Crestron HD-TX1-F Handleiding

Crestron Wifi-repeater HD-TX1-F

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron HD-TX1-F (2 pagina's) in de categorie Wifi-repeater. Deze handleiding was nuttig voor 45 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

quickstart guide

HD-TX and HD-RX Series

www.crestron.com

Specifications subject to

change without notice.

For Regulatory Compliance information, refer to

the latest version of Doc. 6860.

QUICKSTART DOC. 6861D (2025032) 08.16

HDMI® Fiber-Optic Transmitters and Receivers

The HD-TX and HD-RX Series consist of the following models:

• HD-TX1-F transmitter and HD-RX1-F receiver

• HD-TX3-F transmitter and HD-RX3-F receiver

1Introduction

HD-TX1-F Front Panel Connections

Connecting the HDMI IN Port: Using an HDMI cable (not

supplied), connect the HDMI IN port to the HDMI output port of

the audio/video source.

Connecting the Control Ports: Connect the IR IN or COM

control port or both as follows:

• Using an IR cable (not supplied), connect the 2-pin IR IN:

terminal block of the IR IN port to the IR output port of the

control system.

• : Using a data communications cable (not COM (RS-232)

supplied), connect the 3-pin terminal block to the COM port

of the control system.

HD-RX1-F Front Panel Connections

Connecting the HDMI OUT Port: Using an HDMI cable (not

supplied), connect the HDMI OUT port to the HDMI input port of

the receiving device.

Connecting the Control Ports: Connect the IR OUT or COM

control port or both as follows:

• : Using the CrestronIR OUT ®

IRP2 emitter (not supplied),

connect the 2-pin terminal block of the IR OUT port to the

IR input port of the device to be controlled.

• : Using a data communications cable (not COM (RS-232)

supplied), connect the 3-pin terminal block to the COM port

of the device to be controlled.

HD-TX1-F and HD-RX1-F Rear Panel Connections

Connecting the Ground: Connect the chassis ground lug to

earth ground (building steel).

Connecting the MM OPTICAL Fiber Port: Using a CresFiber

or other quality 50/125 μm or 62.5/125 μm simplex multimode

fiber-optic cable with SC connectors, connect one end of the

cable to the MM OPTICAL connector on the HD-TX1-F and the

other end of the cable to the MM OPTICAL connector on the

HD-RX1-F.

NOTE: For maximum distance, the fiber-optic

cable should be rated for at least 500 MHz*km

effective modal bandwidth (EMB) at both 850 nm

and 1300 nm. Refer to the cable manufacturer’s

datasheet for EMB information.

Connecting the 12 Vdc Power Jack:

Connect the 12 Vdc power jack to the

PW-1205RU external power supply included

with the HD-TX1-F and HD-RX1-F.

3HD-TX1-F and HD-RX-1 Connections

HD-TX and HD-RX Series

Mount the transmitter and receiver onto a wall or rack as

appropriate for your installation.

Wall Mounting

Using four mounting screws (not supplied), attach the

transmitter or receiver to the wall as shown below.

Rack Mounting

Mount the transmitter or receiver to the front or rear rail of a

rack as follows:

1. Position either the left or right mounting flanges of the

device so that the holes align with the holes in the rack

(mounting of right flanges is shown below).

2. Secure the device to the rack using two rack mounting

screws (not supplied).

2Mounting

(4) Mounting screws

(not supplied)

Rack mounting

screws

(not supplied)

HD-TX1-F Front Panel Connections

COM

GND

HDMI OUT

IR OUT

S G

Display

HD-RX1-F Front Panel Connections

GND

HDMI IN

IR IN

S G

COM

source

Control

system

HD-TX1-F Rear Panel Connections HD-RX1-F Rear Panel Connections

MM OPTICAL

0.5A

12VDC

CLASS 1

LASER

PRODUCT

USB port

(for factory

use only)

MM OPTICAL

0.5A

12VDC

CLASS 1

LASER

PRODUCT

Fiber-optic cable

USB port

(for factory

use only)

Ground Ground

Power

supply

Power

supply

quickstart guide

HD-TX and HD-RX Series

www.crestron.com

Specifications subject to

change without notice.

HD-TX and HD-RX Series

For Regulatory Compliance information, refer to

the latest version of Doc. 6860.

QUICKSTART DOC. 6861D (2025032) 08.16

HDMI Fiber-Optic Transmitters and Receivers

HD-TX3-F Front Panel Connections

Connecting the AUDIO Input Port: Using an unbalanced

3.5 mm TRS mini phone jack cable (not supplied), connect the

AUDIO input port to an unbalanced audio source.

Connecting the USB HID Port: Using a USB cable (not

supplied), connect the USB HID port to a computer.

Connecting the HDMI IN Port: Using an HDMI cable (not

supplied), connect the HDMI IN port to the HDMI output port of

the audio/video source.

Connecting the LAN Port: Using an Ethernet cable (not

supplied), connect the 10BASE-T/100BASE-TX LAN port to the

LAN. Pin designations are listed below.

LAN Port Pin Designations

HD-TX3-F Front Panel Connections

4HD-TX3-F and HD-RX3-F Connections

The specific patents that cover Crestron products are listed at

patents.crestron.com.

Certain Crestron products contain open source software. For specific information,

please visit www.crestron.com/opensource.

Crestron, the Crestron logo, and CresFiber are either trademarks or registered

trademarks of Crestron Electronics, Inc. in the United States and/or other

countries. HDMI is either a trademark or registered trademark of HDMI Licensing

LLC in the United States and/or other countries. Other trademarks, registered

trademarks, and trade names may be used in this document to refer to either the

entities claiming the marks and names or their products. Crestron disclaims any

proprietary interest in the marks and names of others. Crestron is not responsible

for errors in typography or photography.

This document was written by the Technical Publications department at Crestron.

AUDIO

USB HID

HDMI IN

LAN

Audio

source

Computer

LAN

Pin 1Pin 8

source

LAN

HD-RX3-F Front Panel Connections

Connecting the AUDIO Output Port: Using an unbalanced

3.5 mm TRS mini phone jack cable (not supplied), connect the

AUDIO output port to an unbalanced audio output device.

NOTE: When the HDMI IN (HD-TX3-F) or HDMI OUT

(HD-RX3-F) port is connected or disconnected or if the HDMI

input resolution changes, the analog audio output is muted for a

few seconds.

Connecting the USB HID Port: Using a USB cable (not

supplied), connect the USB HID port to a mouse or keyboard.

(A keyboard with a built-in touchpad or trackball is supported.

Built-in and external USB hubs are not supported.)

Connecting the HDMI OUT Port: Using an HDMI cable (not

supplied), connect the HDMI OUT port to the HDMI input port of

the receiving device.

Connecting the LAN Port: Using an Ethernet cable (not

supplied), connect the 10BASE-T/100BASE-TX LAN port to the

LAN. (LAN port pin designations are listed in the table in the

left-hand column.)

HD-RX3-F Front Panel Connections

HD-TX3-F and HD-RX3-F Rear Panel Connections

Connecting the Control Ports: Connect the IR or COM

control port or both as follows:

• : Using an IR cable (not supplied), IR IN (HD-TX3-F)

connect the 2-pin terminal block of the IR IN port to the IR

output port of the control system.

• : Using the Crestron IRP2 emitter (not IR OUT (HD-RX3-F)

supplied), connect the 2-pin terminal block of the IR OUT

port to the IR input port of the device to be controlled

• : Using a data communications cable (not COM (RS-232)

supplied), connect the 3-pin terminal block as follows:

- For the HD-TX3-F, connect the COM port to the COM

port of the control system.

- For the HD-RX3-F, connect the COM port to the COM

port of the device to be controlled.

HDMI OUT

AUDIO

USB HID LAN

Display

LAN

Powered

speakers

Mouse or

keyboard

LAN

Pin 1Pin 8

HD-TX3-F Rear

Panel Connections

HD-RX3-F Rear

Panel Connections

IR IN

S G

COM

GND

MM OPTICAL 12VDC

1.5A IR OUT

S G

COM

GND

MM OPTICAL 12VDC

1.5A

Ground

USB port

(for factory

use only)

USB port

(for factory

use only)

Power

supply

Fiber-optic cable

Power

supply

Control

system Display

CLASS 1

LASER

PRODUCT

CLASS 1

LASER

PRODUCT

Connecting the MM OPTICAL Fiber Port: Using a CresFiber or other

quality 50/125 μm or 62.5/125 μm simplex multimode fiber-optic cable with

SC connectors, connect one end of the cable to the MM OPTICAL

connector on the HD-TX3-F and the other end of the cable to the MM

OPTICAL connector on the HD-RX3-F.

NOTE: For maximum distance, the fiber-optic cable should be rated for at

least 500 MHz*km effective modal bandwidth (EMB) at both 850 nm and

1300 nm. Refer to the cable manufacturer’s datasheet for EMB information.

Connecting the Ground: Connect the chassis ground lug to earth ground

(building steel).

Connecting the 12 Vdc Power Jack: Connect the 12 Vdc power jack to

the PW-1215WU external power supply included with the HD-TX3-F and

HD-RX3-F.

PIN SIGNAL PIN SIGNAL

1 TX+ 5 N/C

2 TX– 6 RX–

3 RX+ 7 N/C

4 N/C 8 N/C

Product specificaties

Merk:	Crestron
Categorie:	Wifi-repeater
Model:	HD-TX1-F
Kleur van het product:	Black, Grey
Gewicht:	416 g
Breedte:	100 mm
Diepte:	37 mm
Hoogte:	150 mm
Soort:	Netwerkzender
Materiaal behuizing:	Aluminium
LED-indicatoren:	Stroom
Aansluiting voor netstroomadapter:	Ja
Output current:	0.5 A
Spanning:	12 V
Maximaal bereik:	300 m
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Vezel-optische connector:	SC