Dimplex DXFF30TSN Handleiding

Dimplex Heater DXFF30TSN

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex DXFF30TSN (4 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

DO NOT COVER

DXFF20TSN & DXFF30TSN

08/51250/0 Issue 6

The product complies with the European Safety Standards EN60335:2-30 and the European Standard Electromagnetic Compatibility (EMC) EN55014:1,

EN55014:2, EN61000:3-2 and EN61000:3-3 which cover the essential requirements of EMC Directive 2014/30/EU and the LVD Directive 2014/35/EU.

As with all portable heang appliances: This product is suitable only for well insulated spaces or occasional use.

Installation and Operating Instructions

Important Safety Advice

DO NOT use the heater in the immediate

surroundings of a bath, a shower or a swimming

pool.

DO NOT place the heater directly below a xed

socket outlet.

The socket-outlet must be accessible at all times

to enable the mains plug to be disconnected as

quickly as possible.

DO NOT COVER or obstruct the air inlet and

outlet openings in any way.

The heater must be on a at stable surface when

in use.

DO NOT operate the heater with the mains lead

overhanging the front outlet grille.

The Heater carries the warning symbol

indicating that it must not be covered.

WARNING: In order to avoid overheating do not

cover the heater.

IMPORTANT: If the mains lead of this appliance is

damaged, it must be replaced by the manufacturer

or its service agent or a similarly qualied person

in order to avoid a hazard.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged from

8 years and above and persons with reduced

physical, sensory or mental capabilities or lack of

experience or knowledge if they have been given

supervision or instruction concerning the use of

the appliance in a safe way and understand the

hazards involved. Children shall not play with the

appliance. Cleaning and user maintenance shall

not be made by children without supervision.

Children of less than 3 years should be kept away

unless continuously supervised.

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

Children aged from 3 years and less than 8 years

shall only switch on/off the appliance provided

that it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning the

use of the appliance in a safe way and understand

the hazards involved. Children aged from 3

years and less than 8 years shall not plug in,

regulate and clean the appliance or perform user

maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present.

IMPORTANT: Avoid use of an extension cord

because the extension cord may overheat and

cause risk of re.

DO NOT use the heater on deep pile carpets or

the long hair type of rugs, or less than 750mm

(30”) away from any overhanging surface. Keep

combustible materials such as drapes and other

furnishings away from the sides and rear and at

least 750mm away from the front of the heater.

DO NOT use heater to dry your laundry.

The instruction leaet belongs to the appliance

and must be kept in a safe place. If changing

owners, the leaet must be surrendered to the

new owner.

IMPORTANT: Normal use of your fan heater in

areas which have high levels of uff, dust or hair

(e.g. bedrooms, dressing areas or hair salons),

especially on solid/lino covered oors, will result

in the accumulation of these inside the heater at

the back of the element. If left to build up it will

eventually result in the safety cut-out operating

to protect you and the heater from the danger

of the product overheating. It is therefore critical

that you use a vacuum cleaner to regularly blow

out and clean away any accumulation from the

heater. (See Cleaning section overleaf for more

detailed instructions on how to do this)

Model s( )  Specication

DXFF20TSN 2.0kw Switch, Thermostat & Neon

DXFF30TSN 3.0kw Switch, Thermostat & Neon

DXFF20TSN & DXFF30TSN Flat Fan Heaters

IMPORTANT: DO NOT USE AS A HAIRDRYER

REGULAR VACUUM CLEANING IS REQUIRED

TO ENSURE PROPER OPERATION (see below)

See ‘Fig. 3’

See ‘Fig. 2’

Mains Neon

Air Outlet

Handle

Air Inlet

Fig. 1

DO NOT COVER

* When the heat control is set to ‘ ’ for Cool Blow, set the

thermostat control to max. position.

Position ‘ will turn the heater on and off to maintain a ’

temperature of approximately 5°C to help protect against frosty

conditions.

Safety - Overheat Cut-out

For your safety, this appliance is tted with a thermal cut-out. In the

event that the product overheats, the cut-out switches the heater

off automatically. To bring the heater back into operation, remove

the cause of the overheating, then unplug or turn off the electrical

supply to the heater for a few minutes. When the heater has cooled

sufciently, re-connect and switch on the heater.

Fuselink

A thermal fuse link is provided as an added safety feature. If the

fuse link operates and opens circuit it is the result of abnormal

overheating within the appliance and servicing of the appliance by

a competent service engineer will be required in order to ensure

the future safe operation of the heater. Customer services should

be contacted, who will arrange the replacement of any faulty parts

and the tting of a new fuse link.

Cleaning

WARNING: Always disconnect from the power supply before

cleaning the heater.

To ensure continued normal operation of your heater, you must

regularly clean out any accumulation of particles from inside the

heater.

This is best achieved by using your vacuum cleaner in blow mode

to blow air into the heater through the front air outlet to dislodge

any accumulated matter from the back of the element (If it does

not have this function then blowing hard yourself will have the

same result). Then use the vacuum in suction mode to suck out

the now loose particles through the top and bottom air inlets. This

will serve to clean these areas also.

For normal surface cleaning, do not use detergents, abrasive

cleaning agents or polish of any kind on the heater. Wipe with a

dry cloth to remove dust and a damp (not wet) cloth to clean off

stains. Be careful not to allow moisture into the heater.

Recycling

For electrical products sold within the European

Community.

At the end of the electrical products useful life it

should not be disposed of with household waste.

Please recycle where facilities exist. Check with

your Local Authority or retailer for recycling advice

in your country.

ModelIdentier(s): DXFF20TSN DXFF30TSN

Heat output

Nominal heat output Pnom 2.0 3.0 kW

Minimum heat output (indicative) Pmin 1.0 1.5 kW

Maximum continuous heat output Pmax,c 2.0 3.0 kW

Auxiliary electricity Consumption

At nominal heat output 0.0 0.0elmax kW

At minimum heat output elmin 0.0 0.0 kW

In standby mode elSB 0.0 0.0 kW

Type of heat output/ room temperature control

Mechanical thermostat room temperature control Yes

Contact details

GDHV Group Limited

Millbrook House, Grange Drive,

Hedge End, Southampton.

SO30 2DF

Electrical connection

This heater must be used on an ~ supply only and the voltage

marked on the heater must correspond to the supply voltage. This

heater is tted with a rewirable plug incorporating a 13 amp fuse.

In the event of replacing the fuse in the plug supplied, a 13 amp

fuse approved by ASTA to BS 1362 must be used. If any other

type of plug is used, a 15 amp fuse must be tted in the plug, the

adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp

plug should be removed. Before wiring the appropriate plug, please

note that the wires in this mains lead are coloured in accordance

with the following code :

BLUE : NEUTRAL

BROWN : LIVE

As the colours of the wires in the mains lead may not correspond

with the coloured markings in your plug, proceed as follows :

Connect the wire to the terminal marked ‘ ’ or coloured BROWN L

RED BLUE. Connect the wire to the terminal marked ‘N’ or

coloured .BLACK Note : ‘L’ or ‘N’ wire must not be connected

to the EARTH terminal marked ‘E’ or ‘ ’ or coloured GREEN

or . If in doubt, consult your electrician.GREEN AND YELLOW

Using the heater

The mains neon (see ) will light up to show that the heater Fig. 1

is connected to the mains supply.

Heat control Fig. 2 - see

The heat control positions are as follows:

O - Off

- Cool Blow *

I Half heat output-

II - Full heat output

Fig. 2

Thermostat control Fig. 3- see

The heat output is controlled by the thermostat, according to the

room temperature. Turn the knob to maximum setting initially.

When the room is warm enough, reduce the setting slowly until

the heater just clicks off.

The heater will now cycle on and off to maintain your selected

room temperature.

Fig. 3

NOTE: If the heater does not come on when the thermostat is

set low, this is normally because the room is warmer than the

thermostat setting and is not a fault.

Product specificaties

Merk:	Dimplex
Categorie:	Heater
Model:	DXFF30TSN
Soort bediening:	Draaiknop
Kleur van het product:	Wit
Gewicht:	1200 g
Breedte:	253 mm
Diepte:	245 mm
Hoogte:	114 mm
Soort:	Ventilator elektrisch verwarmingstoestel
Instelbare thermostaat:	Ja
Oververhittingsbeveiliging:	Ja
Draagbaar:	Ja
Bevriezings beveiliging:	Ja
Verwarmingsvermogen:	3000 W
Plaatsingsopties:	Tafel
Verwarming power (min):	- W
Zomer-ventilatie:	Ja