Datalogic 94A151115 Handleiding

Datalogic Oplader voor mobiel apparaat 94A151115

Lees hieronder de 📖 handleiding in het Nederlandse voor Datalogic 94A151115 (2 pagina's) in de categorie Oplader voor mobiel apparaat. Deze handleiding was nuttig voor 69 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Datalogic Kyman™ Ethernet Multi Cradle

The Datalogic Kyman™ Ethernet Multi Cradle provides power for

charging up to four mobile computers simultaneously and also connects

up to four mobile computers to an Ethernet network.

Figure 1 – Datalogic Kyman™ Ethernet Multi Cradle General View

Key:

A) Link LED for Ethernet Port 1

B) Speed LED for Ethernet Port 1

C) Datalogic Kyman™ Charging Status LED

D) Power supply connector

E) Ethernet Port 1 (with integrated Link and Speed LEDs)

F) Ethernet Port 2 (with integrated Link and Speed LEDs)

822000790

The Ethernet cradle drivers are pre-installed on the Datalogic Kyman™

and initiate automatically when the Datalogic Kyman™ is placed in a

properly connected Four Slot Ethernet cradle.

When the mobile computer is inserted into the Four Slot Ethernet cradle,

the LAN icon indicates that the mobile computer is connected to a

network.

The green Speed LED lights to indicate that the transfer rate is 100 Mbps.

When it is not lit it indicates that the transfer rate is 10Mbps.

NOTE

The maximum bandwidth capacity for each Mobile

Computer is 12Mbps.

The yellow Link LED blinks to indicate activity, or stays lit to indicate that

a link is established. When it is not lit it indicates that there is no link.

The Speed LED and the Link LED integrated in Ethernet Port 1 and 2

function in the same way.

The Charging Status LED on the mobile computer shows the status of the

battery charging. The maximum time required to recharge a completely

run-down battery pack is about 3 hours for Li-Ion batteries. See Datalogic

Kyman™ User’s Manual for Charging Status LED indications.

Correct Mobile Computer Insertion / Removal

Insert the mobile computer into a slot to begin charging and start

communication.

For correct insertion onto the cradle, insert the mobile computer from the

top of the cradle and push it down firmly.

Figure 2 - Mobile Computer Insertion

To remove the mobile computer from the Datalogic Kyman™ Ethernet

Multi Cradle, simply pull it upwards while holding the cradle firmly down.

TECHNICAL FEATURES

Electrical Features

Power supply from 12 to 14 VDC ± 5%

Consumption Max 7 A

Indicators Ethernet Link LED (yellow)

Ethernet Speed LED (green)

Charge time (when PDA is off) max 3 hours (Li ION batteries)

Communication Features

Interface Ethernet 10/100 Base T

Environmental Features

Working temperature 0° to +50°C / 32° to 140°F *

Storage temperature -20° to +70°C / -4° to 158°F

Humidity 90% non condensing

Degree of protection IP20

Mechanical Features

Dimensions 480 x 137 x 190 mm

18.89 x 5.4 x 7.48 in

Weight about 2940 g / 104 oz

* Batteries must be charged at a temperature ranging from 0° to 45 °C

(+32° to 113°F).

CONNECTIONS

CAUTION

Connections should always be made with power OFF!

Ethernet Connection

Connect the Ethernet cradle (Ethernet port 1) to an Ethernet hub or a port on

the host device. Connect the Ethernet cradle (power port) to power supply.

Figure 3 - Ethernet Connection

Key:

A) Datalogic Kyman™ Ethernet Multi Cradle

B) 94ACC1337 FPS19 W/O Power Cord

94ACC1150 Power cord EU 3-pin

C) UTP CAT 5E cable (recommended use)

D) Ethernet hub

Daisychaining Ethernet Connection

To connect several cradles to an Ethernet network, Ethernet cradles may be

daisychained. It is recommended not to connect more than 4 cradles in order

to maintain the optimal baud rate. The Speed LED and the Link LED on the

Ethernet Port 2 function in the same way as the Speed LED and the Link LED

on the front of the cradle.

To daisychain cradles:

1. Connect the first Ethernet cradle to power and to the Ethernet Switch as

shown on Figure 4.

2. Connect power to the second Ethernet cradle.

3. Connect the daisychain Ethernet cable (either straight or twisted cable

can be used) between Ethernet Port 2 of the first cradle, and Ethernet

Port 1 of the second cradle.

4. Connect additional cradles as shown in Figure 4.

Figure 4 - Daisychaining Ethernet Connection

Key:

A) Ethernet hub

B) Ethernet Port 1

C) Ethernet Port 2

D) 94ACC1337 FPS19 W/O Power Cord

94ACC1150 Power cord EU 3-pin

E) UTP CAT 5E cable (recommended use).

Power Supply

Each Ethernet Multi Cradle requires a power supply to be connected to

the cradle. We recommend the DL FPS19 power supply.

Figure 5 - Power Supply Polarity

COMPLIANCE

WEEE Compliance

DATALOGIC MOBILE S.r.l.

Via S. Vitalino, 13

40012 - Lippo di Calderara

Bologna - Italy 06

dichiara che

declares that the

déclare que le

bescheinigt, daß das Gerät

declare que el

KYMAN Ethernet Desk Multi Cradle

e tutti i suoi modelli

and all its models

et tous ses modèles

und seine Modelle

y todos sus modelos

sono conformi alle Direttive del Consiglio Europeo sottoelencate:

are in conformity with the requirements of the European Council Directives listed below:

sont conformes aux spécifications des Directives de l'Union Européenne ci-dessous:

den nachstehenden angeführten Direktiven des Europäischen Rats:

cumple con los requisitos de las Directivas del Consejo Europeo, según la lista siguiente:

89/336/EEC EMC Directive e 92/31/EEC, 93/68/EEC emendamenti successivi

and further amendments

et ses successifs amendements

und späteren Abänderungen

y succesivas enmiendas

Basate sulle legislazioni degli Stati membri in relazione alla compatibilità elettromagnetica ed alla

sicurezza dei prodotti.

On the approximation of the laws of Member States relating to electromagnetic compatibility and product

safety.

Basée sur la législation des Etats membres relative à la compatibilité électromagnétique et à la sécurité

des produits.

Über die Annäherung der Gesetze der Mitgliedsstaaten in bezug auf elektromagnetische Verträglichkeit

und Produktsicherheit entsprechen.

Basado en la aproximación de las leyes de los Países Miembros respecto a la compatibilidad

electromagnética y las Medidas de seguridad relativas al producto.

Questa dichiarazione è basata sulla conformità dei prodotti alle norme seguenti:

This declaration is based upon compliance of the products to the following standards:

Cette déclaration repose sur la conformité des produits aux normes suivantes:

Diese Erklärung basiert darauf, daß das Produkt den folgenden Normen entspricht:

Esta declaración se basa en el cumplimiento de los productos con la siguientes normas:

EN 55022 (C LASS A ITE), AUGUST 1994:

AMENDMENT A1 (CLASS A ITE), OCTOBER 2000:

LIMITS AND METHODS OF MEASUREMENTS OF RADIO

DISTURBANCE OF INFORMATION TECHNOLOGY EQUIPMENT

EN 55024, S EPTEMBER 1998: INFORMATION TECHNOLOGY EQUIPMENT. IMMUNITY

CHARACTERISTICS

. LIMITS AND METHODS OF

MEASUREMENTS

Lippo di Calderara, May 19th, 2007

Paola Chientaroli

Quality Assurance Manager

C B

Product specificaties

Merk:	Datalogic
Categorie:	Oplader voor mobiel apparaat
Model:	94A151115
Kleur van het product:	Zwart
Gewicht:	2940 g
LED-indicatoren:	Ja
Ingangsspanning:	12/14 V
Compatibiliteit:	Kyman
Aansluiting(en):	Ethernet 10/100Base-T
Type oplader:	Binnen
Lader compatibiliteit:	PDA
Afmetingen (B x D x H):	480 x 137 x 190 mm
Bedrijfstemperatuur (T-T):	0 - 50 °C