Da-Lite Da-Mat Handleiding

Da-Lite Projectiescherm Da-Mat

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Da-Mat (6 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

DA-LITE SCREEN COMPANY, INC.

3100 North Detroit Street

Post Office Box 137

Warsaw, Indiana 46581-0137

Phone: 574-267-8101

800-622-3737

Fax: 574-267-7804

Toll Free Fax: 877-325-4832

www.da-lite.com

e-mail: info@da-lite.com

POWER

PRESENTATION PRODUCTS

The

Instruction Book for

CINEMA CONTOUR®SCREEN

1. Unwrap the frame pieces. Assemble frame pieces on padding

material or other soft, clean surface. This will help keep the

frame clean and protect it from scratches.

2. Slide the frame pieces together at corners (Note: Frame

assembly holes may not appear to fit properly at the corners

until all fasteners have been attached. Once fasteners are

attached, the frame corners will be drawn in for a proper fit.)

Secure frame pieces with #10 screws provided. Do not

tighten screws until all are started, then tighten. See Figure 1.

NOTE: The frame pieces are labeled “top” and “bottom”. Be sure

the frame pieces are assembled according to the labels. This will

ensure the snap pattern on the frame and screen surface will

match.

3. Attach the eight snap studs to the back of the frame in the

predrilled holes.

FRAME ASSEMBLY

FIGURE 1 (REAR VIEW)

SCREWS

SNAPS

LARGE WALL BRACKET (47" LONG)

Quantities vary by screen size:

Screens 80" and smaller viewing width = 1

Screens over 80" to 96" viewing width = 2 QUANTITY INCLUDED __________

Screens over 96" viewing width = 3

Installation screws not included

SMALL WALL BRACKET (8" LONG)

Quantity = 1. Only for screens

80" and smaller viewing width. QUANTITY INCLUDED __________

Installation screws not included

SNAP STUD

QUANTITY INCLUDED ________

#10 SCREW

QUANTITY INCLUDED ________

HIGH POWER®FRAME BRACKET

Screens with High Power®quantity = 2

Screens with 2-piece side frame rails quantity = 2

QUANTITY INCLUDED ________________________________

USE INSTALLATION

METHOD NUMBER __________

2. To install the lower wall bracket, you must measure

the overall height of the screen frame and subtract

1-3/8". Using that dimension, measure down from the

top edge of the wall bracket and mark the wall for

two screw holes. The holes should be centered

within the frame and 6" apart. Refer to Figure 3.

3. Attach the small wall bracket to the wall. Refer to

Figure 4 for proper orientation. Do not tighten the

screws completely. The bracket should slide up and

down easily.

4. Unroll the screen on a clean surface. Do not use

newspaper. The viewing side is rolled to the inside of

the roll. Place the frame over the screen surface, and

while lifting the frame with one hand, snap the

screen surface onto the frame with the other hand

while maintaining a steady pull on the surface.

5. Hang the screen on the brackets by hooking the

bottom of the frame onto the lower wall bracket and

lift up until you can hook the top of the frame on the

top bracket. Push down on the frame to seat it on the

brackets. Refer to Figure 4.

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

There are four methods of installation based on the size

of the screen and type of viewing surface. Measure the

width of the viewing area of your screen and refer to the

appropriate method of installation below. The wall

bracket diagram shows the type and quantity of

bracket(s) supplied based on the size of the screen.

Method 1: Screens 80" and smaller in viewing width.

Method 2: Screens over 80" up to 96" in viewing width.

Method 3: Screens over 96" in viewing width.

Method 4: Any size screen with High Power®viewing

surface.

INSTALLATION

FIGURE 2

SMALL WALL BRACKET

1-PIECE

FIGURE 3

FIGURE 4

LARGE WALL

BRACKET

1-PIECE

LARGE WALL BRACKET

OVERALL HEIGHT LESS 1-3/8"

OVERALL

HEIGHT

LIFT

WALL

METHOD 1 (SCREENS 80" AND SMALLER IN

VIEWING WIDTH)

1. Secure the wall bracket to wall studs at the desired

height. Make sure the bracket is level. The top of the

frame will be 1/8" above the top of the wall bracket

when mounted. You will need at least 5/8" clearance

above the bracket to hang the screen. Figures 2, 3, and

4 show the proper orientation for the supplied wall

brackets.

SMALL WALL

BRACKET

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Da-Mat
Kleur van het product:	Black, White
Gewicht:	12700 g
Oorspronkelijke beeldverhouding:	4:3
Montagewijze:	Muur
Zichtbare schermhoogte (h):	1460 mm
Zichtbare schermbreedte (b):	1090 mm
Diagonaal:	72 "
Totale grootte van het scherm (hoogte x breedte):	109 x 146 cm
Formaat:	Video