Da-Lite Large Advantage Deluxe Electrol 36861 Handleiding

Da-Lite Projectiescherm Large Advantage Deluxe Electrol 36861

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Large Advantage Deluxe Electrol 36861 (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: info@da-lite.com

The Da-Lite Difference.

Instruction Book for

LARGE ADVANTAGE® DELUXE ELECTROL®

PRE-INSTALLATION

CASE INSTALLATION

1. The case provides multiple attachment points for bolts, cables, or threaded rod. Page 5 shows threaded rod

installed. The variable position-mounting bracket may be located anywhere along the length of the case. It is

recommended to keep the brackets spaced evenly enough to distribute the weight of the screen. One mounting

bracket is required for every 4' of case length.

The case has a self-trimming flange around the bottom. Ceiling tiles or drywall may be placed on top of this flange

to provide a finished appearance.

2. After securing the case in the ceiling check that the case is level and plumb.

3. Install electrical connections that apply to your unit. Review the wiring diagrams on page 4 for proper installation.

1. Carefully unpack screen and remove outer wrapping from case.

2. Make sure to recheck measurements of screen location before installation.

Please Note: Motor Operator Projection Screen Models LADT, LADDT, LAD

and LADD must be installed in accordance with the requirements of the

Local Building Codes, the Canadian Electrical Code (CEC), CAN/CSA C22.1

and the National Electric Code (NEC), NFPA 70. An appropriate disconnect

device shall be provided as part of the building installation.

IMPORTANT SAFETY INSTRUCTIONS

When using your video equipment, basic safety precautions should always be followed, including the

following:

1. Read and understand all instructions before using.

2. Close supervision is necessary when any appliance is used by or near children. Do not leave

appliance unattended while in use.

3. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged –

until it has been examined by a qualified serviceman.

4. Position the cord so that it will not be tripped over, pulled, or contact hot surfaces.

5. If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance

should be used. Cords rated for less amperage than the appliance may overheat.

6. To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.

7. To reduce the risk of electric shock, do not disassemble this appliance. Contact an authorized

service dealer when repair work is required. Incorrect reassembly can cause electric shock when

the appliance is used subsequently.

8. The use of an accessory attachment not recommended by the manufacturer may cause a risk of

fire, electric shock, or injury to persons.

SAVE THESE INSTRUCTIONS

BOLTS

ACCESS

DOOR

FIGURE 1

DOOR SUPPORT SCREWS

(NOT ALL SIZES)

If your screen was shipped with the motor and roller already installed proceed to step 7.

1. Remove four bolts from ends of door assembly (2 bolts on each end) (Fig. 1). This will allow the door assembly to

drop open for access to case. For larger sizes, you will also need to remove the door support screws.

2. Carefully unpack screen and roller assembly. Leave packing paper on the roller.

3. Remove the square peg bracket from the motor end of the roller assembly.

4. Remove the safety clip from the motor attachement bracket located in the motor end of the screen housing.

5. Place the roller assembly into the case with the motor on the left side. The limit switches should be facing down.

Line up the head of the motor with the motor attachment bracket.

6. Loosen four bolts that secure pin end mounting bracket into housing. Lift pin end of roller into position and slide

the bracket into the roller pin. Tighten all four bolts.

7. Complete electrical hook-up by snapping motor 1/3 wire connectors into case connectors.

8. Return to motor end and insert safety clip over casting bracket to secure motor end.

CAUTION! DO NOT CUT TAPE ON FABRIC WITH A KNIFE OR ANY SHARP TOOL. REMOVE BY HAND.

9. Carefully remove tape strips securing picture surface around roller. Slat should move freely (Fig. 2). (Only if the

roller assembly is pre installed.)

10. Test installation by operating the screen several times. Be prepared to stop the screen. The door assembly will not

close until the wall switch is placed in the up position and when the screen motor stops at its limit switch in the up

direction.

NOTE: Unit duty cycle is 1 minute on, 3 minutes off.

NOTE: Excessive continuous operation may cause the motor to overheat. If this happens the motor will shut off until it cools to

a normal operating temperature.

11. Close door assembly and replace four bolts at ends of door (2 bolts on each end) (Fig. 1).

SCREEN AND ROLLER ASSEMBLY INSTALLATION

SCREEN MOTOR

FIGURE 2

DUAL MOTOR LVC

CONTROL BOX

SCREEN MOTOR

LIMIT SWITCHES

DOOR MOTOR

LIMIT SWITCHES ACCESS DOOR

ASSEMBLY

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Large Advantage Deluxe Electrol 36861
Oorspronkelijke beeldverhouding:	16:9
Montagewijze:	Plafond/muur
Aantal per verpakking:	1 stuk(s)
Gemakkelijk te installeren:	Ja
Zichtbare schermhoogte (h):	3380 mm
Zichtbare schermbreedte (b):	5990 mm
Diagonaal:	271 "
Type aandrijving:	Gemotoriseerd
Totale grootte van het scherm (hoogte x breedte):	338 x 599 cm
Formaat:	HDTV
Zwarte achterzijde:	Ja