Crestron USB-EXT Handleiding

Crestron Wifi-repeater USB-EXT

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron USB-EXT (4 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

quickstart guide

USB-EXT

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

USB-EXT

QUICKSTART DOC. 7204A (2031178) 05.11

USB over Twisted Pair Extender

The Crestron® USB over Twisted Pair Extender (USB-EXT) delivers

reliable USB signal extension for use in a boardroom, classroom,

auditorium, command center, or residence. Without any special setup

or configuration, the USB-EXT enables wire runs up to 100 meters

(~330 feet) over a single, low-cost twisted-pair cable.

The USB-EXT is compatible with USB 1.1 and High-Speed USB 2.0,

supporting virtually any USB device such as keyboards and mice,

game controllers, cameras, mobile devices, printers, hubs, and

memory devices. It is compatible with Windows® and Mac®

computers without requiring any additional drivers.

The USB-EXT is composed of two extender components. The “local”

extender connects to your computer or other USB host, while the

“remote” extender provides connections for your USB devices at

some remote location. Linking the two extender components requires

just one run of inexpensive CAT5 (or better) twisted-pair cable.

The USB-EXT contains a local extender, remote extender, power

supply and a USB cable.

Introduction

NOTE: Crestron does not guarantee that all USB devices are

compatible with the USB-EXT.

On the local and remote units, check that the LEDs are on and that the Power, Host and Link Activity LED for the connected

USB port is blinking. If any LED is permanently off, then the cabling between the local and remote units is not properly installed

or is defective.

Verify device is properly installed on computer:

For Windows Users:

Open Device Manager to confirm that that USB-EXT has been installed correctly. Expand the entry for Universal Serial Bus

controllers by clicking the + sign. If the USB-EXT has been installed correctly, you should find it listed as a “Generic USB

Hub”.

For Mac OS X Users:

Open the System Profiler to confirm that the USB-EXT has been installed correctly. In the left hand column under Hardware,

select “USB” and inspect the right hand panel. If the USB-EXT has been installed correctly you should find it listed as a

“Hub” under the USB High-Speed Bus/USB Bus.

If the unit is not detected correctly or fails to detect, please consult the Troubleshooting section on the following page.

5Checking the Installation

For Regulatory Compliance information,

refer to the latest version of Doc. 7205.

1. On the PC, install any software required to operate the USB device(s). Refer to the documentation for the USB device(s) as

required.

2. Connect the USB device to either USB port on the front of the remote extender.

3. Check that the device is installed and detected properly by the operating system.

4Connecting a USB Device

Remote Extender Front Remote Extender Rear

Local Extender Front

Local Extender Rear

Power

Link

Host

A yctivit

To USB hub or

USB HID devices

To AC Outlet

To PC or

USB Hub

CAT5 Cable

Link Link

DC IN 24V @ 1A

Power

L kin

H tos

Activity

After determining where the local computer and remote USB

device(s) are to be placed, place the local and remote boxes of

the USB-EXT on a flat surface near each of the two locations.

The rubber feet help ensure the units do not slip.

2Mounting

1. Insert the supplied USB cable in the local extender and in an

available USB Type A port on the computer.

2. Using CAT5 (or better) cable, connect the Link ports of the local

and remote extenders.

3. Plug the power adapter into the local extender and then plug the

24V power adapter into an AC outlet.

3Installing

NOTE: If using pre-installed in wall CAT5 wiring, plug one end of the

CAT5 patch cable (not supplied) into the port on the local Link

extender. Plug the other end of the patch cord into the wall outlet

near the host computer. Plug one end of the second CAT5 patch

cord (not supplied) into the port on the remote extender. Plug Link

the other end of the second patch cable into the wall outlet near the

USB device. Make sure that the two patch cables and in wall cabling

does not exceed 100M (~330 feet).

quickstart guide

USB-EXT

www.crestron.com

888.273.7876 201.767.3400

Specifications subject to

change without notice.

USB-EXT

QUICKSTART DOC. 7204A (2031178) 05.11

USB over Twisted Pair Extender

For Regulatory Compliance information,

refer to the latest version of Doc. 7205.

The following table provides corrective action for possible trouble situations. If further assistance is required, please contact a Crestron customer service representative.

Troubleshooting

TROUBLE POSSIBLE CAUSE(S) CORRECTIVE ACTION

Ensure that the AC power adapter is properly connected to the local extender. No LEDs on the local extender

illuminate.

The local extender is not receiving power from the AC

power adapter. Check that the AC adapter is connected to a live power source.

Ensure that the CAT5 cabling between the local and remote extender is properly installed. No LEDs on the remote extender

illuminate.

The remote extender is not receiving power over the

CAT5 cable. Verify power pack connection to local extender and AC power source. Check that the local extender Power LED

is illuminated.

There is no connection between the local and remote

extenders.

Ensure CAT5 cable is connected between the local and remote extenders. CAT5 cable, or better, UTP with a

straight through connector and no crossovers, and eight connector RJ-45 connectors are used at both ends.

Link LEDs on local extender and remote

extender are off.

The CAT5 cable is defective. To determine if the CAT5 cable is defective connect a short CAT5 patch cord between the two units.

The host computer is not powered on. Power on host computer.

The local extender is not connected to the computer. Check that the local extender is properly connected to the computer.

The computer does not support USB hubs. Connect the USB-EXT to a PC that supports USB hubs.

Link LEDs for local extender is

illuminated but Host LED is off.

The USB-EXT is malfunctioning. Complete the following procedure:

1. Disconnect power to the local extender.

2. Disconnect all USB devices from the remote extender.

3. Disconnect the local extender from the computer.

4. Reconnect the local extender to the computer.

5. Reapply power to the local extender

6. In Windows, make sure that the devices is recognized as a “Generic USB Hub” in the Universal Serial Bus

controllers section of the Device Manager.

Loss of functionality due to electrostatic

discharge.

Improper grounding. Check that all ground connections have been made properly.

The remote unit is in suspend mode. The operating

system may put the USB-EXT in suspend mode when a

computer is put into a suspend/standby state.

Recover/resume the operating system from suspend/standby mode. USB-EXT device was working but the

Host LEDs on the local and remote

extenders are now blinking.

No USB devices are attached. Attach a USB device to the USB-EXT.

The USB device is malfunctioning

The computer does not recognize the USB device.

The application software for the device is not operating

All LEDs on both the local extender and

remote extender are on, but the USB

device does not operate correctly, or, is

detected as an “Unknown Device” in the

operating system. The USB-EXT is malfunctioning.

Perform either of the following:

• Disconnect the USB-EXT from the computer and connect it directly to the USB port on the computer. If the

device does not operate properly, consult the user documentation for the device for further troubleshooting.

• If the device operates properly when directly connected to the computer, connect another device (of a

different type) to the USB-EXT. If the second device does operate properly, the first device may not be

compatible with the USB-EXT.

If the steps above do not solve the issue, update your system BIOS, chipset or USB host controller drivers from

your System/Mother board manufacturer’s Web site.

USB device is attached to either of the

remote USB ports but the associated

USB LED is off.

A USB device must have the appropriate driver installed

on the computer.

Install the USB device driver on the computer prior to attaching the USB device to the remote extender. Refer to

your USB device manufacturer’s eb site for details.W

USB LED on remote extender is orange

and device is not functioning

Overcurrent condition has occurred because USB

device draws more power than can be supplied per USB

specification (500 mA).

Power cycle the local extender.

Use a different local/remote pair which have the same firmware revision.

Host and Link LEDs on the local and

remote extender blink intermittently.

Firmware mismatch between the local and remote

extender. Contact Crestron customer support as the firmware may need to be upgraded.

Crestron and the Crestron logo are trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and other countries. Mac is a trademark or registered trademark of Apple, Inc. in the United States and/or other countries. Windows is a registered trademark or trademark

of Microsoft Corporation in the United States and/or other countries. Other trademarks and trade names may be used in this doc n the marks and names of others.ument to refer to either the entities claiming the marks and names or their products. Crestron disclaims proprietary interest i

Product specificaties

Merk:	Crestron
Categorie:	Wifi-repeater
Model:	USB-EXT
Kleur van het product:	Zwart
Breedte:	100 mm
Diepte:	76 mm
Hoogte:	26 mm
Soort:	Netwerkzender & -ontvanger
LED-indicatoren:	Ja
Stroom:	1 A
Aantal USB 2.0-poorten:	3
Aantal Ethernet LAN (RJ-45)-poorten:	2
Externe adapter:	Ja
Maximaal bereik:	100 m
Overdrachtssnelheid:	480 Mbit/s
AC-ingangsspanning:	24 V
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	20 - 80 procent
Ondersteundende kabel types:	Cat5