Dimplex OFX150E Handleiding

Dimplex Niet gecategoriseerd OFX150E

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex OFX150E (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 227 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

Installation and Operating Instructions

OFXE Oil Filled Radiator

(IP20)

08/53951/0 Issue 1

IMPORTANT SAFETY ADVICE

WARNING: The heater should only be

used on a horizontal and stable surface

with the feet securely fitted.

This appliance can be used by children

aged from 8 years and above and

persons with reduced physical, sensory or

mental capabilities or lack of experience

or knowledge if they have been given

supervision or instruction concerning the

use of the appliance in a safe way and

understand the hazards involved. Children

shall not play with the appliance. Cleaning

and user maintenance shall not be made by

children without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided

that it has been placed in its intended normal

operating position and they have been given

supervision or instruction concerning the use

of the appliance in a safe way and understand

the hazards involved. Children aged from 3

years and less than 8 years shall not plug in,

regulate and clean the appliance or perform

user maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present.

WARNING: In order to avoid overheating, do

not cover the heater.

DO NOT use this heater in the immediate

surroundings of a bath, a shower or a

swimming pool.

CAUTION: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through

an external switching device, such as a timer,

or connected to a circuit that is regularly

switched on and off by the utility.

IMPORTANT: If the supply cord is damaged,

it must be replaced by the manufacturer, its

service agent or similarly qualified persons in

order to avoid a hazard.

This heater is filled with a precise quantity

of special oil. Repairs requiring opening of

the oil container are only to be made by the

manufacturer or his service agent who should

be contacted if there is an oil leak.

When scrapping the heater, follow the

regulations concerning the disposal of oil.

WARNING - DO NOT USE THIS APPLIANCE

IN A BATHROOM.

DO NOT COVER THE RADIATOR or place

material or garments on it, or obstruct

the air circulation around the heater, for

example with curtains or furniture, as this

could cause overheating and a fire risk.

DO NOT use the heater if it has been

dropped or damaged, contact our Customer

Helpline for further advice.

DO NOT use the heater if it develops an oil

leak. Unplug the heater and contact your

supplier or our Customer Helpline. If the

heater is tipped over, unplug it and allow

it to cool before standing it back upright.

DO ENSURE that the mains lead cannot be

tripped over.

This Heater must not be located immediately

below a socket-outlet.

DO NOT operate the heater with the mains

lead overhanging the heated surfaces.

The radiator complies with stringent

safety standards but to ensure efficient

operation SURFACES OF THE RADIATOR

WILL BECOME HOT AND CONTACT WITH

THESE AREAS SHOULD BE AVOIDED

THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Electrical Connection

Unpacking

Follow any pack operating instructions carefully. Remove the contents of the carton very carefully. Retain all packaging for future use.

Preparing For Use

The radiator may only be used free standing with the feet fitted

The necessary feet and screws are provided, packed with the radiator.

Free Standing on Feet (see Fig.2)

Never use the radiator free standing without the feet fitted. Lay the radiator on its front on a table or similar and offer each foot up to its mounting

bracket. Place each foot over the attachment bosses and secure it using the screws and washer provided

Stand the radiator on its feet and place it in position ready for use. The heater should always be used on a flat stable surface.

Ensure there is at least 75 mm of clear space around the radiator

Installation

Fig. 1

Fig. 2 Fig. 3

WARNING: This radiator carries a warning ‘DO NOT COVER’ to alert the user to the risk of overheating that exists if the radiator is

accidentally covered

WARNING: THIS APPLIANCE MUST BE EARTHED

This heater must be used on an AC ~ supply only and the voltage marked on the heater must correspond to the supply voltage. This

heater is fitted with a rewirable plug incorporating a a 13 amp fuse. In the event of replacing the fuse in the plug supplied, a 13 amp fuse

approved by ASTA to BS 1362 must be used. If any other type of plug is used, a 13 amp fuse must be fitted in the plug, the adaptor, or at

the distribution board.

IMPORTANT: If the plug is not suitable for your socket, the 13 amp plug should be removed.

Before wiring the appropriate plug, please note that the wires in this mains lead are coloured in accordance with the following code:

GREEN AND YELLOW: EARTH

BLUE: NEUTRAL

BROWN: LIVE

Connect the GREEN AND YELLOW wire to the terminal marked ‘E’ or by the earth symbol, or coloured GREEN or GREEN AND YELLOW.

Connect the BLUE wire to the terminal marked ‘N’ or coloured BLACK

Connect the BROWN wire to the terminal marked ‘L’ or coloured RED

NOTE: Although this heater is manufactured to comply with the relevant safety standards, certain types of carpets could become

discoloured by the temperatures under a portable heater. If you are concerned about this, we recommend that you contact the carpet

manufacturer for guidance. Alternatively, stand the heater on a suitable base to shield the carpet

Model Watts A B

OFX 075E 750 570 683

OFX 100E 1000 840 683

OFX 150E 1500 1105 683

OFX 200E 2000 6831373

A220

Operation

Cleaning and User Maintenance

WARNING: Always disconnect the power supply before cleaning the heater

Do not use detergents, abrasive cleaning powder or polish of any kind on the body of the heater.

Allow the heater to cool, then wipe with a dry cloth to remove dust and a damp cloth (not wet) to clean off stains. Be careful not to allow

moisture in to the heater.

When you have completed the installation, plug in and switch on the power. The neon lamp (see ‘b’ in Fig. 3 & Fig. 4) will light to show that the radiator is powered.

Set the thermostat control knob (see ‘a’ in Fig. 3 & Fig. 4) to the maximum position and allow the radiator to bring the room to your desired temperature.

When the room has reached the desired temperature, turn the thermostat knob anti-clockwise until the thermostat just clicks off. The radiator

will now maintain the chosen temperature.

Note that the radiator may feel cool during operation if the room temperature is higher than the thermostat setting.

When the radiator is not in use, switch off the power supply and pull the plug out from the socket

Model Identifier(s) OFX 075E OFX 100E OFX 150E OFX 200E

Heat output