Dimplex RX9913 Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor Dimplex RX9913 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 256 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Installation and
Operating Instructions
Receiver Cassette - Model No. RX9913
General Description
Installation
Dedicating A Zone:
Setting Temperatures:
Manual Override:
Locking the receiver:
General Cleaning
After Sales Service
The RX9913 can be used in RPX, EPX, MFP, GFP and LPP heaters and with a master heater fitted with
the Mains Signalling Transmitter (Part No. RX9912).
They operate by receiving a high frequency signal from the master heater transmitter (RX9912). During set
up receivers are dedicated to only one transmitter so that they cannot be activated by signals from any
other transmitter unit.
1. Using a narrow bladed screwdriver, carefully release the cover from the slot adjacent to the controls
on the heater
2. Insert the receiver fully so that it clicks into position
3. Turn the control knob on the heater to the PROG position (RPX models only)
INSTALLER PLEASE NOTE:
Please mark clearly on the receiver label the number of the zone allocated, if used in a multi zone
application. The RX9913 is rated at 230V.
Firstly read the user instructions for operating with the receiver, following Mains Signalling Transmitter
the steps listed under single or multi-zone programming.
1. When the master programmer starts to flash the EMET message and required
zone number, press the small button (A) for 10 seconds until the indicator neon
(B) flashes.
2. Release and press again, neon indicator will be continuously. ON
For heaters fitted with receivers, set the temperature controls in the normal way.
(Refer to heater instructions).
Turn the control button on the slave heater to the required position (comfort, setback, frost or off). To
cancel override and return to programmed operation, turn back to the PROG position. (RPX models only)
An extra screw is supplied to lock the receiver in place. Lock by piercing the prominent spur on the side of
the heater casing until the screw enters a matching hole in the receiver.
WARNING
BEFORE UNDERTAKING CLEANING WORK ON THE CONTROLLER OR APPLIANCE IMMEDIATELY
DISCONNECT THE ELECTRICITY SUPPLY BY SWITCHING OFF AT THE ADJACENT DOUBLE POLE
SWITCH.
The outside of the appliance should be wiped over with a soft damp cloth and then dried. Do not use
detergents or abrasives.
Your product is guaranteed for one year from the date of purchase. Within this period we undertake to
repair or exchange this product free of charge provided it has been installed and operated in accordance
with these instructions.
Your rights under this guarantee are additional to your statutory rights, which in turn are not affected by this
guarantee. Should you require after sales information or assistance with this product please go to
www.dimplex.co.uk where you will find our self help guide by clicking on “After Sales” or call our helpdesk
on 0845 600 5111 (UK) or 01 842 4833 (R.O.I.).
Spare parts are also available on the website www.dimplex.co.uk
Please do not return a faulty product to us in the first instance. Please retain your receipt as proof of
purchase.
Display
Glen Dimplex UK Ltd
Millbrook House
Grange Drive
Hedge End
Southampton
SO30 2DF
Customer Help Line
Tel: 0845 600 5111
E-mail: customer.services@dimplex.co.uk
Web-site: www.dimplex.co.uk
Republic of Ireland Tel: 01 842 4833
A
B
Neon Indicator
Activate Button
Label to indicate
zone number
Issue 2 08/13


Product specificaties

Merk: Dimplex
Categorie: Niet gecategoriseerd
Model: RX9913

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex RX9913 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dimplex

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd