CRUX RVCVW-73L Handleiding


Lees hieronder de đź“– handleiding in het Nederlandse voor CRUX RVCVW-73L (3 pagina's) in de categorie Achteruitrijcamera. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
RVCVW-73
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3 RNS315 & RNS510 Navigation System
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.121819
1 of 3
- Automacally switches to Rear-view when car is in Reverse mode.
- Aî…Śermarket Rear-view Camera included.
- OBD coder for single acvaon included.
- Plug & Play Installaon.
PRODUCT FEATURES:
PARTS INCLUDED:
RVCVW-73 Module RVCVW-73 Harness OBD II Coder
Power Down Circuit CUL-03 Camera
GROUND
RED Wire Tape O
(Not Used)
FACTORY
RADIO
12-PIN
(male plug)
26-PIN
(female plug)
NAV
MUTE
SETUP
BAND
MEDIA
PHONE
i
VIDEO
CONNECTION
POWER DOWN
CIRCUIT
RED / R E TR R PUTEV RSE IGGE IN
YELLOW / 12V CONSTANT
BLA CK / G DROUN
INTERFACE
RED / 12V POWER
BLACK / GROUND
FR OM REVE E IGHTRS L
THIN RED
WIRE
LIP MOUNT
CAMERA
INSTALLATION DIAGRAM:
SPECIAL NOTE:
In the event this unit is to be returned for any reason, the customer must “decode” the radio before
doing so to receive a replacement or refund. See instructions on page 2 on how to decode the radio.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.121819
2 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCVW-73
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3/RNS315/RNS510 Navigation System
INSTALLATION INSTRUCTIONS:
CODING THE RADIO FOR A BACKUP CAMERA
1. Locate the vehicle’s OBD II port usually located under the steering column.
2. Enter the vehicle and CLOSE ALL DOORS.
3. Turn the key to the ON posion.
4. Plug in the OBD coder from the RVCVW-73 kit to the ODB II port.
5. Wait for the OBD coder to î„®nish coding the radio and give a solid GREEN LED. (See chart below)
6. The radio may ash a few me during this process. It can take around 5 seconds to complete the
coding process. If an error occurs, retry the coding procedure.
7. Aî…Śer the coding is complete, disconnet the OBD coder and store in a safe place. This OBD coder is
VIN speciî„®c and will only work on this vehicle.
In order for the vehicle to recognize the camera and engage it when in reverse gear, the vehicle must be
coded. Use the ODB II coder included in the RVCVW-73 kit.
Reading the LED color paern:
Flashing LED Coding Vehicle
Solid Green LED Acvated
Solid Red LED Deacvated
Solid Red & Green LED Error
INTERFACE
GREEN LED
RED LED
8-PIN
(male plug) LED
(indicator)
OBD CODER
DECODING THE RADIO
To decode the radio, repeat the steps above.
INSTALLING THE CAMERA
1. Remove the trunk lid panel.
2. Use the hole saw included in the kit to drill a hole on the lip of the trunk handle area.
3. Fish the camera cable through the hole and connect to the extension cable.
4. Connect the black wire of the camera to chassis ground. The red wire will not be used. Insulate it with tape.
5. Run the extension cable towards the radio.
6. Make the video and power connecons to the RVCVW-73 harness.
7. Connect the power down circuit (below) then test the camera for funconality before reinstalling the radio.
Crux Interfacing Solutions • 21541 Nordhoff St., Unit C, Chatsworth, CA 91311
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.121819
3 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCVW-73
Rear View Integration Interface for Select
Volkswagen Vehicles with MFD3/RNS315/RNS510 Navigation System
VEHICLE APPLICATIONS:
MFD3 RNS315 Navigaon Radios
2011 – 2014 CC
2011 – 2014 Golf
2011 – 2014 GTI
2011 – 2014 Jea
2011 – 2014 Jea SportWagen
2012 – 2014 Passat*
2011 – 2014 Tiguan
USING THE POWER DOWN CIRCUIT
The power down circuit is designed to extend the life of the camera. NOTE: Green wire is only used to power the
camera and module.
1. Tap the GREEN wire to 2 Red wires, one coming from the camera cable and one from the module.
2. Locate the reverse light trigger wire in the vehicle and connect it to the RED wire. This will trigger the 12V input.
3. Connect the YELLOW wire to any available 12V constant source in the car.
4. Connect the BLACK wire to a good chassis ground source.
MFD3 RNS510 Navigaon Radios**
2007 – 2009 Eos
2007 – 2009 Golf
2007 – 2009 Passat
2008 – 2009 Tiguan
2008 – 2010 Touareg
VOLKSWAGEN
IMPORTANT NOTES:
*On the 2012 Passat radio (RNS315), the rear-view camera will start to funcon aer the car goes to sleep/power down mode. Aer
the coding process, turn key oî„« and remove key. Open and close doors then lock the car. Wait for 3 minutes. Start the car and put
the gear in reverse and conî„®rm that the camera image shows on the screen.
**Certain U.S. version RNS-510 Radios (late 2009-up) may not have camera input capability. Please verify feature prior to purchase.
MFD3 / RNS315 Radio RNS510 Radio


Product specificaties

Merk: CRUX
Categorie: Achteruitrijcamera
Model: RVCVW-73L

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX RVCVW-73L stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Achteruitrijcamera CRUX

Handleiding Achteruitrijcamera

Nieuwste handleidingen voor Achteruitrijcamera