Dimplex 402TSF Handleiding

Dimplex Niet gecategoriseerd 402TSF

Lees hieronder de 📖 handleiding in het Nederlandse voor Dimplex 402TSF (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

attention has to be given where children and

vulnerable people are present.

WARNING: Do not use the heater in small rooms

when they are occupied by persons who are not

capable of leaving the room on their own, unless

constant supervision is provided.

WARNING: To reduce the risk of re, keep

textiles, curtains or any other ammable material

a minimum distance of 1m from the air outlet.

Do not use the heater if it has been dropped.

Do not use the heater if there are any visible

signs of damage.

If the mains lead is damaged, it must be replaced

by the manufacturer or its service agent or a

similarly qualied person in order to avoid a

hazard.

The heater should only be used on a horizontal

and stable surface with the feet securely tted

Electrical connection

WARNING – THIS APPLIANCE MUST BE EARTHED

The use of an extension lead or multi-plug adaptor is not advised when

connecting this product to the mains. Connection through these devices

could lead to a risk of overloading, overheating and even re at the extension

lead or adaptor due to inadequate connection quality.

This heater must be used on an ~ supply only and the voltage marked on

the heater must correspond to the supply voltage. This heater is tted with

a rewireable plug incorporating a 13 amp fuse. In the event of replacing

the fuse in the plug supplied, a 13 amp fuse approved by ASTA to BS 1362

must be used. If any other type of plug is used, a 15 amp fuse must be

tted in the plug, the adaptor, or at the distribution board.

IMPORTANT : If the plug is not suitable for your socket, the 13 amp plug

should be removed. Before wiring the appropriate plug, please note that

the wires in this mains lead are coloured in accordance with the following

code : GREEN AND YELLOW: EARTH

BLUE : NEUTRAL

BROWN : LIVE

Connect the wire to the terminal marked ‘ ’ or GREEN AND YELLOW E

by the earth symbol , or coloured or .GREEN GREEN AND YELLOW

Connect the wire to the terminal marked ‘ ’ or coloured .BROWN L RED

Connect the wire to the terminal marked ‘ ’ or coloured BLUE N BLACK.

Important Safety Advice

WARNING: This appliance must not be used in

a bathroom.

WARNING: Do not use this heater in the

immediate surroundings of a bath, a shower or

a swimming pool.

WARNING: This heater must not be located

immediately below a xed socket outlet.

The heater carries a warning symbol to

alert the user to the risk of re that exists

if the heater is accidentally covered.

WARNING: In order to avoid a hazard due to

inadvertent resetting of the thermal cut-out,

this appliance must not be supplied through an

external switching device, such as a timer, or

connected to a circuit that is regularly switched

on and off by the utility.

This appliance can be used by children aged

from 8 years and above and persons with

reduced physical, sensory or mental capabilities

or lack of experience or knowledge if they have

been given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children shall

not play with the appliance. Cleaning and user

maintenance shall not be made by children

without supervision.

Children of less than 3 years should be kept

away unless continuously supervised. Children

aged from 3 years and less than 8 years shall

only switch on/off the appliance provided that

it has been placed or installed in its intended

normal operating position and they have been

given supervision or instruction concerning

the use of the appliance in a safe way and

understand the hazards involved. Children aged

from 3 years and less than 8 years shall not plug

in, regulate and clean the appliance or perform

user maintenance.

CAUTION: Some parts of this product can

become very hot and cause burns. Particular

Dimensions

(Millimetres)

Installation and Operating Instructions

Dimplex Convector Heaters

Models : 402T, 402TS, 402TSTi, 402TSF & 402TSFTi

08/52558/0 Issue 3

Models Specication

402T 2.0kw Thermostat,

402TS 2.0kw Thermostat & 2 heat settings,

402TSTi 2.0kw Thermostat, Timer & Neon,

402TSF 2.0kw Thermostat & 2 heat settings, Turbo & Neon,

402TSFTi 2.0kw Thermostat, 2 heat settings, Timer, Turbo & Neon

IMPORTANT : THESE INSTRUCTIONS SHOULD BE READ CAREFULLY AND RETAINED FOR FUTURE REFERENCE

As with all portable heating appliances - This product is only suitable for well insulated spaces or occasional use

Fig. 1

Using the heater

WARNING: DO NOT USE THE HEATER UNTIL THE FEET ARE

FITTED CORRECTLY.

The product is intended for occasional use as a portable unit. Please ensure

the feet are securely tted before the product is used. Once the feet have

been installed simply plug in and switch on at the wall socket.

Please note – the element has been coated with a protective lm which

will burn off during the rst few minutes of use and may cause a small

amount of fuming. This is quite normal – the fumes are non-toxic and will

quickly disappear.

We recommend that you open a window to ventilate the room when using

the heater for the rst time.

Positioning the heater

Always ensure that the heater is stood on a rm, level base near to, but

not directly beneath, a suitable mains supply socket.

Ensure that curtains and furniture are not positioned close to the chosen

position, as this would create a potential re hazard.

Product Assembly

WARNING: THE HEATER SHOULD NEVER BE USED WITHOUT THE

FEET SECURELY FITTED.

Lay the heater on its back so the underneath of the product is accessible.

Locate and remove the foot xing screw - see Fig. 2(a). Clip the foot in

place and secure using the foot xing screw - see Fig. 2(b).

Fig. 2

Controls

Indicator Neon (selected models)

The indicator neon comes on when the appliance is connected to mains

supply.

Thermostat (all models)

The thermostat controls the heat output according to the room temperature.

This ensures that the heater will not produce heat unnecessarily when the

room is warm.

To set the temperature you require, Gradually turn the thermostat knob

clockwise until the desired temperature is reached. Allow some time between

increments for the room temperature to stabilise.

Alternatively to heat a cold room quickly, turn the thermostat knob to the

Max position. When the room has reached the desired temperature, turn

the thermostat knob anti-clockwise until the thermostat clicks off. The heater

will then automatically maintain this room temperature.

The thermostat also has a frost protection setting marked ‘ ’. This setting is

useful in areas such as garages to prevent frost damage. If the thermostat is

set to its minimum setting ‘ ’, the heater will cycle ON and OFF to maintain

a temperature of approximately 5°C to help protect against frosty conditions.

Switches (selected models)

Selected models are supplied with selector switches . There are two switch

types, one is an on/off switch and the other is a heat selection switch.

Depending on model either one or both switch may be included. The switch

operation is as follows.

On/Off: O - Off

I - On

Heat selection - Low heatI

II - High heat

Mechanical Timer (selected models)

Note: The timer clock will only operate when the product is connected to

the mains supply

Operation modes

There are two operating modes on the timer, Manual operation and Auto

operation. The operation mode is set using the slide switch on the timer

- see g4.

Manual operation (Position - I)

This setting allows power to the product uninterrupted by the timer,

however other product controls will continue to function as normal.

Auto operation (Position - )

This setting allows the heater to be controlled by the timer. The

product will be switched on and off depending on the pre-set timer

program.

Fig. 3

Fig. 4

Setting the time of day

To set the time of day, rotate the timer dial clockwise (indicated by the

arrow) until the correct time of day is opposite the reference mark -

see . The 24-hour clock is used ; e.g. 4 pm is ‘16’ (16:00hrs)Fig. 4 .

Setting the ‘Auto’ ON and OFF times

To set the timer :

1. Using your nger tip or the tip of a pencil, push in as many

segments as necessary around the dial, according to the times you

don’t require heat – see . Each segment pushed in switches Fig. 5

the heater OFF for that part of the hour. All other segments will be

ON. For example, shows the timer set to switch the heater Fig. 5

OFF between 11pm and 1.45am.

2. You can select as many ON periods as you like, within the 24-hour

day. The settings will repeat every day until changed.

3. To change ON and OFF times, simply push in any ‘ON’ segments

you wish to cancel and pull out new ‘ON’ segments as required.

Switching to auto

Ensure the thermostat and/or the heat selector are set for the desired

heat output.

Check that the clock shows the correct time of day. Set the mode slide

switch to , the heater will switch ON and OFF according to the timer

settings - see .Fig. 5

Note

Remember to observe all safety warnings when operating the heater on

auto setting unattended or attended .

If the mains supply to the heater is interrupted, the timer clock will stop until

power is restored ; reset the time of day to ensure correct ON and OFF times.

Fig. 5

Turbo fan(selected models)

The turbo fan is used to boost

the airow around the room. This

circulates the heat better and

results in a reduced heat up time

and a more even heat distribution.

The turbo fan is controlled by the

neon switch on the front of the

product.

The turbo can be turned on

ind epen d entl y o f t he hea t,

however the fan will switch on

and off under the control of the

thermostat.

Note: on selected models in warm weather the fan can be used to circulate

cool air. Once the heat selection switches are in the off position and the

thermostat is set to ‘Max’ the fan will continue to function to circulate cool air.

Safety – overheat protection

For your safety, this appliance is tted with a thermal cut-out. In the event

that the product overheats, the cut-out switches the heater off automatically.

To bring the heater back into operation, remove the cause of the overheating,

then unplug or turn off the electrical supply to the heater for a few minutes.

When the heater has cooled sufciently, re-connect and switch on the

heater.

Important Notes

Although this heater is manufactured to comply with the relevant safety

standards, certain types of carpets could become discoloured by the

temperatures under a portable heater. If you are concerned about this,

we recommend that you contact the carpet manufacturer for guidance.

Alternatively, either stand the heater on a suitable base to shield the carpet

– call our Helpline for further advice.

You may notice some parts of the element appearing to be hotter from time

to time because of the variable airow through the heater. This does not

cause a safety hazard.

The heat outlet grille may become discoloured with use – this is caused by

airborne pollution and is not a fault.

Recycling

For electrical products sold within the European Community.

At the end of the electrical products useful life it should not be

disposed of with household waste.

Please recycle where facilities exist.

Check with your Local Authority or retailer for recycling advice

in your country.

Cleaning

WARNING – ALWAYS DISCONNECT FROM THE POWER SUPPLY

BEFORE CLEANING THE HEATER.

Before commencing cleaning, switch off the heater and allow it to cool.

Disconnect the electricity supply to the appliance.

The outside can be cleaned by wiping it over with a soft damp cloth and

then dried. Do not use abrasive cleaning powders or furniture polish, as

this can damage the surface nish.

Fig. 6

Product specificaties

Merk:	Dimplex
Categorie:	Niet gecategoriseerd
Model:	402TSF

Heb je hulp nodig?

Als je hulp nodig hebt met Dimplex 402TSF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dimplex

Dimplex Optiflame 3D GLN20BR3D Handleiding

15 November 2024

Dimplex GDDEU30 Handleiding

26 Februari 2024

Dimplex ALM20E Handleiding

13 November 2023

Dimplex MZT20E Handleiding

1 Juli 2023

Dimplex MZT20BL-E Handleiding

29 Juni 2023

Dimplex Optiflame 3D BMR20CH3D Handleiding

27 Juni 2023

Dimplex Optiflame 3D BMR20AB3D Handleiding

27 Juni 2023

Dimplex Optiflame 3D BMR20BR3D Handleiding

25 Juni 2023

Dimplex Optiflame 3D GLN20CH3D Handleiding

24 Juni 2023

Dimplex DXTT3 Handleiding

13 Juni 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024

Profoto RFi Softbox Octa Handleiding

24 December 2024

Koenic KAP 2523 Handleiding

24 December 2024

Philips HD9921 Handleiding

24 December 2024

Philips Senseo HD7008 Handleiding

24 December 2024

Onkyo IRK1804C Handleiding

24 December 2024