Digigram LX-MADI Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor Digigram LX-MADI (20 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/20
LX-MADI
User Manual    v1.4 Nov 2016
LX-MADI
Multichannel MADI PCI Express Sound Card
User Manual

0
LX-MADI
User Manual    v1.4 Nov 2016
Table of contents
   
1 INFORMATION FOR THE USER        
2 IMPORTANT NOTICE    
3 FEATURES  
Main hardware features    
3.2 Main software features      
3.3 MADI features    
4 REQUIREMENTS  
4.1 Minimum hardware requirements      
Software requirements  
Supported operating systems    
5 SOFTWARE INSTALLATION AND CONFIGURATION UNDER WINDOWS            
5.1 Installation under Windows operating systems          
5.2 Microsoft volume mixer panel        
5.3 ASIO driver configuration      
6 HOW TO CHECK THE INSTALLATION UNDER WINDOWS              
7 UNINSTALLING THE DRIVERS UNDER WINDOWS          
8 SPECIFICATIONS  
8.1 Configuration  
8.2 Inputs/Outputs  
8.3 Connectors  
8.4 Development environments    
9 APPENDIX  
9.1 LX-IP schematic diagram      
9.2 Connectors  


 
1
LX-MADI
User Manual    v1.4 Nov 2016
1 INFORMATION FOR THE USER
       
This device complies with part 15 of FCC rules. Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions contained in this data sheet, may cause harmful interference to radio and television communications. However, there is
no guarantee that interference will not occur in a particular installation.                   
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:                                       
● reorient or relocate the receiving antenna          
● increase the separation between the equipment and the receiver               
● connect the equipment into an outlet on a circuit different from that of the receiver                           
● consult the dealer or an experienced radio / television technician.                 
Note: Connecting


this


device


to


peripheral


devices


that


do


not


comply


with


CLASS


B requirements


or


using


an


unshielded
peripheral


data


cable


could


also


result


in harmful


interference


to


radio


or


television


reception.
To


ensure


that


the


use


of


this


product


does


not


contribute


to


interference,


it


is


necessary


to


use


shielded


I/O


cables.
The


user


is


cautioned


that


any


changes


or


modifications


not


expressly


approved


by


Digigram


could


void


the


user’s
authority


to


operate


this


equipment.
Warning:
Electrostatic discharge (ESD) can damage several components on the board. To
avoid


such


damage


in


handling


the


board,


take


the


following


precautions:
Bring the device and everything that contacts it to ground potential by providing
a conductive surface and discharge paths. As a minimum, observe these
precautions:
●Disconnect


all


power


and


signal


sources.
●Place


the


device


on


a


grounded


conductive


work


surface.
●Ground


yourself


via


a


grounding


wrist


strap


or


by


holding


a
grounded


object.
●Ground


any


tool


that


will


contact


the


device.
2 IMPORTANT NOTICE   
This card has been tested and found to comply with the following standards:                       
● International: CISPR22 Class B.     
● Europe: EMC 89/336/CEE (1992) specifications.       
● United States: FCC Rules-Part 15-Class B (digital device).             
2


Product specificaties

Merk: Digigram
Categorie: Niet gecategoriseerd
Model: LX-MADI

Heb je hulp nodig?

Als je hulp nodig hebt met Digigram LX-MADI stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Digigram

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd