRUCTIONS MAY RESULT IN INJURY
AND/OR DAMAGE.
Please note: The Remote Control is packaged in a red box. The 1 x 3V CR2025 lithium battery is also stored in this box and
must be installed in the remote control before operation.
To install the battery, the remote control must be opened by removing the screw and sliding o󰀹 the access cover, located
at the back. Place the battery into its holder and slide the cover into position, before reassembling the screw.
Operating The Product
Operating Instructions (Remote Control)- See Figure 8
Icon Display Funtion Description
A-Power /
Standby
Press Once to turn the product ‘ON’.
Press a second time to put the product into ‘STANDBY’
(When returning from ‘STANDBY’ mode the product will return to previous settings unless
the product has been unplugged, in which case it will reset to factory settings)
B
‘FLAME EFFECT’ button, this turns the ame effect ON independently of the products
other features.
This Button will change the brightness of the ame effect.
There are 3 brightness settings shown as F1, F2, F3.
Flame
Pulsing
This setting is set by pressing the Flame Up button once more after F3. This will cause the
brightness of the ame effect to cycle randomly, creating a ickering effect.
Off If the ame effect is turned off, but the heater is ON, the display will remain active. The
low heat/high heat/cold blow icon will appear continuously in the display indicating
the heater setting.
CSleep
Timer
Press multiple times to change the ‘SLEEP TIMER’ in 0.5 hr increments from 0.5
hr to 8.0 hr before turning off. The remaining time on the ‘SLEEP TIMER’ displays.
(This icon is in colour)Green
D
‘HEAT’ button cycles the unit sequentially through the 4 settings: LOW HEAT, HIGH HEAT,
COOL BLOW and OFF. The heat setting will be indicated by an icon in the display.
When the ame effect is ‘ON’ the display will turn off after 5 seconds, however if the
heater is being used independently of the ame effect. The low heat or high heat icon
will appear continuously in the display.
Low
Heat
This setting will run the heater at ‘LOW HEAT’ this setting will be indicated by the ‘LOW
HEAT’ icon and the letters ‘LO’ appearing in the display. To adjust the temperature
setting the Temp Down or Temp Up buttons described below must be used.
(This icon is in Colour)Orange
High
Heat
This icon in the display indicates ‘HIGH HEAT’ this setting will be indicated by the ‘HIGH
HEAT’ icon and the letters ‘HI’ appearing in the display. To Adjust the temperature setting
the Temp Down or Temp Up buttons described below must be used.
(This icon is in Colour)Red
Cool
Blow
This icon in the oating display indicates ‘COOL BLOW’ this setting will be indicated by
the ‘COOL BLOW’ icon and the letters ‘CB’ appearing in the display.
(This icon is in Colour)Blue
- Off This switches the heater and blower ‘OFF’, no icon will be displayed in the display. Note
the blower will run for 5-10 seconds after being turned off, this is to ensure the product
cools down safely.
E30 Temp Up
Press multiple times to increase the heater temperature in 2
0C increments. The highest
temperature that can be set 300C.
When High Heat is selected, the letters ‘HH’ appear in the display, this means the heat
will remain ON continusously and is not controlled by the thermostat.
F18 Temp
Down
Press multiple times to lower the heater temperature in 2
0C increments. The lowest
temperature that can be set is180C.
G-Flame
Colour Press to turn ON/OFF the coloured accent within the flame effect.
H-Top-light
Fuel Bed Press to turn ON/OFF the Top light illuminating the fuel bed.
J-
Top-light
Back-
ground
Press to turn ON/OFF the Top-light illuminating the product background.
7
H
A
C
E
J
B
F
G
D
Fig. 8 Fig. 9
11

Product specificaties

Merk: Dimplex
Categorie: Niet gecategoriseerd
Model: Optiflame 3D GLN20CH3D

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex Optiflame 3D GLN20CH3D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Dimplex

Dimplex

Dimplex Optiflame 3D GLN20BR3D Handleiding

15 November 2024
Dimplex

Dimplex GDDEU30 Handleiding

26 Februari 2024
Dimplex

Dimplex ALM20E Handleiding

13 November 2023
Dimplex

Dimplex MZT20E Handleiding

1 Juli 2023
Dimplex

Dimplex MZT20BL-E Handleiding

29 Juni 2023
Dimplex

Dimplex Optiflame 3D BMR20CH3D Handleiding

27 Juni 2023
Dimplex

Dimplex Optiflame 3D BMR20AB3D Handleiding

27 Juni 2023
Dimplex

Dimplex Optiflame 3D BMR20BR3D Handleiding

25 Juni 2023
Dimplex

Dimplex Optiflame 3D GLN20CH3D Handleiding

24 Juni 2023
Dimplex

Dimplex DXTT3 Handleiding

13 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Protector

Protector AS-5030.3 V2 Handleiding

21 December 2024
Sabrent

Sabrent AU-MMCW Handleiding

21 December 2024
Sabrent

Sabrent AU-2X35 Handleiding

21 December 2024
Sabrent

Sabrent CB-RS232 Handleiding

21 December 2024
Owon

Owon 500W Handleiding

21 December 2024
Owon

Owon 300W Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ4-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-RKTQ-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-ROCKET-1TB Handleiding

21 December 2024
Sabrent

Sabrent SB-HTSS Handleiding

21 December 2024