CRUX RVCFD-79A Handleiding


Lees hieronder de πŸ“– handleiding in het Nederlandse voor CRUX RVCFD-79A (3 pagina's) in de categorie Achteruitrijcamera. Deze handleiding was nuttig voor 47 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/3
- Automatically switches to Rear-view when car is in Reverse mode.
- Plug and Play Installation.
- Ford 4 Inch FULL COLOR Screen
1. Vehicles with Manual Transmission or Diesel Engines are not compatible.
RVCFD-79A MODULE
RVCFD-79A HARNESS
Blue ON = Valid CAN / Normal operation mode
Blue OFF = Sleep mode
Blue Blinking = CAN BUS validation
Red Blinking Fast = Programming in progress
Red ON = RVC programming successful
Red OFF = RVC coding has been completely removed
Red Blinking Slow = CAN Communication error / Access denied
Red blinking Medium = Invalid license
rev.082718
1 / 3
Please note that the display removal procedure may vary and subject to change.
1. Remove the trim below the radio bezel to
expose the 2 screws.
2. Carefully pop off the radio bezel making note
that it is held by 2 clips as shown on the
illustration above.
3. Remove the 4 screws holding the display screen.
4. Disconnect the factory 12 pin connector from behind the display screen and plug into the female
12 pin connector of the RVCFD-79A T-harness.
5. Plug the 12 pin male connector of the RVCFD- T-Harness into factory Display. 79A
6. Connect White Wire labeled Reverse Output,12V 500 β€œmA” to the camera +12V Power wire.
7. Connect Black Wire labeled Camera Ground the camera Ground wire. β€œ β€œ to ’s
NOTE: DO NOT connect the camera ground wire to chassis.
8. Connect the Yellow female RCA labeled β€œVDO signal Input” to camera (Not included)
rev.0 82718
2 / 3
Note on the White wire:
a. After the Reverse Gear is disengaged, the White wire will stay powered for up to 11 seconds.
b. White wire will generate 12V Output while Force RVC enable
9 The battery voltage should be maintained above 12.5 volts during the coding process. Make sure .
to turn off the head light, HVAC or any other accessories that may put a load on the car battery.
10. Switch Ignition to ON, turn radio ON an wait until the Radio performs its normal operation. d
11. Set D Switch# 2 from OFF to ON. IP
Upon completion of the coding process the radio display may reboot. This is normal. ,
12. To test the reverse camera, start the engine, verify that the surroundings is clear and put vehicle
into reverse. Verify the that reverse camera image is shown on the display screen.
Note that the vehicle’s VIN number is stored in the module and cannot be used in another
vehicle.
The display screen will have a Blue image if no camera is connected.
Refer to LEDs status for trouble shooting, if necessary.
Force RVC Camera Feature:
The RVCFD- A has a Force RVC feature which allows the viewing of the reverse camera at any time. 79
To use this feature, set DIP switch# 4 to ON and apply +12V to the Green wire. You can use a toggle
switch (not included) between +12V and the Green wire to have the option of turning this feature
ON and OFF.
DIP SWITCH SETTING
DIP 1
OFF
VIM Disable
DIP 2
ON
Rear-View Camera Enable
DIP 3
OFF
N/A
DIP 4
OFF
Option for GREEN Wire
DIP 5
ON
CAN Termination Radio Side
DIP 6
ON
CAN Termination Car Side
FORD LINCOLN
2013 2014 –
2012 2017 –
2013 2016 –
2013 2017 –
2013 2014 –
2013 2016 –
2013 2016 –
2013 2016 –
2013 2016 –
2015
2014 2017 –
C-MAX
Edge
Explorer
F- 150
F- 250
F-450/550 Super Duty
Fiesta
Flex
Focus
Fusion
Taurus
Transit 150
Transit Connect
2015 - 2016
MKX
NOTE: Not compatible with manual transmission or diesel powered trucks.
rev.0 82718
3 / 3


Product specificaties

Merk: CRUX
Categorie: Achteruitrijcamera
Model: RVCFD-79A

Heb je hulp nodig?

Als je hulp nodig hebt met CRUX RVCFD-79A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Achteruitrijcamera CRUX

Handleiding Achteruitrijcamera

Nieuwste handleidingen voor Achteruitrijcamera