Da-Lite ViewShare Tensioned Advantage Electrol 24055LS Handleiding

Da-Lite Projectiescherm ViewShare Tensioned Advantage Electrol 24055LS

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite ViewShare Tensioned Advantage Electrol 24055LS (12 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTRUCTION BOOK FOR

ViewShare Tensioned

Advantage Electrol

Tools Required for Installation

1. Hang case and attach to support structure with bolts.

See Suggested Methods of Installation.

2. Tighten bolts until trim lange is lush with ceiling.

NOTE: For proper operation, screen assembly must be level

after installation.

3. Remove 2 screws to open junction box. Install electrical

connections that apply to your unit. Make sure to review the

wiring diagram for proper hook up. Replace junction box cover

and secure with 2 screws.

NOTE: Must be installed in accordance with the requirements of

the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

If your case was ordered in advance of the screen and roller

assembly, your installation is now complete. Continue to

step 4 if your Tensioned Advantage Electrol was ordered as a

complete unit.

4. Use supplied 1/8" hex key to remove silver shipping brackets

attached to slat and screen case.

5. Test installation by running screen up and down a few times.

Be prepared to stop screen should any objects obstruct the

movement of the screen. To prevent damage to the motor, the

standard duty cycle is 1 minute on and 3 minutes of.

Case Installation

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

Save These Instructions

Pre-Installation

1. Carefully unpack case from shipping carton.

2. Set aside the Installation Kit. Items inside will be used during

installation.

3. Make sure to recheck measurement of case for proper

installation clearance.

4. Remove any protective foam covering the outside of

the case.

5. For shipping purposes, foam is also inserted between the roller

brackets and endcaps (Figure 1). Remove these foam blocks from

the ends.

6. Remove the hanger brackets from the top of the case using a 1/2”

wrench. Do not discard the hardware; it will be used during case

installation to re-attach the hanger brackets for mounting.

1/2“ Open Wrench

or Socket Driver

1/8” Hex Key

(included)

Suggested Methods of Installation

⅜" Threaded Rod

(Not Supplied)

Hanger Bracket

Electrical

Junction Box

Motor

End

Variable Position

Mounting Bracket

Audience Side

6 ⁄"

6 ⁄"

7 ¾"

⅜" Threaded Rod

(Not Included)

Attached To

Mounting Bracket

Self-Trimming

Flange Finished

Ceiling

7 ¾"

6 ⁄"

6 ⅜"

3 ⁄"

7 ⁄"

6 ⁄"

Method 1

Method 2

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	ViewShare Tensioned Advantage Electrol 24055LS

Heb je hulp nodig?

Als je hulp nodig hebt met Da-Lite ViewShare Tensioned Advantage Electrol 24055LS stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag