Dimplex ECOT5FT Handleiding

Dimplex Heater ECOT5FT

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex ECOT5FT (2 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 23 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Model Watt L
1FT 40 158mm
2FT 80 488mm
3FT 120 780mm
4FT 160 1078mm
5FT 200 1340mm
6FT 240 1605mm
Installation Instructions
8/52598/0 Issue 0
Tubular Heater Linking Kit
GDC
1
2
4
3
7
Floor
Wall
39 mm Min.
150 mm
44 mm Min.
L
B
A
1
1
2
2
5
1
1
2
2
6Heater 1
Heater 2
Mains Supply
Alternate Track
Earth: Green and Yellow
Live: Brown Neutral: Blue
C
IMPORTANT: THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE
General
IMPORTANT: The tubular heater must only be installed
in the horizontal plane.
WARNING: It is essential that the product cannot come
into contact with any fabric material.
DO NOT locate the heater immediately below a îš¿xed
socket outlet.
IMPORTANT: The wall brackets supplied with
the appliances must be used. The linking kit and
brackets should be positioned observing the minimum
clearances stated in Fig. 1.
Electrical
WARNING: This appliance must be earthed.
If your tubular heaters are supplied with a plug then the
plugs must be removed to wire the supply cords into
the linking kit. If you cut off the plugs they can constitute
a shock hazard if inserted into a socket outlet. They
must therefore be disposed of safely. The supply cord
provided with the kit can be wired directly into a îš¿xed
wiring outlet or a suitable 13 amp plug can be îš¿tted to it
for connection to a îš¿xed socket outlet.
Before wiring the appropriate plug please note that the
wires in this mains lead are coloured in accordance
with the following code:
GREEN/YELLOW : EARTH
BLUE : NEUTRAL
BROWN : LIVE
Connect the Green/Yellow wire to the terminal marked
‘E’ or the earth symbol ‘ ’ or coloured Green or
Green/Yellow. Connect the Brown wire to the terminal
marked ‘L’ or coloured Red.Connect the Blue wire to
the terminal marked ‘N’ or coloured Black.
DO NOT connect the Brown (Live) or the Blue (Neutral)
wires to the Earth terminal of your 13 amp plug. If the
terminals of the plug are unmarked or you are in any
doubt, consult a qualiîš¿ed electrician.
Product Installation
1. Locate the appliances adjacent to a suitable wall
outlet.
2. Remove the Cover (‘C’ in Fig. 7) from the Linked
End Spacer (‘A’ in Fig. 2) Align the Linked End
Spacer ‘A’ and the Free End Spacer ‘B’ as indicated
in Fig. 2, ensuring that they are level. Space ‘A’ and
‘B’ as indicated in the table and diagram of Fig. 1
(Dimension ‘L’) to suit the model size being linked.
Mark the 6 holes for drilling and set the spacers
aside.
3. After drilling the holes, insert 6 rawl plugs into the
holes. Place the bottom brackets into the spacers,
as shown in Fig. 2, and secure them to the mounting
surface using 4 screws supplied with your heater.
4. Place the îš¿rst heater in position on the brackets
and îš¿x it by locating the top half of each bracket
in the appropriate groove. Slide them down into
position on the bottom half of the brackets and
tighten the îš¿xing screws, as indicated in Fig. 3.
5. Locate the bottom half of the wall mounting brackets,
from your second heater, in the appropriate groove
of the spacers, as shown in Fig. 4. Mark the top 2
holes for drilling then set aside the brackets.
6. Drill the 2 holes and insert rawl plugs into the two
holes. Replace the brackets and secure them to
the mounting surface using the screws supplied
with your second heater.
7. Place the second heater in position on the brackets
and îš¿x it by locating the top half of each bracket in
the appropriate groove. Slide it down into position
on the bottom half of the bracket and tighten the
îš¿xing screws, see Fig. 5.
8. Ensure that the supply cords from both heaters exit
downwards. With both heaters îš¿xed to the wall,
route their supply cords, strip them back and wire
the heater up as shown in Fig. 6. Ensure that the
live wires from the two heaters are stripped and
twisted together before inserting them into the
live terminal block connection and tightening the
terminal screw. Repeat this for the two neutral
wires and the two earth wires. DO NOT connect
the Brown (Live) or the Blue (Neutral) to the Earth
(Green/Yellow). If you are in any doubt consult a
qualiîš¿ed electrician.
9. Fit the Cover (‘C’ Fig. 7) to the Linked End Spacer
as shown in Fig. 7 using the screws supplied and
fully tighten.
10. Connect the free end of the linking kit supply cord
either directly to a îš¿xed wiring outlet or to a suitable
13 amp plug with a 3 amp fuse îš¿tted.
Cable Replacement
IMPORTANT: In the event of supply cable replacement
only an approved PVC cable capable of withstanding
a continuous minimum operating temperature of
85 degrees should be used. Rubber insulated and
sheathed cable should not be used.
If the supply cord is damaged it must be replaced by the
manufacturer or service agent or a similarly qualiîš¿ed
person in order to avoid a hazard.
[c] GDC Group Ltd
All rights reserved. Material contained in this publication may not be reproduced in whole or in part, without prior permission in writing of GDC Group Limited.

Product specificaties

Merk: Dimplex
Categorie: Heater
Model: ECOT5FT

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex ECOT5FT stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Heater Dimplex

Dimplex

Dimplex DTD4T Handleiding

15 November 2024
Dimplex

Dimplex DX 425E Handleiding

15 November 2024
Dimplex

Dimplex Mini Cube Handleiding

15 November 2024
Dimplex

Dimplex Huxley Revillusion HXY20-AU Handleiding

25 Maart 2024
Dimplex

Dimplex Strata Revillusion STA20-AU Handleiding

25 Maart 2024
Dimplex

Dimplex Sherwood Revillusion SWD20-AU Handleiding

25 Maart 2024
Dimplex

Dimplex SILVERTON Handleiding

26 Februari 2024
Dimplex

Dimplex MOCCA Handleiding

26 Februari 2024
Dimplex

Dimplex DHEBHT Handleiding

26 Februari 2024
Dimplex

Dimplex BK 1202 S Handleiding

26 Augustus 2023

Handleiding Heater

Nieuwste handleidingen voor Heater

Trisa

Trisa 9330.44 Handleiding

18 December 2024
Hortus

Hortus 211-413 Handleiding

18 December 2024
Yamazen

Yamazen HF-L122 Handleiding

18 December 2024
Yamazen

Yamazen HF-D121 Handleiding

18 December 2024
Yamazen

Yamazen HF-L121 Handleiding

18 December 2024
Universal Blue

Universal Blue UCRA9104-24 Handleiding

18 December 2024
Orava

Orava VL-203 Handleiding

18 December 2024
SHX

SHX HL20OSZ Handleiding

16 December 2024
Stanley

Stanley ST-125T-KFA-ES Handleiding

16 December 2024
Perel

Perel PHS2000 Handleiding

14 December 2024