Da-Lite Boardroom Electrol Handleiding

Da-Lite Projectiescherm Boardroom Electrol

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Boardroom Electrol (12 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/12

INSTRUCTION BOOK FOR

Boardroom Electrol®

Important Safety Instructions

When using your video equipment, basic safety precautions

should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating

at least equal to that of the appliance should be used. Cords

rated for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric

shock when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by

the manufacturer may cause a risk of ire, electric shock, or

injury to persons.

6. Failure to provide adequate structural strength for this

component can result in serious personal injury or damage to

equipment! It is the installer’s responsibility to make sure the

structure to which this component is attached can support the

weight of all equipment. Reinforce the structure as required

before installing the component.

7. Use this projection screen only for its intended use as described

in these instructions. Do not use attachments not recommended

by the manufacturer.

Save These Instructions

Pre-Installation

Installation

1. Carefully unpack screen and remove outer

wrapping from case.

2. Make sure to recheck measurement of screen

location before installation.

3. Remove center support brackets (on 8' and wider

screens only), reverse brackets and reinstall lush with

the top of the box.

NOTE: Unit is not to be installed in air handling space.

1. Install screen by raising unit into position between joists at

one end only. Install one lag screw or appropriate fastener in

each mounting bracket. Secure opposite end. Secure center

support brackets. Install suicient fasteners in each bracket

for secure installation.

2. Make sure unit is level and plumb.

CAUTION! Do not secure access door or seal in unit

until screen has been secured in position and properly

tested for satisfactory operation. Do not it unit so tightly

that the screen surface drop door binds. Door drops by

gravity only.

ATTENTION! Ne ixez pas la trappe d'accès ou ne scellez

pas l'unité jusqu'à ce qu'il ait été correctement mis en

place et qu'il fonctionne convenablement. Ne serrez pas

l'unité au point que la surface de la trappe d'accès de

l'écran soit bloquée. La trappe tombe uniquement à cause

de la gravité.

3. If you are going to cover screen door with paneling or other

materials, allow access (suitable holes or plug) to slat hook

screws (4) when servicing (Fig. 1).

Figure 1

Slat Hook

Screws

Tape Strips

Original Instructions

Disclaimer

Milestone and its ailiated corporations and subsidiaries

(collectively "Milestone"), intend to make this manual accurate

and complete. However, Milestone makes no claim that the

information contained herein covers all details, conditions or

variations, nor does it provide for every possible contingency in

connection with the installation or use of this subject to change

without notice or obligation of any kind. Milestone makes no

representation of warranty, expressed or implied, regarding the

information contained herein. Milestone assumes no

responsibility for accuracy, completeness or suiciency of the

information contained in this document.

Da-Lite® is a registered trademark of Milestone AV Technologies.

4. Open access door by removing access door screws (Fig. 2).

5. Remove junction box cover plate.

6. Remove switch assembly (boxed, located at pin end of fabric).

CAUTION! Do not cut wrapping paper or tape with knife

or any sharp tool. Remove by hand.

ATTENTION! Ne coupez pas le ruban adhésif sur la toile

avec un couteau ou un outil tranchant. Retirez à la main.

7. Pull orange string to remove wrapping paper.

8. Install electrical hook up that applies to your unit. Standard

installation is for a single 120VAC or 240VAC wall switch to

control the screen. Optional Control units may have been

ordered. Refer to additional instructions for the external VPI,

external low voltage control and SCB100. Refer to the

appropriate wiring diagram for your screen.

NOTE: Screen has been internally wired at DALITE. Wiring

designated “external” is completed by installer conforming to

local and national codes.

9. Lower picture surface approximately 4"-6" so that the slat will

rest on top of the slat hooks. Guide slat past hooks by gently

pulling fabric forward (Fig. 3). Do not bend hooks.

10. Test installation by carefully running picture surface up and

down 23 times. Be prepared to stop screen. Standard Duty

Cycle: 1 MIN. ON / 3 MIN. OFF.

11. Run the picture surface upward. The surface door will

automatically close when the picture surface rolls into the

case. The ends of the slat will catch the two hooks on the

surface door and pull the door closed. When the door closes,

a limit switch is tripped and the motor shuts of.

CAUTION! Excessive continuous operation may cause

overheating.

ATTENTION! Le fonctionnement continu et excessif peut

provoquer une surchaufe.

12. Run picture surface downward until picture surface

door fully opens.

13. Install junction box cover plate.

14. Close access door and reinstall screws at each end

of access door.

CAUTION! Do not attempt to restore a lost wrap by

adjusting limit switches. Allow one-eighth of an inch (1/8")

clearance around surface door. Make sure door does not

bind. Check hinges. Paint or tile cement will interfere with

free operation. Gravity drops door.

ATTENTION! N'essayez pas de réintégrer un tour de toile

en réglant les interrupteurs de limite! Laissez un espace

0,30 cm (1/8 po) autour de la trappe. Vériiez que la

trappe n'est pas entravée. Vériiez les gonds. La peinture

ou le ciment à tuile nuira au bon fonctionnement. La

gravité fait tomber la trappe.

15. Complete installation by painting and inishing to suit

your needs. Finish to allow access door to be removed

if necessary.

Installation (continued)

Figure 2

Figure 3

Fabric Door

Access

Door

Screw

Access Door

Mounting Brackets

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Boardroom Electrol
Kleur van het product:	Wit
Gewicht:	- g
Oorspronkelijke beeldverhouding:	1:1
Kijkhoek:	60 °
Zichtbare schermhoogte (h):	3050 mm
Zichtbare schermbreedte (b):	3050 mm
Diagonaal:	- "
Totale grootte van het scherm (hoogte x breedte):	- cm
Formaat:	Vierkant
Schermgain:	1
Case L1:	3390 mm