Daikin FTXM50R Handleiding

Daikin Airco FTXM50R

Lees hieronder de 📖 handleiding in het Nederlandse voor Daikin FTXM50R (12 pagina's) in de categorie Airco. Deze handleiding was nuttig voor 44 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

Installation manual

Daikin room air conditioner English

Installation manual

Daikin room air conditioner

CTXM15R2V1B

CTXM15R5V1B

FTXM20R2V1B

FTXM20R5V1B

FTXM25R2V1B

FTXM25R5V1B

FTXM35R2V1B

FTXM35R5V1B

FTXM42R2V1B

FTXM42R5V1B

FTXM50R2V1B

FTXM60R2V1B

FTXM71R2V1B

ATXM20R2V1B

ATXM20R5V1B

ATXM25R2V1B

ATXM25R5V1B

ATXM35R2V1B

ATXM35R5V1B

ATXM50R2V1B

Table of contents

Installation manual

CTXM15+FTXM20~42+ATXM20~35R2/5V1B +

FTXM50~71R2V1B + ATXM50R2V1B

Daikin room air conditioner

3P482320-11R – 2020.06

Table of contents

1 About the documentation 2

1.1 About this document.................................................................. 2

2 Specific installer safety instructions 2

3 About the box 3

3.1 Indoor unit ................................................................................. 3

3.1.1 To remove the accessories from the indoor unit......... 3

4 About the unit 3

4.1 About the wireless LAN ............................................................. 4

4.1.1 Precautions when using the wireless LAN.................. 4

4.1.2 Basic parameters ........................................................ 4

5 Unit installation 4

5.1 Preparing the installation site .................................................... 4

5.1.1 Installation site requirements of the indoor unit .......... 4

5.2 Opening the indoor unit ............................................................. 4

5.2.1 To remove the front panel........................................... 4

5.2.2 To open the service cover........................................... 4

5.2.3 To remove the front grille ............................................ 4

5.3 Mounting the indoor unit............................................................ 5

5.3.1 To install the mounting plate....................................... 5

5.3.2 To drill a wall hole ....................................................... 6

5.3.3 To remove the pipe port cover.................................... 6

5.4 Connecting the drain piping....................................................... 6

5.4.1 To connect the piping on right side, right-back, or

right-bottom ................................................................. 6

5.4.2 To connect the piping on left side, left-back, or left-

bottom ......................................................................... 7

5.4.3 To check for water leaks............................................. 7

6 Piping installation 7

6.1 Preparing refrigerant piping....................................................... 7

6.1.1 Refrigerant piping requirements.................................. 7

6.1.2 Refrigerant piping insulation ....................................... 7

6.2 Connecting the refrigerant piping .............................................. 8

6.2.1 To connect the refrigerant piping to the indoor unit .... 8

7 Electrical installation 8

7.1 Specifications of standard wiring components .......................... 8

7.2 To connect the electrical wiring to the indoor unit ..................... 8

8 Finishing the indoor unit installation 9

8.1 To insulate the drain piping, refrigerant piping and

interconnection cable ................................................................ 9

8.2 To pass the pipes through the wall hole.................................... 9

8.3 To fix the unit on the mounting plate ......................................... 9

8.4 To close the indoor unit ............................................................. 9

8.4.1 To re-install the front grille .......................................... 9

8.4.2 To close the service cover .......................................... 10

8.4.3 To re-install the front panel ......................................... 10

9 Commissioning 10

9.1 Checklist before commissioning................................................ 10

9.2 To perform a test run................................................................. 10

9.2.1 To perform a test run using the user interface............ 10

10 Technical data 10

10.1 Wiring diagram .......................................................................... 10

10.1.1 Unified wiring diagram legend..................................... 10

1 About the documentation

1.1 About this document

INFORMATION

Make sure that the user has the printed documentation and

ask him/her to keep it for future reference.

Target audience

Authorised installers

INFORMATION

This appliance is intended to be used by expert or trained

users in shops, in light industry, and on farms, or for

commercial and household use by lay persons.

Documentation set

This document is part of a documentation set. The complete set

consists of:

▪General safety precautions:

▪ Safety instructions that you MUST read before installing

▪ Format: Paper (in the box of the indoor unit)

▪Indoor unit installation manual:

▪ Installation instructions

▪ Format: Paper (in the box of the indoor unit)

▪Installer reference guide:

▪ Preparation of the installation, good practices, reference data,…

▪ Format: Digital files on http://www.daikineurope.com/support-

and-manuals/product-information/

Latest revisions of the supplied documentation may be available on

the regional Daikin website or via your dealer.

The original documentation is written in English. All other languages

are translations.

Technical engineering data

▪ A of the latest technical data is available on the regionalsubset

Daikin website (publicly accessible).

▪ The of latest technical data is available on the Daikinfull set

Business Portal (authentication required).

2 Specific installer safety

instructions

Always observe the following safety instructions and regulations.

Unit installation (see ["5Unit installation"44])

WARNING

The appliance shall be stored in a room without

continuously operating ignition sources (example: open

flames, an operating gas appliance or an operating electric

heater).

WARNING

Do NOT place objects below the indoor and/or outdoor unit

that may get wet. Otherwise condensation on the main unit

or refrigerant pipes, air filter dirt or drain blockage may

cause dripping, and objects under the unit may get dirty or

damaged.

3 About the box

Installation manual

CTXM15+FTXM20~42+ATXM20~35R2/5V1B +

FTXM50~71R2V1B + ATXM50R2V1B

Daikin room air conditioner

3P482320-11R – 2020.06

CAUTION

For walls containing a metal frame or a metal board, use a

wall embedded pipe and wall cover in the feed-through

hole to prevent possible heat, electrical shock, or fire.

Piping installation (see ["6Piping installation"47])

DANGER: RISK OF BURNING/SCALDING

CAUTION

▪ Use the flare nut fixed to the unit.

▪ To prevent gas leakage, apply refrigeration oil only to

the inside of the flare. Use refrigeration oil for R32.

▪ Do NOT reuse joints.

CAUTION

▪ Do NOT use mineral oil on flared part.

▪ NEVER install a drier to this R32 unit to guarantee its

lifetime. The drying material may dissolve and damage

the system.

CAUTION

▪ Incomplete flaring may cause refrigerant gas leakage.

▪ Do NOT re-use flares. Use new flares to prevent

refrigerant gas leakage.

▪ Use flare nuts that are included with the unit. Using

different flare nuts may cause refrigerant gas leakage.

Electrical installation (see ["7Electrical installation"48])

DANGER: RISK OF ELECTROCUTION

WARNING

▪ All wiring MUST be performed by an authorised

electrician and MUST comply with the applicable

legislation.

▪ Make electrical connections to the fixed wiring.

▪ All components procured on-site and all electrical

construction MUST comply with the applicable

legislation.

WARNING

▪ If the power supply has a missing or wrong N-phase,

equipment might break down.

▪ Establish proper earthing. Do NOT earth the unit to a

utility pipe, surge absorber, or telephone earth.

Incomplete earthing may cause electrical shock.

▪ Install the required fuses or circuit breakers.

▪ Secure the electrical wiring with cable ties so that the

cables do NOT come in contact with sharp edges or

piping, particularly on the high-pressure side.

▪ Do NOT use taped wires, stranded conductor wires,

extension cords, or connections from a star system.

They can cause overheating, electrical shock or fire.

▪ Do NOT install a phase advancing capacitor, because

this unit is equipped with an inverter. A phase

advancing capacitor will reduce performance and may

cause accidents.

WARNING

ALWAYS use multicore cable for power supply cables.

WARNING

Use an all-pole disconnection type breaker with at least

3 mm between the contact point gaps that provide full

disconnection under overvoltage category III.

WARNING

If the supply cord is damaged, it MUST be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

WARNING

Do NOT connect the power supply to the indoor unit. This

could result in electrical shock or fire.

WARNING

▪ Do NOT use locally purchased electrical parts inside

the product.

▪ Do NOT branch the power supply for the drain pump,

etc. from the terminal block. This could result in

electrical shock or fire.

WARNING

Keep the interconnection wiring away from copper pipes

without thermal insulation as such pipes will be very hot.

3 About the box

3.1 Indoor unit

3.1.1 To remove the accessories from the

indoor unit

1Remove:

▪ the accessory bag located at the bottom of the package,

▪ the mounting plate attached to the back of the indoor unit,

▪ the spare SSID sticker located on the front grille.

1×1× 2× 2× 2×1× 1× 1×1× 1× 1×

fe1d e2ba c g h i j

aInstallation manual

bOperation manual

cGeneral safety precautions

dSpare SSID sticker

e1 Class 15~42: Silver allergen removal air purifying filter

(without frame)

e2 Class 50~71: Titanium apatite deodorising filter and

silver allergen removal air purifying filter (with frame)

fIndoor unit fixing screw (M4×12L). Refer to "8.3To fix the

unit on the mounting plate"[49].

gDry battery AAA.LR03 (alkaline) for user interface

hUser interface holder

iUser interface

jMounting plate

▪ Do NOT throw away the spare sticker. KeepSpare SSID sticker.

it in a safe place in case it is needed in future (e.g. in case the

front grille was replaced attach it to the new front grille).

4 About the unit

WARNING: MILDLY FLAMMABLE MATERIAL

The refrigerant inside this unit is mildly flammable.

Product specificaties

Merk:	Daikin
Categorie:	Airco
Model:	FTXM50R

Heb je hulp nodig?

Als je hulp nodig hebt met Daikin FTXM50R stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Airco Daikin

Daikin Zena FTXJ60T2VMAK Handleiding

4 December 2024

Daikin ATXF20D5V1B Handleiding

4 December 2024

Daikin FVXS35FV1B Handleiding

4 December 2024

Daikin ARC433A103 Handleiding

15 November 2024

Daikin RXP60N5V1B9 Handleiding

22 Oktober 2024

Daikin SV8A14AJV1B Handleiding

22 Oktober 2024

Daikin RXZ50NV1B Handleiding

22 Oktober 2024

Daikin RTSYQ10PAY1 Handleiding

22 Oktober 2024

Daikin FFQ35B9V1B Handleiding

22 Oktober 2024

Daikin RXP50N5V1B9 Handleiding

22 Oktober 2024

Handleiding Airco

Nieuwste handleidingen voor Airco

LG PM12EP Handleiding

21 December 2024

Svan SAAS1200W Handleiding

20 December 2024

Argoclima LOKI PLUS WF Handleiding

18 December 2024

Universal Blue Grandvalira II 1750 Handleiding

18 December 2024

Universal Blue Grandvalira II 3000 Handleiding

18 December 2024

Mitsubishi WRK20MB2 Handleiding

14 December 2024

Mitsubishi SKM25ZSP-W Handleiding

14 December 2024

Mitsubishi MSZ-GV2217 Handleiding

14 December 2024

Mitsubishi WRK53MB2 Handleiding

14 December 2024

Mitsubishi SRK20ZSX-S Handleiding

14 December 2024