CRUX RVCCH-75DC Handleiding
CRUX
Achteruitrijcamera
RVCCH-75DC
Lees hieronder de đź“– handleiding in het Nederlandse voor CRUX RVCCH-75DC (6 pagina's) in de categorie Achteruitrijcamera. Deze handleiding was nuttig voor 76 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/6
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
1 of 3
• Adds reverse camera input to the Uconnect Touchscreen Radio
• Aermarket tailgate handle camera included
• Automacally switches to Rear-view when car is in Reverse mode
• Plug & Play Installaon
PRODUCT FEATURES:
PARTS INCLUDED:
RVCCH-75DC Module RVCCH-75DC Harness CDR-02 Camera
INSTALLATION DIAGRAM:
WHITE Wire
Parking Guideline
To Radio
OEM Radio
Harness
DP
ON
DIP
SWITCH
LED*
*LED RED = Power ON Status
LED BLUE = Data Bus ON Status
RVC Video
Signal Input
RED Wire Push in Connectors
all the way
Line up Arrows
Regulator
20 Ft. Coax Cable
RED Wire
Tape O
(Not Used)
BLACK
Wire
BLACK
(Ground)
8-Pin Molex Represents Solder Joint
Connect RCAs and secure
with tape all around
WHITE Wire
(Camera Power Output
+12V 250mA)
OR*
*Connect BLACK (ground) wire to chassis ground.
If video noise is present, we recommend connecting the
ground wire to the BLACK ground wire on the RVCCH-75DC harness.
Chassis Ground
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
2 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
DIP SWITCH SETTINGS:
INSTALLATION INSTRUCTIONS:
INSTALLING THE CDR-02 CAMERA AND CABLE
1. Remove the OE tailgate handle.
2. Remove the OE lock cylinder and install in the CDR-02 camera housing.
3. Install the new tailgate handle and run the cables to the radio.
4. Remove the factory radio to gain access to the factory connectors.
5. Route the wires towards the radio and make the power and video connecons. For powering up the camera, use the 12V
OUTPUT (White Wire). (See Wiring Diagram on page 1)
6. Connect the camera ground wire to chassis ground. If video noise is present, we recommend connecng a ground wire
from the camera to the BLACK wire on the RVCCH-75DC T-harness.
7. The CDR-02 has a built-in parking guide lines opon and is defaulted to ON from the factory. To turn OFF the parking guide
lines, cut the thin WHITE wire located on the camera cable 4 feet from the camera. Unplug the barrel connectors on the
cable for 10 seconds. Align the arrows on the barrel connectors and î„®rmly plug them together.
8. Test the camera before re-installing the radio.
CODING THE RADIO FOR A REAR VIEW CAMERA
The radio has to be coded to accept a reverse camera. Please follow the coding procedure below:
1) Turn key o and remove the key from ignion.
2) Open the driver door then close it (make sure all doors, liî…Ś gate and hood are also closed).
3) Look at the module and wait for LEDs to turn oî„« then disconnect the module.
4) Before plugging back the module, turn all DIP switches to ON then OFF.
5) Set DIP switches to the sengs provided above.
6) Reconnect module and wait for the LEDs to turn oî„«.
7) Start engine and the coding operaon is now complete.
8) Put the gear in reverse to test the camera.
DIP SWITCH FUNCTIONS:
DIP 1 = Set to OFF
DIP 2 = Rear View Camera ON / OFF
DIP 3 = Set to OFF
DIP 4 = Set to OFF
DIP 5 = Defaulted to OFF*
DIP 6 = Defaulted to ON*
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
*DIP 5 & 6
If the radio is having turn-on issues, please try the following:
Aempt 1: Set 5 & 6 to ON
Aempt 2: Set 5 to ON and 6 to OFF
Aempt 3: Set 5 to OFF and 6 to ON
1 2 3 4 5 6
ON
Crux Interfacing Solutions • 6860 Canby Ave., Suite 104, Reseda, CA 91335
phone: (818) 609-9299 • fax: (818) 996-8188 • www.cruxinterfacing.com
rev.010319
3 of 3
R
INTERFACING SOLUTIONS
Sightline
Multi View Integration
RVCCH-75DC
Rear View Integration Interface with VIM
for DODGE RAM Trucks
VEHICLE APPLICATIONS:
RAM
2013 - 2017 1500
2013 - 2017 2500
2013 - 2017 3500
NOTES:
1. Not compable with diesel powered trucks.
2. Not compble with RAM trucks with factory installed cargo camera.
COMPATIBLE RADIOS:
8.4” Screen with Separate Knobs 5” Screen with 6 Buons &
Separate Knobs
4.3” Screen with 6 Buons &
2 Knobs
4.3” Screen with 4 Buons & 2 Knobs
Not compable radio
Product specificaties
Merk: | CRUX |
Categorie: | Achteruitrijcamera |
Model: | RVCCH-75DC |
Heb je hulp nodig?
Als je hulp nodig hebt met CRUX RVCCH-75DC stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Achteruitrijcamera CRUX
17 November 2024
17 November 2024
17 November 2024
17 November 2024
20 Juni 2023
18 Juni 2023
18 Juni 2023
16 Juni 2023
16 Juni 2023
14 Juni 2023
Handleiding Achteruitrijcamera
- Achteruitrijcamera AEG
- Achteruitrijcamera Garmin
- Achteruitrijcamera Kenwood
- Achteruitrijcamera Pioneer
- Achteruitrijcamera Alpine
- Achteruitrijcamera Dometic
- Achteruitrijcamera Elro
- Achteruitrijcamera Hikvision
- Achteruitrijcamera Luis
- Achteruitrijcamera Maginon
- Achteruitrijcamera Marquant
- Achteruitrijcamera Pro-User
- Achteruitrijcamera Pyle
- Achteruitrijcamera Trebs
- Achteruitrijcamera VDO Dayton
- Achteruitrijcamera Waeco
- Achteruitrijcamera Clarion
- Achteruitrijcamera Conrad
- Achteruitrijcamera Tracer
- Achteruitrijcamera Furrion
- Achteruitrijcamera Valueline
- Achteruitrijcamera Boyo
- Achteruitrijcamera Camos
- Achteruitrijcamera AutoXtreme
Nieuwste handleidingen voor Achteruitrijcamera
5 December 2024
25 November 2024
15 November 2024
6 September 2024
6 September 2024
6 September 2024
6 September 2024
8 Augustus 2024
6 Augustus 2024
4 Mei 2024