CyberPower CPS160PBU Handleiding

CyberPower Accu CPS160PBU

Lees hieronder de 📖 handleiding in het Nederlandse voor CyberPower CPS160PBU (1 pagina's) in de categorie Accu. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
AC Mobile Power Inverter
CPS160PBU User Guide
Specifications
Troubleshooting
Fuse Replacement
Important Safety Information
Package Contents
Product Features
AC Mobile Power Inverter
• User Guide
1. Unplug the inverter from the DC power outlet.
2. Replace the 15 amp fuse.
3. Reassemble unit by reversing the instructions above.
Input Voltage 10.5 to 15.5 volts
Output Peak Power 160 Watts
Output Continuous Power 100 Watts
Output Voltage 120 Volts / USB 5 Volts
Output Frequency 60 Hz
Output Waveform Simulated Sine Wave
Protection Features Low Voltage, Overheat,
Overload, Short Circuit
Problem
No AC output power Poor contact with DC power
outlet.
Automotive electrical system
requires ignition to be on.
Car's DC power outlet fuse is
blown.
Over-heating.
Vehicle's battery voltage is
below 10.5 volts.
Vehicle's battery input voltage
is higher than 15.5 volts.
Inverter is overloaded.
Ensure the inverter is securely plugged
into vehicle's DC power outlet. Replace
the DC power outlet if necessary.
Turn the vehicle ignition to the
"Accessory" position.
Check the vehicle fuse panel and
replace the damaged fuse.
Allow inverter to cool. Ensure that there
is adequate ventilation around the unit
and load does not exceed the unit's
Continuous Power rating (see
specifications).
Unplug the inverter and start the vehicle
to charge the battery.
Check your vehicle's user guide for
troubleshooting.
Ensure load does not exceed the unit's
Continuous Power rating (see
specifications).
Suggested SolutionsPossible Cause
Before installing and using the CyberPower CPS160PBU Mobile Power
Inverter please read and follow these safety instructions:
• Moderate Temperature - Ambient air temperature should be between
32oF - 104oF (0oC - 40oC). Keep the inverter out of direct sunlight.
• Free Air Flow - Keep the inverter's ventilation slots unobstructed to ensure
air flow to the unit. Do not place any items on or over the inverter during
operation. The unit will shut down if it overheats.
Storage Tips
• Proper storage temperature range is 32
oF - 86oF (0oC - 30oC)
• Store and use the inverter in a cool and dry environment.
Avoid exposing the inverter to heating elements, direct sunlight, or high
humidity.
Operating and Storage Tips
Operating Tips
The inverter should only be operated under the following conditions:
• Dry - Do not allow water or other liquids to come into contact with the
inverter.
• Do not operate the CPS160PBU near flammable materials, fumes, or
gases.
Always use the inverter where there is adequate ventilation. Do not
obstruct the ventilation slots.
• Never immerse the unit in water.
• Proper cooling is essential when operating the inverter. Refrain from
placing the inverter near the vehicle's heat vent, or in direct sunlight.
Always turn the inverter off when not in use by removing it from the DC
accessory socket.
• Check the warning labels on battery chargers or adapters before
connecting them to the inverter. Do not connect battery chargers or
adapters with warnings about using with inverters.
CyberPower Systems (USA), Inc.
4241 12th Av enue Eas t, Suite 400, Shak opee, MN 55379
TEL: (952) 403-9500 Toll-Free: (877) 297-6937
FAX: (952) 403-0009 E-mail: sal es@cps ww.com
CPSww.com
C 2014 CyberPower Systems, Inc.
All rights reserved. Reproduction in whole or in part without permission is prohibited.
K01-0000345-00
Limited Warranty
Product Registration
Technical Support
Legal notices (FCC Part 15)
CyberPower warrants this CPS160PBU (the "Inverter") to be free from material and
manufacturing defects for two years. If a defect results in product failure during its
normal use, CyberPower’s sole responsibility is to repair or replace (at its sole option)
the Inverter.
The foregoing Limited Warranty is the consumer’s sole and exclusive remedy and
excludes any incidental or consequential damages. Some States do not allow the
exclusion or limitation of incidental and consequential damages, so certain of the
above limitations or exclusions may not apply to you (the Consumer). This limited
warranty gives the Consumer specific legal rights and the Consumer may have other
rights, which vary from State to State.
To make a Limited Warranty claim:
1. Pack and ship the Inverter to CyberPower at 4241 12th Avenue East, Suite 400,
Shakopee, MN 55379.
2. Clearly indicate on the outside of the packaging that this is a “WARRANTY
RETURN”
3. Clearly include your name and address (a) on the outside packaging and (b) on a
sheet of paper enclosed in the box with the Inverter that is being returned.
4. You MUST prepay all shipping costs and you are responsible for packaging and
shipment.
CAUTION: Any changes or modifications not expressly approved by the guarantee
of this device could void the user’s authority to operate the equipment.
Thank you for purchasing a CyberPower product. Prompt product registration entitles
coverage under the Limited Warranty and Connected Equipment Guarantee, and also
allows the opportunity to be notified of product enhancements, upgrades, and other
announcements.
Registration is quick and easy at www.cpsww.com/register
Feel free to contact our Tech Support department with installation, troubleshooting, or
general product questions.
CyberPower Technical Support
Phone: 1-877-297-6937
Email: tech@cpsww.com
Web: www.CPSww.com
Address: 4241 12th Ave. E., STE 400, Shakopee, MN 55379
Hours of Operation: Monday – Friday, 8:00am – 5:00pm (CST)
This equipment has been tested and found to comply with the limits for a Class B Digital Device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures: (1) Reorient or relocate the receiving antenna. (2) Increase the separation between the
equipment and receiver. (3) Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected. (4) Consult the dealer or an experienced radio/TV technician for
help. Any special accessories needed for compliance must be specified in the instruction.
CAUTION: A shielded-type power cord is required in order to meet FCC emission limits and
also to prevent interference to the nearby radio and television reception. It is essential that only the
supplied power cord be used. Use only shielded cables to connect I/O devices to this equipment.
Spring
Ring
Contact Pin
Contact Retainer
15A Fuse
Power plug
1. 12V power plug
2. USB charging port
3. Cooling Fan
4. 120V AC outlet
1
2
3
4


Product specificaties

Merk: CyberPower
Categorie: Accu
Model: CPS160PBU

Heb je hulp nodig?

Als je hulp nodig hebt met CyberPower CPS160PBU stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Accu CyberPower

Handleiding Accu

Nieuwste handleidingen voor Accu