Dimplex DXC20TI Handleiding

Dimplex Heater DXC20TI

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex DXC20TI (7 pagina's) in de categorie Heater. Deze handleiding was nuttig voor 11 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/7

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

As with all portable heating appliances - This product is only suitable for well insulated spaces or occasional use

Dimensions (millimetres)

Installation and Operating Instructions

Convector Heaters

Models : DXC20, DXC20Ti, DXC20F, DXC20FTi, DXC30, DXC30Ti, DXC30F and DXC30FTi INDCUK35RG Issue 5

Models Specication

DXC20 2.0kW On/Off Switch/Heat Switch/T’stat/Neon

DXC20Ti 2.0kW Heat Switch/T’stat/24hr Timer

DXC20F 2.0kW On/Off Switch/Heat Switch/T’stat/Neon/Turbo Fan

DXC20FTi 2.0kW Heat Switch/T’stat/Neon/24hr Timer/Turbo Fan

DXC30 3.0kW On/Off Switch/Heat Switch/T’stat/Neon

DXC30Ti 3.0kW Heat Switch/T’stat/24hr Timer

DXC30F 3.0kW On/Off Switch/Heat Switch/T’stat/Neon/Turbo Fan

DXC30FTi 3.0kW Heat Switch/T’stat/Neon/24hr Timer/Turbo Fan

150

418

230 695 - 3.0kW

575 - 2.0kW

MIN

Important Safety Advice

WARNING: This appliance must not be used in

a bathroom.

WARNING: Do not use this heater in the

immediate surroundings of a bath, a shower or

a swimming pool.

WARNING: This heater must not be located

immediately below a xed socket outlet.

The heater carries a warning symbol to

alert the user to the risk of re that exists

if the heater is accidentally covered.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience or knowledge if they have

been given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided that

it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform

user maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present. If the mains

lead is damaged, it must be replaced by the

manufacturer or its service agent or a similarly

qualied person in order to avoid a hazard.

WARNING: Do not use the heater on deep

pile carpets or the long hair type of rugs. Keep

combustible materials such as drapes and other

furnishings clear from the front, sides and rear

of the heater. Do not use the heater to dry your

laundry.

The instruction leaet belongs to the appliance

and must be kept in a safe place. If changing

owners, the leaet must be surrendered to the

new owner.

WARNING: Do not use heater in small rooms

when they are occupied by persons who are not

capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: The heater should only be used

on a horizontal and stable surface with the feet

securely tted.

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is not advised when

connecting this product to the mains. Connection through these devices

could lead to a risk of overloading, overheating and even re at the extension

lead or adaptor due to inadequate connection quality.

This heater must be used on an AC (~) supply only and the voltage marked

on the heater must correspond to the supply voltage. This heater is tted

with a rewireable plug incorporating a 13 amp fuse. In the event of replacing

the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse must be

tted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code : GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the wire to the terminal marked ‘ ’ or GREEN AND YELLOW E

by the earth symbol , or coloured or .GREEN GREEN AND YELLOW

Connect the wire to the terminal marked ‘ ’ or coloured .BROWN L RED

Connect the wire to the terminal marked ‘ ’ or coloured BLUE N BLACK.

Fig. 1

Using the heater

Plug in and switch on at the wall socket. The mains neon indicator will glow

showing that power is available.

On models with a timer clock, the clock will operate all the time that the

heater is connected to the mains supply, regardless of the setting of the heat

selector switch. Set the timer control switch as required for OFF, Manual

or Automatic operation – see .‘Timer Operations’

The heat output is controlled by the

thermostat - see .‘Thermostat’

Controls

Thermostat

The thermostat controls the heat output

according to the room temperature.

This ensures that the heater will not

produce heat unnecessarily when the

room is warm.

To set the temperature you require,

turn the thermostat knob clockwise until

the desired temperature is reached.

Alternatively to heat a cold room

quickly, turn the thermostat knob up

fully.

When the room has reached the desired

temperature, turn the thermostat knob

anti-clockwise until the thermostat just

clicks off.

The heater will now automatically

operate at this temperature.

The thermostat also has a frost

protection setting marked ‘ ’. This

setting is useful in areas such as

garages to prevent frost damage. If

the thermostat is set to its minimum

setting ‘ ’, the heater will cycle ON

and OFF to maintain a temperature

of approximately 5°C to help protect

against frosty conditions.

On/Off Switch - see Fig. 4a

On the non-timer models the switch

operates as follows:

O - The heater is Off

I - The heater operates with heat output as per the heat selection switch.

Note : The above description of the On/Off switch operation is with the turbo

neon switch in the off position – see also the ‘Turbo Fan model...’ section.

Free standing use

NEVER USE THE HEATER FREE STANDING WITHOUT THE FEET

FITTED.

Lay the heater on its back, locate the foot xing screw (see ‘a’ in Fig. 2) and

remove the screw using an X–head screwdriver, then align foot over slots

and holes in base (see ‘b’ in ) and push into the slots. Finally take the Fig. 2

foot xing screw, insert and tighten using a screwdriver to secure the foot.

Thermostat

Knob

Heat Selector

Switch

Timer

Fig. 4b

Timer Models

Fig. 4a

Non- Timer Models

Thermostat

Knob

Neon

On/Off Switch

Heat Selector

Switch

Using the heater

WARNING: DO NOT USE THE HEATER UNTIL THE FEET ARE

FITTED CORRECTLY.

The product can only be used as a portable unit. Once the requirements

below have been met the product is ready to be used. Simply plug in and

switch on at the wall socket.

There are various control options available with various combinations

comprising of thermostat, switched, timer & indicating neons. Please note

– the element has been coated with a protective lm which will burn off

during the rst few minutes of use and may cause a small amount of fuming.

This is quite normal – the fumes are non-toxic and will quickly disappear.

We recommend that you open a window to ventilate the room when using

the heater for the rst time.

Positioning the heater

Always ensure that the heater is stood on a rm, level base near to, but

not directly beneath, a suitable mains supply socket.

Ensure that curtains and furniture are not positioned close to the chosen

position, as this would create a potential re hazard. If young children, the

aged or inrm are likely to be left in the vicinity of the heater, we advise

that adequate precautions should be taken. We recommend that a guard

be tted to ensure contact with the heater is avoided and objects cannot

be inserted into the product.

For further information, please contact our guard supplier direct on Tel.

No. 0207 987 1184, or in case of difculty or for further advice contact the

Customer Helpline.

(a) (b)

Fig. 2

Foot

Fixing

Screw

Heat Selector Switch - see and Fig. 4a Fig. 4b

Heat selection is available on all models as an economy feature.

On all models the switch operates as follows:

I - The heater operates with low heat output

II - The heater operates with max. heat output

Mechanical Timer Operation - see Fig. 5

Set the - I - slide switch on the timer ( ) to:Fig. 6

Position - Heating Off

Position I - Manual operation

T h i s s et ti n g al l o w s p o w e r t o t h e

heater uninterrupted by the timer settings.

The heat selector switch and thermostat

will control the output (see ‘Controls’).

Position - ‘Auto’ operation

DO NOT disconnect this heater from the

mains supply unless it is being taken out

of use (e.g. in summer or for storage),

otherwise the timer clock will stop.

Setting the time of day

To set the time of day, rotate the timer dial clockwise (indicated by the arrow)

until the correct time of day is opposite the reference mark (see Fig.

6). The 24-hour clock is used ; e.g. time shown for 4 pm is ‘16’ (16:00hrs).

Setting the ‘Auto’ ON and OFF times

To set the timer:

1. Using your nger tip or the tip of a pencil,

push in as many segments as necessary

around the dial, according to the times

you don’t require heat – see . Each Fig. 7

segment pushed in switches the heater OFF

for that part of the hour. All other segments

will be ON. For example, Fig. 8 shows the

timer set to switch the heater ON between

9.00am and 4.00pm and between 9.30pm

and 7.00am.

2. You can select as many ON periods as you like, within the 24-hour day.

The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments you

wish to cancel and pull out new ‘ON’ segments as required.

Switching to auto

Set the heat selector and thermostat for

the heat output required.

Check that the clock shows the correct

time of day. Set the - - I slide switch

to (see ) - the heater will switch Fig. 9

ON and OFF according to the timer

settings (see ).Fig. 8

IMPORTANT NOTES

Remember to observe all safety warnings when operating the heater on

auto setting unattended or attended.

If the mains supply to the heater is interrupted, the timer clock will stop until

power is restored ; reset the time of day to ensure correct ON and OFF times.

Turbo Fan models - see Fig. 10

The turbo fan can be used to circulate

the heat around the room to help it

reach the desired temperature more

quickly.

DXC20F & DXC20FTi

To circulate the heat around the room

to reach the desired temperature

quickly, set the heat selector switch

to either the low or high setting and

the turbo switch on. In warm weather

the fan can be used to circulate cool

air. Set the two switches to OFF and

the turbo switch to ON, then turn the

thermostat knob fully clockwise to the

maximun setting.

DXC30F & DXC30FTi

On this model with the switch at position and the turbo switch in it’s I / II I

Off position ( neon off ) there is no heat output from the convector. With

the /I II switch still in the I position you can have 1kw output but only with

the turbo boost On (neon on). To get an output of 2kW leave the turbo

switch off and set the switch to position . (Note 2kw is only possible I / II II

with turbo Off). To achieve 3kw output now turn on the turbo switch which

will combine the 2kW setting with a 1kW fan boost setting to give the total

output of 3kw with fan boost.

Note that the fan and the neon on the Turbo switch will cycle on and off

under the control of the thermostat – see ‘Thermostat’.

Safety – overheat protection

For your safety, this appliance is tted with a thermal cut-out. In the event

that the product overheats, the cut-out switches the heater off automatically.

To bring the heater back into operation, remove the cause of the overheating,

then unplug or turn off the electrical supply to the heater for a few minutes.

When the heater has cooled sufciently, re-connect and switch on the

heater.

Important Notes

Although this heater is manufactured to comply with the relevant safety

standards, certain types of carpets could become discoloured by the

temperatures under a portable heater. If you are concerned about this,

we recommend that you contact the carpet manufacturer for guidance.

Alternatively, either stand the heater on a suitable base to shield the carpet

or call our Helpline for further advice.

You may notice some parts of the element appearing to be hotter from time

to time because of the variable airow through the heater. This does not

cause a safety hazard.

The heat outlet grille may become discoloured with use – this is caused by

airborne pollution and is not a fault.

Fig. 6

Fig. 7

Fig. 9

Turbo

ON/OFF

Neon

Switch

Fig. 10

Fig. 5

Fig. 8

Product specificaties

Merk:	Dimplex
Categorie:	Heater
Model:	DXC20TI
Soort bediening:	Draaiknop
Kleur van het product:	Wit
Timer:	Ja
Gewicht:	3400 g
Breedte:	575 mm
Diepte:	196 mm
Hoogte:	418 mm
Soort:	Radiator
Instelbare thermostaat:	Ja
Verwarmingsvermogen:	2000 W
Plaatsingsopties:	Wall, Floor
Verwarming power (min):	- W