Da-Lite Tensioned Dual Masking Electrol Handleiding

Da-Lite Projectiescherm Tensioned Dual Masking Electrol

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Tensioned Dual Masking Electrol (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 24 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: info@da-lite.com

Instruction Book for

TENSIONED DUAL MASKING ELECTROL®

The Da-Lite Difference.

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rat-

ing at least equal to that of the appliance should be used.

Cords rated for less amperage than the appliance may over-

heat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of fire, electric shock, or

injury to persons.

SAVE THESE INSTRUCTIONS

PRE-INSTALLATION

1. Carefully unpack screen and remove outer wrapping from case.

2. Make sure to recheck measurements of screen location before installation.

3. Remove center support brackets (on 8' and wider screens only), reverse brackets and reinstall flush with the top of the

box.

INSTALLATION

1. Install screen by raising unit into position between joists at one end only. Install one lag screw in each mounting

bracket.

2. Level unit lengthwise with a carpenter’s level and plumb level. Secure opposite end.

CAUTION! Do not seal in until screen has been secured in position and properly tested for satisfactory operation.

3. Carefully remove three shipping brackets by removing six hex head screws from case and three phillips head

screws from aluminum slat. Use a phillips screwdriver, a hex socket and a ratchet. Slat should move freely (Fig. 1).

4. Detach access panel by removing screws (Fig. 1).

5. Remove junction box cover plate.

6. Install electric hook up that applies to your unit. Make sure to review your electrical installation checklist and wiring

diagram (included) for either 120 volt switch, 220/240 volt switch or low voltage control.

NOTE: Must be installed in accordance with the requirements of the Local Building Codes, the Canadian Electrical Code (CEC),

CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.

CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.

7. Carefully remove two wood boards securing mask surface to case.

8. Test installation by carefully running picture and mask surfaces up and down several times. Be prepared to stop

screen. Standard Duty Cycle: 1 MIN. ON / 3 MIN. OFF.

NOTE: When rolled down, the picture surface should wrap fully around the roller. No part of the roller should be exposed.

Picture and mask surfaces will automatically stop in the down position.

The mask will start down off the front of the roller, travel completely down past the bottom of the viewing surface,

then “step back” against the viewing surface to eliminate shadowing by rolling up the back side of the roller. Do not

adjust the limits to change this feature.

9. Run the picture and mask surfaces upward. When the picture and mask surfaces are fully up the limit switches (in

the motors) are tripped and the motors shut off.

10. Check for satisfactory condition by operating screen a few times. Reinstall access panel.

FIGURE 1 FIGURE 2

DRYWALL

SCREW

ACCESS PANEL

MACHINE SCREW

PHILLIPS HEAD SCREW

SHIPPING BRACKET

PICTURE SURFACE

MASK SURFACE

MASK MOTOR

SCREEN MOTOR

HEX HEAD SCREW

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Tensioned Dual Masking Electrol
Gewicht:	- g
Oorspronkelijke beeldverhouding:	4:3
Kleur behuizing:	Zwart
Diagonaal:	145 "
Totale grootte van het scherm (hoogte x breedte):	175 x 325 cm
Schermgain:	1.3
Case L1:	393 mm