D-Link DIS-100G-5SW Handleiding

D-Link Schakelaar DIS-100G-5SW

Lees hieronder de 📖 handleiding in het Nederlandse voor D-Link DIS-100G-5SW (8 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 36 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

DIS-100E Series Unmanaged

Industrial Fast Ethernet Switch

Quick Installation Guide

O verview

The -DIS 100E Series nmanaged Industrial U Fast Ethernet

Switch solutions are designed for supporting standard

industrial applications without complex setup, allowing for

a - - truly plug and play network.

If the equipment is used in a manner not specified by the

manufacturer, the protection provided by the equipment

may be impaired.

Package Checklist

Please verify that the box contains the following items:

Item Quantity

Unmanaged switch 1

Wall-mount plates 2

DIN r 1 ail clip

M4 Screws

(for the wall mount plates &

DIN clip)

DC power terminal block 1

RJ-45/SFP protective cap 2-4

Quick Installation Guide 1

Safety I nstructions

When a connector is removed during installation, testing,

or servicing, or when an energized fiber is broken, a risk of

ocular exposure to optical energy that may be potentially

hazardous occurs, depending on the laser output power.

The primary hazards of exposure to laser radiation from an

optical-fiber communication system are:

 Damage to the eye by accidental exposure to a beam

emitted by a laser source.

 Damage to the eye from viewing a connector attached

to a broken fiber or an energized fiber.

Documentation Conventions

The following conventions are used in this quick installation

guide to emphasize information that will be of interest to

the reader.

D — ANGER The described activity or situation might or

will cause personal injury.

WARNING — The described activity or situation might

or will cause equipment damage.

C — AUTION The described activity or situation might or

will cause service interruption.

N — OTE The information supplements the text or

highlights important points.

Di mension Illustration (unit: mm)

5- Port Model

8- Port Model

DIN Rail- M ounting

1. Attach the DIN rail kit onto the switch using the bracket

and screws in the accessory kit.

2. Hook the unit over the DIN rail.

3. Push the bottom of the unit towards the DIN rail until it

snaps into place.

Wall M ounting (unit: mm)

1. the Attach wall mounting kit onto the switch using the

mounting plate and s M4 screws in the accessory kit.

5- Port Model

8- l Port Mode

Connecting to Ground

The switch must be properly grounded for optimum system

performance.

5- 8- Port Model Port Model

Connecting to Ethernet Interfaces

(RJ- 45)

Connecting the Ethernet interface via RJ- 45:

 To connect to a PC, use a straight through or a -

cross-over Ethernet cable,

 To connect the switch to an Ethernet device, use UTP

(Unshielded Twisted Pair) or STP (Shielded Twisted

Pair) Ethernet cables.

The pin assignment of the RJ-45 connector is shown in the

following figure and table.

Pin Assignment

1,2 - T/Rx+,T/Rx

3,6 R/T R/Tx- x+,

Ver. 1.0 )0(WW 2018/ / - 06 06 GP801010X 000

Connecting to Fiber Interfaces ( ) SFP

Please prepare LC connectors or SC connectors (with the

the use of an optional SC se adapters -to-LC adapter). The

are available with multimode, single mode, long haul (for -

connections up to 120+ km) or in the form of

special-application transceivers.

For each fiber port there is a transmit (TX) and receive (RX)

signal. Please make sure that the transmit (TX) port of the

switch connects to the receive (RX) port of the other device,

and the receive (RX) port of the switch connects to the

transmit (TX) port of the other device when making your

fiber optic connections.

DANGER: Never attempt to view optical connectors

that might be emitting laser energy.

Do not power up the laser product without

connecting the laser to the optical fiber and

putting the cover in position, as laser

outputs will emit infrared laser light at this

point.

Connecting the Power

The switch can be powered two powerusing supplies

(input range 12V Insert the positive and negative – . 58V)

wires into V+ and Vthe - contacts on the terminal block and

tighten the wire-clamp screws to prevent the wires from

being loosened.

N : OTE The DC power should be connected to a

properly-fused power supply.

Connecting the Alarm Relay

The alarm relay output contacts are in the middle of the DC

terminal block connector as shown in the following . figure

By inserting the wires and set the DIP switch of the Port ting

Alarm to “ ”ON , the relay output alarm will detect any port

failures, and form a short circuit.

The alarm re Normal Openla “y out is ”.

DIP Switch Setting

Pin No# 5-Status Port Model

Pin 1

ON E nable the power alarm.

OFF D isable the power alarm.

Pin 2

ON E b . nable roadcast storm rate limiting

OFF D b . isable roadcast storm rate limiting

Pin No# 8- t Status Por Model

Pin 1

ON E b . nable roadcast storm rate limiting

OFF D b . isable roadcast storm rate limiting

Pin 2

ON E nable the power alarm.

OFF D isable the power alarm.

LED STATUS INDICATIONS

LED Name

Status

Condition

Solid

green

P1 power line has power.

Off

P1 power is disconnected or

is not being powered.

Solid

green

P2 power line has power.

Off

P2 power disconnectedis or

is not being powered.

Alarm

Solid red

Power failure alarm

triggered.

Off

No power failure alarm.

Copper 1 to

N port

Link/Act

Solid

g reen

Ethernet link up but no traffic

is detected.

Blinking

g reen

Ethernet link up and there is

traffic detected.

Off

Ethernet link down.

Copper 1 to

N port

Speed

Solid

y ellow

A 100Mbps connection is

detected.

Off

No link, or a10Mbps

connection is detected.

SFP 1 to N

port

(N=0,1,2)

Link/Act

Solid

g reen

SFP p . ort link up

Off

SFP . link down

Additional Information

You can refer to the user manual or visit

http://support.dlink.com/ for more support.

Online Support

If there are any issues that are not in the user manual,

please visit http://support.dlink.com/ which will direct you to

your appropriate local D-Link support website.

Warranty Information

Visit http://warranty.dlink.com/ to view the D-Link Warranty

information.

Product specificaties

Merk:	D-Link
Categorie:	Schakelaar
Model:	DIS-100G-5SW
Kleur van het product:	Zwart
Gewicht:	295 g
Breedte:	112.2 mm
Diepte:	29.1 mm
Hoogte:	89.4 mm
Gewicht verpakking:	500 g
Breedte verpakking:	140 mm
Diepte verpakking:	178 mm
Hoogte verpakking:	83 mm
LED-indicatoren:	LAN, Power
Vermogensverbruik (max):	3.57 W
DC voltage input:	12 - 58 V
Certificering:	IEC60068-2-6; IEC60068-2-27; IEC60068-2-32; UL 60950-1, CE, FCC, RoHS, WEEE
Netwerkstandaard:	IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Temperatuur bij opslag:	-40 - 85 °C
Stroomspanning bescherming:	Over current, Reverse polarity
Luchtvochtigheid bij opslag:	0 - 95 procent
Elektromagnetische compatibiliteit:	FCC 15, EN 61000-6-2, EN 61000-6-4, EN 61000-4-2, -3, -4, -5, -6 (3)
Ophangsysteem voor aan de muur:	Ja
Auto MDI/MDI-X:	Ja
Power over Ethernet (PoE):	Nee
Nettogewicht transportverpakking:	5000 g
Switchingcapaciteit:	10 Gbit/s
MAC-adrestabel:	2000 entries
10G support:	Nee
Datastroombeheer:	Ja
Switch type:	Unmanaged
Multicast-ondersteuning:	Ja
Aantal basis-switching RJ-45 Ethernet-poorten:	4
Switch-laag:	L2
Type basis-switching RJ-45 Ethernet-poorten:	Gigabit Ethernet (10/100/1000)
Aantal moduleslots SPF:	1
Jumbo Frames ondersteuning:	Ja
Full duplex:	Ja
Warmtedissipatie:	12.18 BTU/h
(Binnenste) verzendverpakking gewicht:	5640 g
Auto-negotiation:	Ja
Stroomverbruik (typisch):	2.74 W
Bedrijfstemperatuur (T-T):	-40 - 75 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 95 procent
Code geharmoniseerd systeem (HS):	85176990
Pallet brutobreedte:	1100 mm
Pallet brutolengte:	1200 mm
(Binnenste) verzendverpakking hoogte:	205 mm
(Binnenste) verzendverpakking breedte:	305 mm
(Binnenste) verzendverpakking lengte:	440 mm
Producten per (binnenste) verzendverpakking:	10 stuk(s)
Verzending snelheid:	7.44 Mpps
Jumbo frames:	9000
DIN rail bevestiging:	Ja
Broadcast stormbeheer:	Ja
Store-and-forward:	Ja
Vezel-optische connector:	LC
Pallet brutogewicht (lucht):	220040 g
Aantal dozen per pallet (lucht):	36 stuk(s)
Aantal per pallet (lucht):	360 stuk(s)
Pallethoogte (lucht):	1365 mm
Pallet brutogewicht (zee):	321560 g
Aantal dozen per pallet (zee):	54 stuk(s)
Producten per pallet (zee):	540 stuk(s)
Pallethoogte (zee):	1980 mm
Traffic shaping:	Ja