Dimplex 403TSF Handleiding

Dimplex Niet gecategoriseerd 403TSF

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex 403TSF (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 193 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

attention has to be given where children and

vulnerable people are present.

WARNING: Do not use the heater in small rooms

when they are occupied by persons who are not

capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: To reduce the risk of re, keep

textiles, curtains or any other ammable material

a minimum distance of 1m from the air outlet.

Do not use the heater if it has been dropped.

Do not use the heater if there are any visible

signs of damage.

If the mains lead is damaged, it must be replaced

by the manufacturer or its service agent or a

similarly qualied person in order to avoid a

hazard.

The heater should only be used on a horizontal

and stable surface with the feet securely tted

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is not advised when

connecting this product to the mains. Connection through these devices

could lead to a risk of overloading, overheating and even re at the extension

lead or adaptor due to inadequate connection quality.

This heater must be used on an ~ supply only and the voltage marked on

the heater must correspond to the supply voltage. This heater is tted with

a rewireable plug incorporating a 13 amp fuse. In the event of replacing

the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse must be

tted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code : GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the wire to the terminal marked ‘ ’ or GREEN AND YELLOW E

by the earth symbol , or coloured or .GREEN GREEN AND YELLOW

Connect the wire to the terminal marked ‘ ’ or coloured .BROWN L RED

Connect the wire to the terminal marked ‘ ’ or coloured BLUE N BLACK.

Important Safety Advice

WARNING: This appliance must not be used in

a bathroom.

WARNING: Do not use this heater in the

immediate surroundings of a bath, a shower or

a swimming pool.

WARNING: This heater must not be located

immediately below a xed socket outlet.

The heater carries a warning symbol to

alert the user to the risk of re that exists

if the heater is accidentally covered.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience or knowledge if they have

been given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided that

it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform

user maintenance.

Dimensions

(Millimetres)

Installation and Operating Instructions

Dimplex Convector Heaters

Models : 403TS, 403TSF, 403TSTi & 403TSFTie

INDCUK40RG Issue 5

Models Specication

403TS 3.0kw Thermostat & 2 heat settings & Neon.

403TSF 3.0kw Thermostat, 2 heat settings, Turbo & Neon.

403TSTi 3.0kw Thermostat, 2 heat settings, Timer & Neon.

403TSFTie 3.0kw Thermostat, 2 heat settings, Timer & Turbo.

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

As with all portable heating appliances - This product is only suitable for well insulated spaces or occasional use

Fig. 1

Using the heater

WARNING: DO NOT USE THE HEATER UNTIL THE FEET ARE

FITTED CORRECTLY.

The product is intended for occasional use as a portable unit. Please ensure

the feet are securely tted before the product is used. Once the feet have

been installed simply plug in and switch on at the wall socket.

There are various control options available with various combinations

comprising of thermostat, switched, timer & indicating neons.

Please note – the element has been coated with a protective lm which

will burn off during the rst few minutes of use and may cause a small

amount of fuming. This is quite normal – the fumes are non-toxic and will

quickly disappear.

We recommend that you open a window to ventilate the room when using

the heater for the rst time.

Positioning the heater

Always ensure that the heater is stood on a rm, level base near to, but

not directly beneath, a suitable mains supply socket.

Ensure that curtains and furniture are not positioned close to the chosen

position, as this would create a potential re hazard.

Product Assembly

WARNING: THE HEATER SHOULD NEVER BE USED WITHOUT THE

FEET SECURELY FITTED.

WARNING: ONLY THE SCREWS SUPPLIED WITH THIS PRODUCT

SHOULD BE USED TO MOUNT THE FOOT. A MAXIMUM SCREW

LENGTH OF 10MM SHOULD BE USED.

Lay the heater on its back so the underneath of the product is accessible.

Locate and remove the foot xing screw - see Fig. 2(a). Clip the foot in

place and secure using the foot xing screw - see Fig. 2(b).

Controls

Model 403TSTi Model 403TSF

Heat selector

switch

Thermostat

knob

Neon

Mechanical

Timer

Control

switch

Thermostat

knob

Neon

Thermostat (all models)

The thermostat controls the heat output according to the room temperature.

This ensures that the heater will not produce heat unnecessarily when the

room is warm.

To set the temperature you require, gradually turn the thermostat knob

clockwise until the desired temperature is reached. Allow some time

between increments for the room temperature to stabilise.

Alternatively to heat a cold room quickly, turn the thermostat knob to the

Max position. When the room has reached the desired temperature, turn

the thermostat knob anti-clockwise until the thermostat clicks off. The heater

will then automatically maintain this room temperature.

The thermostat also has a frost protection setting marked ‘ ’. This setting is

useful in areas such as garages to prevent frost damage. If the thermostat is

set to its minimum setting ‘ ’, the heater will cycle ON and OFF to maintain

a temperature of approximately 5°C to help protect against frosty conditions.

Fig. 2

Fig. 3

Switches (selected models)

Some models are supplied with selector switches . There are two switch

types, one is an on/off switch and the other is a heat selection switch.

Depending on model either one or both switch may be included. The switch

operation is as follows.

On/ Off: O - Off

I - On

Heat selection - Low heatI

II - High heat

403TS Operation

This model contains an On/Off switch and a heat selection switch and

operates as follows.

When O/I O switch is in position the product is off regardless of any other

setting. When switch is in position and the O/I I I/II switch is in the I position

there is a low heat output from the product. When switch is in position O/I

I I/II II and the switch is in the position there is a high heat output from the

product. The indicator neon is always on when the product is connected

to the mains supply.

403TSTi Operation

This model contains a heat selection switch and an electro-mechanical

timer and operates as follows.

When the timer is switched to and the switch is in position there is I I/II I

a low heat output from the product. When the timer is switched to and I

the I/II switch is in position II there is a high heat output from the product.

When the timer is in the ‘ ’ position and the switch is in position there I/II I

is a low heat output from the product when the timer is set on. When the

timer is in the ‘ ’ position and the switch is in position there is a high I/II II

heat output from the product when the timer is set on. The indicator neon

is always on when the product is connected to the mains supply.

Mechanical Timer (403TSTi)

Note: The timer clock will only operate when the product is connected to

the mains supply

Operation modes

There are two operating modes on the timer, Manual operation and Auto

operation. The operation mode is set using the slide switch on the timer

- see g4.

Manual operation (Position - I)

This setting allows power to the product uninterrupted by the timer,

however other product controls will continue to function as normal.

Auto operation (Position - )

This setting allows the heater to be controlled by the timer. The product

will be switched on and off depending on the pre-set timer program.

Setting the time of day

To set the time of day, rotate the timer dial clockwise (indicated by the

arrow) until the correct time of day is opposite the reference mark -

see . The 24-hour clock is used ; e.g. 4 pm is ‘16’ (16:00hrs)Fig. 4 .

Setting the ‘Auto’ ON and OFF times

To set the timer :

1. Using your nger tip or the tip of a pencil, push in as many

segments as necessary around the dial, according to the times you

don’t require heat – see . Each segment pushed in switches Fig. 5

the heater OFF for that part of the hour. All other segments will be

ON. For example, shows the timer set to switch the heater Fig. 5

OFF between 11pm and 1.45am.

2. You can select as many ON periods as you like, within the 24-hour

day. The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Fig. 4

Initial Operation

For initial use, plug the heater into a regular household power point and

turn the power on. The timer is now ready to be set up for use.

13 17:

OFF

ADVANCE

AUTO

MANUAL ON

Setting Current Time

1. Hold the ‘ ’ button until the clock symbol appears on the PROGRAM

top left hand side of the screen. The user can now set the clock.

2. The hour digit will ash. To adjust the hour use the ‘- +‘ & ‘ ’ buttons.

Conrm the hour digit by pressing ‘ENTER’.

3. Once ‘ENTER’ has been pressed the minutes will ash. To adjust

the minutes use the ‘-‘&‘+’ buttons. Conrm the minute digit by pressing

‘ENTER’.

4. The timer now returns to the default display.

5. To reset incorrect time, repeat previous steps.

Once the correct time is set, a total of four ON/OFF time programs can be

set for operation. There are two program options.

Setting Programmes

Press the ‘ ’ key to set the programs. PROGRAM

You are now setting the programs starting with P1 ‘ON’.

SETTING P1 ON TIME:

1. To set the hour use the ‘ ‘ & ‘- +’ buttons. Conrm the hour digit by pressing

‘ ’. ENTER

2. To set the minutes use the ‘ ‘ & ‘- +’ buttons. Conrm the minute digit by

pressing ‘ ’.ENTER

Note: The minutes can only be set in 10 minute blocks in programme

‘ ’. MODE

SETTING P1 OFF TIME:

3. To set the hour use the ‘ ‘ & ‘- +’ buttons. Conrm the hour digit by pressing

‘ ’. ENTER

4. To set the minutes use the ‘ ‘ & ‘- +’ buttons. Conrm the minute digit by

pressing ‘ ’.ENTER

Repeat steps 1 to 4 to programme P2, P3 & P4. After programming P4

‘OFF’ you automatically exit to the default display.

At any time while programming the timer you can press the ‘PROGRAM’

button to exit to the default display.

The Advance Function

When in ‘ ’ MODE, if the ‘ ’ button is pressed for longer than 2 AUTO +

seconds the programme will ADVANCE to the next setting programmed

and will only revert back to the program when the subsequent programme

time is reached. When the ‘ADVANCE’ function is running the ‘ADVANCE’

segment will be displayed on the LCD screen. If the ‘ ‘ button is pressed -

when the ‘ADVANCE’ programme is running the ‘ADVANCE’ feature will

be automatically cancelled and the programme will run as normal.

Note - Timer Memory Back Up Batteries - Once the heater has been

left plugged in with the socket switched on for at least 72 hours the timer’s

memory back up batteries will be fully charged.

Once the timer batteries are fully charged, if there is a power cut or if the

heater is disconnected from the mains for less than six months, then the

timer will continue to keep time & the settings in the memory will remain

intact.

Safety – overheat protection

For your safety, this appliance is tted with a thermal cut-out. In the event

that the product overheats, the cut-out switches the heater off automatically.

To bring the heater back into operation, remove the cause of the overheating,

then unplug or turn off the electrical supply to the heater for a few minutes.

When the heater has cooled sufciently, re-connect and switch on the

heater.

Fig. 7

Switching to auto

Ensure the thermostat and/or the heat selector are set for the desired

heat output.

Check that the clock shows the correct time of day. Set the mode slide

switch to , the heater will switch ON and OFF according to the timer

settings (see ).Fig. 5

Important notes

Remember to observe all safety warnings when operating the heater on

auto setting unattended or attended .

If the mains supply to the heater is interrupted, the timer clock will stop until

power is restored ; reset the time of day to ensure correct ON and OFF times.

403TSF Operation

This model contains an On/Off switch and operates as follows.

When O/I switch is in position O the product is off regardless of any other

setting. When switch is in position and the turbo switch is there is O/I I Off

a low heat output from the product. The turbo fan will be off.

When O/I I On switch is in position and the turbo switch is the heater goes

into high heat fan boost mode. There is a high heat output from the product.

The turbo fan will be running. The indicator neon is always on when the

product is connected to the mains supply.

Note: there is no cold blow operation on this model and all heat settings

and the turbo fan operate under the control of the thermostat

Turbo fan (Boost mode)

The turbo fan is used to boost

the airow around the room. This

circulates the heat better and

results in a reduced heat up time

and a more even heat distribution.

The turbo fan is controlled by the

neon switch on the front of the

product.

403TSFTie Operation

This model contains an On/Off switch and operates as follows.

When O/I switch is in position O the product is off regardless of any other

setting. The timer will continue to operate but cannot turn on the product

When O/I switch is in position I and the turbo switch is Off there is a low

heat output from the product. The turbo fan will be off.

When O/I I On switch is in position and the turbo switch is the heater goes

into high heat fan boost mode. There is a high heat output from the product.

The turbo fan will be running. The neon indicator on the timer will only be

on when the timer is on an ‘On’ cycle.

Note: there is no cold blow operation on this model and all heat settings

and the turbo fan operate under the control of the thermostat

Digital Timer (403TSFTie) - see Fig. 7

IMPORTANT: Remember to observe all safety warnings when operating

the heater on auto setting, either attended or unattended.

The timer allows you to select ‘AUTO’ or ‘ ’ by pressing the ‘MODE’ MAN ON

button until the required MODE appears at the bottom of the timer display.

‘AUTO’ MODE allows the heater to switch ON and OFF according to a set

24 Hour program period (see ‘Setting Programs’ section below).

‘MAN ON’ MODE allows power to the heater uninterrupted by the program

settings.

Key Lock:

If ‘ ’ and ‘ ’ are pressed within 1 second, the keys will be ENTER MODE

locked. The user will know the keys are locked as the lock symbol ‘ ’ will

be displayed on the top left hand corner of the screen. To unlock the keypad,

press ‘ ’ and then ‘ ’ within 1 second.ENTER MODE

Fig. 6

Fig. 5

Product specificaties

Merk:	Dimplex
Categorie:	Niet gecategoriseerd
Model:	403TSF
Kleur van het product:	Wit
Aantal vermogenniveau's:	2
Gewicht:	4500 g
Breedte:	733 mm
Diepte:	200 mm
Hoogte:	442 mm
Snoerlengte:	1.2 m
Gewicht verpakking:	5000 g
Breedte verpakking:	819 mm
Diepte verpakking:	130 mm
Hoogte verpakking:	393 mm
Soort:	Convector elektrisch verwarmingstoestel
Geschikt voor:	Binnen
Instelbare thermostaat:	Ja
Commodity Classification Automated Tracking System (CCATS):	8516295000
Verwarmingsvermogen:	3000 W
Plaatsingsopties:	Floor, Wall
Verwarmingselement type:	Aluminium
Verwarming power (min):	1950 W