Da-Lite Da-Snap Handleiding

Da-Lite Projectiescherm Da-Snap

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Da-Snap (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: info@da-lite.com

Instruction Book for

DASNAP SCREEN

The Da-Lite Difference.

1. Unpack the frame parts from the carton. DO NOT

unroll the screen surface at this time.

2. Slide the frame pieces together at corners. (Note:

Frame assembly holes may not appear to fit properly

at the corners until all fasteners have been attached.

Once fasteners are attached, the frame corners will

be drawn in for a proper fit.) Secure frame pieces

with #10 screws provided. Do not tighten screws

until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”.

Be sure the frame pieces are assembled according to the

labels. This will ensure the snap pattern on the frame and

screen surface will match.

FRAME ASSEMBLY

FIGURE 1. REAR VIEW

SNaP STuD

SIDE

#10 BLaCK SCREW

SIDE

TOP

BOTTOM

SNaP STuD

LARGE WALL BRACKET (47" LONG)

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________

Screens over 96" viewing width = 3

Installation screws not included

SMALL WALL BRACKET (8" LONG)

Quantity of 1. Only for screens

80" and smaller viewing width QUANTITY INCLUDED __________

Installation screws not included

SNAP STUD

QUANTITY INCLUDED ________

#10 SCREW

QUANTITY INCLUDED ________

FRAME BRACKET

Quantities vary by screen size

Screens 80" and smaller viewing width = 3

Screens over 80" to 96" viewing width = 4

Screens over 96" viewing width = 6

QUANTITY INCLUDED ________________________________

HIGH POWER® FRAME BRACKET

Screens with High Power® viewing surface quantity = 2

Screens with 2-piece side frame rails quantity = 2

Screens 10' to 16' viewing width = 2

QUANTITY INCLUDED ________________________________

USE INSTALLATION

METHOD NUMBER __________

There are four methods of installation based on the size

of the screen and type of viewing surface. Measure the

width of the viewing area of your screen and refer to the

appropriate method of installation below. The wall

bracket diagram shows the type and quantity of bracket

that is supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power® viewing

surface.

INSTALLATION

4. Attach the small wall bracket to the wall. Refer to

Figure 4 for proper orientation. Do not tighten the

screws completely. The bracket should slide up and

down easily.

5. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the inside of

the roll. Place the frame over the screen surface, and

while lifting the frame with one hand, snap the

screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

6. Hang the screen on the brackets by hooking the

bottom of the frame onto the small wall bracket and

lift up until you can hook the top of the frame on the

top bracket. Push down on the frame to seat it on the

brackets. Refer to Figure 4.

OvERaLL hEIghT - 1-3/8"

OvERaLL

hEIghT

LIFT

WaLL

1. Use the supplied #10 screws to attach three frame

brackets to the back of the frame as shown in Figure

2. Secure the large wall bracket to wall studs at the

desired height. Make sure the bracket is level. The

top of the frame will be 1/8" above the top of the wall

bracket when mounted. You will need at least 5/8"

clearance above the bracket to hang the screen.

3. To install the small wall bracket, you must measure

the overall height of the screen frame and subtract

1-3/8". Using that dimension, measure down from the

top edge of the large wall bracket and mark the wall

for two screw holes. The holes should be centered

within the frame and 6" apart. Refer to Figure 3.

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

FIGURE 2

FRaME BRaCKETS

3-PIECES

#10 SCREWS

6-PIECES

LaRgE WaLL

BRaCKET

1-PIECE

SMaLL WaLL BRaCKET

1-PIECE

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

FIGURE 3

FIGURE 4

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Da-Snap
Oorspronkelijke beeldverhouding:	16:10
Zichtbare schermhoogte (h):	2030 mm
Zichtbare schermbreedte (b):	1270 mm
Diagonaal:	94 "
Formaat:	Video