Da-Lite Ascender Electrol 84766E Handleiding

Da-Lite Projectiescherm Ascender Electrol 84766E

Lees hieronder de 📖 handleiding in het Nederlandse voor Da-Lite Ascender Electrol 84766E (8 pagina's) in de categorie Projectiescherm. Deze handleiding was nuttig voor 64 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

INSTRUCTION BOOK FOR

Ascender Electrol

ATTENTION! Les ressorts des bras de l'écran sont fortement

tendus.

Ne vous placez pas devant l'écran pendant son

fonctionnement.

Ne vous asseyez pas, ne vous tenez pas debout, ou ne placez

aucun objet sur la trappe du caisson de l'écran.

Ne couvrez pas la trappe du caisson de l'écran avec un

revêtement en bois, de la moquette, des stratiiés

supplémentaires, etc. Tout poids ajouté à la trappe du

caisson de l'écran pourrait entraîner, avec le temps, le

dysfonctionnement de l'écran.

La trappe du caisson active un interrupteur de sécurité situé

à l'intérieur du caisson de l'écran. Si vous essayez d'élever

l'écran alors que quelque chose tient la trappe fermée, le

moteur rétractera l'écran. La trappe doit être complètement

fermée pour activer cet interrupteur. Vériiez que la trappe

n'est pas entrouverte.

Pre-Installation

Important Safety Instructions

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Position the cord so that it will not be tripped over, pulled, or

contact hot surfaces.

3. If an extension cord is necessary, a cord with a current rating at

least equal to that of the appliance should be used. Cords rated

for less amperage than the appliance may overheat.

4. To reduce the risk of electric shock, do not disassemble this

appliance. Contact an authorized service dealer when repair

work is required. Incorrect reassembly can cause electric shock

when the appliance is used subsequently.

5. The use of an accessory attachment not recommended by the

manufacturer may cause a risk of ire, electric shock, or injury to

persons.

Save These Instructions

1. The Ascender screen must be installed on a lat, level surface.

2. Remove the white shipping braces (mounted at the end of the arms to the back of the case).

3. Refer to the chart below for minimum overhead clearance required to raise the screen.

4. Allow 12" clearance from back of screen housing to allow arms to extend properly.

5. Remove packing paper from fabric roller. DO NOT use a knife or sharp object to remove the paper.

Screen Operation

CAUTION!

The arms of the screen are under high spring tension.

Do not stand over the screen while it is operating.

Do not sit, stand, or put anything on the screen case door.

Do not apply anything (wood inish, carpet, additional

laminate, etc.) to the screen case door. Any weight added to

the screen case door may cause the screen to malfunction

over time.

The case door activates a safety switch inside the screen

case. If you attempt to raise the screen while something is

holding the door shut, the motor will reverse and retract the

screen. The door must be fully closed to activate this switch.

Be sure there is nothing holding the door ajar.

Diagonal Extended Height

100" 94"

120" 104"

150" 121"

180" 139"

200" 149"

Diagonal Extended Height

106" 86"

119" 92"

133" 99"

159" 112"

4:3 Video Format 16:9 HDTVFormat

CAUTION! Excessive continuous operation may cause

overheating. If this happens, the motor will shut of until it

cools to normal operating temperature. Standard duty cycle

is 1 min. on / 15 min. of.

ATTENTION! Le fonctionnement continu et excessif peut

provoquer une surchaufe et l'arrêt du moteur. Si cela se

produit, les moteurs s'arrêteront jusqu'à qu'ils se soient

refroidis à la température normale de fonctionnement. Le

cycle de fonctionnement normal est de 1 min. en marche / 15

min. à l'arrêt.

Screen Operation (continued)

Ascender Electrol® Installation

1. For installations where the Ascender will be set on the loor, the

box must be secured to loor in at least six places (recommended

hardware is #12 x 2" L wood screws)(Figure 1).

Screw Box Into Floor Stud

Floor

Box Frame Support

Figure 1 Figure 2

2. For installations where the Ascender will be recessed into the

loor, the box must be secured in at least six places

(recommended hardware is #12 x 2" L wood screws)(Figure2).

1. The Ascender screen can be operated by the included wall

switch or by optional remote controls (IR or RF).

2. To raise the screen, simply push and release the wall switch. The

screen will stop at its preset position. If you push the switch a

second time while it is rising, the screen will stop. By pushing the

switch a third time the screen will retract and close.

3. To lower the screen from the fully up position, press and release

the wall switch and the screen will retract and close.

4. Test the screen by running it up and down a few times. Be

prepared to stop the screen if needed.

Product specificaties

Merk:	Da-Lite
Categorie:	Projectiescherm
Model:	Ascender Electrol 84766E
Oorspronkelijke beeldverhouding:	16:9
Montagewijze:	Vloer
Frame type:	Vouwbaar frame
Aantal per verpakking:	1 stuk(s)
Ingangsspanning:	220 V
Frequentie:	50 Hz
Zichtbare schermhoogte (h):	1470 mm
Zichtbare schermbreedte (b):	2640 mm
Diagonaal:	119 "
Type aandrijving:	Gemotoriseerd
Formaat:	HDTV
Schermgain:	1
Schermoppervlak:	Mat wit
Spanscherm:	Nee