CTA Digital ADD-MEDARM Handleiding

CTA Digital Flat panel steun ADD-MEDARM

Lees hieronder de 📖 handleiding in het Nederlandse voor CTA Digital ADD-MEDARM (2 pagina's) in de categorie Flat panel steun. Deze handleiding was nuttig voor 3 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Anti-Microbial

Medical VESA Arm Wall Mount

ADD-MEDARM

INSTRUCTION - MANUAL

CONTENTS:

INSTALLATION:

888-733-4448

1A. Place the canopy (component A) of the medical arm to the desired

location on the wall. Using a screwdriver (not included), and compo-

nents P, Q, and R - set up the canopy to the wall until securely

tightened. Place endcap (component J) on, after everything has been

securely tightened for a clean finish.

1. Setting up Mounting Canopy to Wall

ABC

x1 x1 x1

M N

x1x1 x2

O P

QRST

x2 x1 x1

**Screwdriver shown for

example and NOT included

2. Assembling the Arm to the Canopy

2A. Insert medical arm (component B) into the

wall canopy with the plastic washer (component

F) as shown.

2B. Using the combination of components E, D,

H, G and I, assemble the arm and rotate in

screw (component I) with provided tool

(component M) until securely tightened.

888-733-4448

3. Assembling the VESA Plate to a VESA Compatible Item

**Screwdriver shown for

example and NOT included

3A. Align the VESA holes of the VESA plate to the

VESA compatible item as shown. Only VESA hole

configurations are 75x75mm or 100x100mm are

possible.

3B. Using a screwdriver (not included), rotate in (4)

screws (component K) from behind of the VESA

plate (component C - shown to the left) until

securely tightened.

**Monitor shown for

example and NOT included

4. Inserting VESA Plate attatched to VESA Compatible Item into the arm

4A. Take your VESA Plate (component C) attached

with the VESA compatible item and insert and

connect the female to male components as shown

to the right.

4B. Using the provided allen key tool (component

N), tighten the pieces together at the integral piece

shown to the right until securely fastened.

5. Setting up Cable Routing / Cable Management

(TOP VIEW) (FRONT ANGLE VIEW)

5A. Locate the holes in the medical arm to understand the pathing a little bit from

right next to VESA plate (component C), all the way to the canopy (component A)

5B. Plug one end of the cable into your device and fish the wire underneath the

arms as shown while putting on the arm caps (component T and S) by rotating in

screws (component L) until securely fastened. Plug other end of cable into outlet or

desired power source as required.

**Monitor shown for

example and NOT included

**Monitor shown for

example and NOT included

***Loading: Approximately 1-3 KG

Adjusting Tilt Angles

Using the provided tool (component M), tighten and

loosen the joint behind the VESA plate (component C)

to adjust different angles and also set it in place once

desired angles has been found as shown

Product specificaties

Merk:	CTA Digital
Categorie:	Flat panel steun
Model:	ADD-MEDARM
Kleur van het product:	Wit
Gewicht:	1615 g
Breedte:	114.3 mm
Hoogte:	482.6 mm
Gebruikershandleiding:	Ja
Materiaal behuizing:	Metaal
Montagewijze:	Muur
Markt positionering:	Medisch
Paneelmontage-interface:	75 x 75, 100 x 100 mm
Aantal per verpakking:	1 stuk(s)
Inclusief schroeven:	Ja
Aantal displays ondersteund:	1
Type product:	Flatscreen bevestigingsarm
Verstelbare diepte:	Ja