Da-Lite Horizon Electrol 96214S Handleiding
Da-Lite
Projectiescherm
Horizon Electrol 96214S
Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Horizon Electrol 96214S (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
INSTRUCTION BOOK FOR
Horizon Electrol®
2
1. Install screen by raising unit into position between joists at one
end only. Install one lag screw in each mounting bracket.
2. Level unit lengthwise with a carpenter’s level and plumb level.
Secure opposite end.
3. Detach access panel by removing screws (Figure 1).
CAUTION! Do not seal in until screen has been secured in
position and properly tested for satisfactory operation.
ATTENTION! Ne ixez pas l'écran jusqu'à ce qu'il ait été
correctement mis en place et qu'il fonctionne
convenablement.
4. Remove the two screws holding the splitter junction box (Figure 2).
5. Unwrap the supplied 25 ft. RJ14 cord. Plug one end into a QEYE
port on the primary splitter (see wiring diagram).
6. Run the 25 ft. RJ14 card to the back of the wall keypad and plug
into the RJ receptacle.
7. Remove the two screws holding the junction box cover plate.
Install the electrical hookup (see wiring diagram).
NOTE: Must be installed in accordance with the requirements of
the Local Building Codes, the Canadian Electrical Code (CEC),
CAN/CSA C22.1 and the National Electric Code (NEC), NFPA 70.
8. After the electrical connections are completed, replace the
junction box cover plate.
9. Carefully remove tape strips securing picture surface around roller.
CAUTION! Do not cut tape on fabric with knife or any sharp
tool. Pull orange string.
ATTENTION! Ne coupez pas le ruban adhésif sur la toile avec
un couteau ou un outil tranchant. Tirez sur le cordon orange.
10. Carefully remove wood boards securing mask surface to case.
11. Test installation by carefully running picture surface and mask
surfaces up and down several times. Be prepared to stop the
screen. IMPORTANT: Read operating instructions before
testing screen.
NOTE: When rolled down, the picture surface should wrap fully
around the roller. No part of the roller should be exposed. Picture
surface and mask surfaces will automatically stop in the down
position.
CAUTION! Excessive continuous operation may cause
overheating. If this happens, the motors will shut of until they
cool to a normal operating temperature. Duty Cycle of screen
is 1 Min. ON / 3 Min Of.
ATTENTION! Le fonctionnement continu et excessif peut
provoquer une surchaufe.Si cela se produit, les moteurs
s'arrêteront jusqu'à qu'ils se soient refroidis à la température
normale de fonctionnement. Le cycle de fonctionnement est
de 1 min. en marche / 3 min. à l'arrêt.
Pre-Installation
Installation
1. Carefully unpack screen and remove outer wrapping
from case.
Figure 2
Figure 1
Drywall Screw
Access Panel
Machine Screw
Truss Head Screw
Shipping Bracket
Hex Head Screw
Tape Strips
Picture Surface
Slats
Mask Surface
Mask
Motor
Screen
Motor
Junction Box
Splitter
Junction
Box
2. Make sure to recheck measurements of screen location
before installation.
Important Safety Instructions
When using your video equipment, basic safety precautions should always be followed, including the following:
1. Read and understand all instructions before using.
2. Position the cord so that it will not be tripped over, pulled, or
contact hot surfaces.
3. If an extension cord is necessary, a cord with a current rating at
least equal to that of the appliance should be used. Cords rated
for less amperage than the appliance may overheat.
4. To reduce the risk of electric shock, do not disassemble this
appliance. Contact an authorized service dealer when repair
work is required. Incorrect reassembly can cause electric shock
when the appliance is used subsequently.
5. The use of an accessory attachment not recommended by the
manufacturer may cause a risk of ire, electric shock, or injury to
persons.
Save These Instructions
3
Screen Operation
The Horizon has been preset to three or four diferent formats. The screen can be set to any format by pressing the corresponding
button on the keypad. Below is a list of each button function.
IMPORTANT! When operating the switch, press and release buttons. Do not hold the button for more than
three (3) seconds or the button will be reprogrammed to the current screen position.
Native NTSC (1.33:1) Format Screens
1. Lowers screen to NTSC (1.33:1) format. Mast will travel down and
reverse wrap on the roller. The mask it not used for this format.
2. Sets format to HDTV (1.78:1).
3. Sets format to Letterbox (1.85:1).
4. Sets format to Cinemascope (2.35:1).
Native HDTV (1.78:1) Format Screens
1. Lowers screen to HDTV (1.78:1) format. Mast will travel down and
reverse wrap on the roller. The mask it not used for this format.
2. Sets format to Letterbox (1.85:1).
3. Sets format to Cinemascope (2.35:1).
4. Open: User deined preset.
Stop – Stops the screen and mask movement at any position when pressed.
Up – Returns the screen and mask to the up position.
Screen – Runs the screen up and down without mask movement.
Mask – Runs the mask up and down without screen movement.
Wall Keypad
Transmitter
Dual IR/RF
Remote
Format Selection
1 2 3 4
Screen Mask
Up
Stop
Format Selection
1 2 3 4
Screen Mask
Up
Stop
Product specificaties
| Merk: | Da-Lite |
| Categorie: | Projectiescherm |
| Model: | Horizon Electrol 96214S |
Heb je hulp nodig?
Als je hulp nodig hebt met Da-Lite Horizon Electrol 96214S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Projectiescherm Da-Lite
7 Augustus 2024
24 Juni 2023
4 Juni 2023
31 Mei 2023
30 Mei 2023
25 Mei 2023
21 Mei 2023
Handleiding Projectiescherm
- Projectiescherm Duronic
- Projectiescherm Elite
- Projectiescherm GPX
- Projectiescherm Kodak
- Projectiescherm Nec
- Projectiescherm Pyle
- Projectiescherm Vestel
- Projectiescherm Optoma
- Projectiescherm Oregon Scientific
- Projectiescherm Luxburg
- Projectiescherm Draper
- Projectiescherm AV:link
- Projectiescherm Projecta
- Projectiescherm Elite Screens
- Projectiescherm EluneVision
- Projectiescherm Celexon
- Projectiescherm Lumene
- Projectiescherm Stewart
- Projectiescherm Avers
- Projectiescherm Instaal
- Projectiescherm Elite ProAV
- Projectiescherm KHOMO GEAR
- Projectiescherm EPV
Nieuwste handleidingen voor Projectiescherm
18 Augustus 2024
18 Augustus 2024
20 Juni 2024
20 Juni 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024
4 Mei 2024