Crestron TST-600-BTP Handleiding

Crestron Niet gecategoriseerd TST-600-BTP

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron TST-600-BTP (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 4 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

DO GUIDE

DO Check the Box

QUANTITY PRODUCT PART NUMBER

2 Tape, Perforated, 1" x 1" 2023162

1 Tape, Perforated, 1" x 2" 2023163

1 Metal T-Pin 2020478

TST-600-BTP

Battery Pack for TST-600 and TST-602

The Crestron® TST-600-BTP consists of two battery cells along with the

integrated wiring. It has a multipin connector that attaches to the inside of

the TST-600 or TST-602.

TST-600-BTP with Multipin Connector

DO Remove the Old Battery Pack

NOTE: The TST-600 and TST-602 Wireless Touch Screens contain

electrostatic discharge (ESD) sensitive devices. To avoid damaging the

unit, perform the following procedure while wearing a grounding strap

that is properly grounded or while working on a grounded workstation.

NOTE: To prevent damage to the multipin connector and wiring, use care

when handling the TST-600-BTP.

Perform the following procedure to remove the existing TST-600-BTP

from a TST-600 or TST-602 touch screen. A #1 Phillips screwdriver is

required.

1. Use the included T-pin to slide the battery switch on the rear to the

off (down) position. Then place the touch screen face down on a

clean, padded work surface.

2. Remove the four screws that secure the front bezel to the touch

screen and return the unit to its normal, face-up position. (Use care

and hold the bezel against the touch screen.)

3. Unsnap the front bezel and lift it off of the touch screen and then

place the touch screen assembly face down on the work surface.

4. Carefully remove the rear of the enclosure from the touch screen

by grasping the support frame at the left and right edges, gently

spreading the edges (as shown in the following image), and then

lifting the assembly. It snaps out of the enclosure.

5. Remove the orange tape securing the battery pack wires to the

assembly.

6. Gently separate the multipin connector from the corresponding

connector on the circuit board of the touch screen.

7. Remove battery cells, with the connecting wires attached, from both

sides of the assembly.

DO Install the New Battery Pack

NOTE: The TST-600 and TST-602 Wireless Touch Screens contain

electrostatic discharge (ESD) sensitive devices. To avoid damaging the

unit, perform the following procedure while wearing a grounding strap

that is properly grounded or while working on a grounded workstation.

After removing the old TST-600-BTP from the touch screen, perform

the following procedure to install the new TST-600-BTP. A #1 Phillips

screwdriver is required.

1. Inspect the wire insulation on the battery pack and verify that it

extends to the battery wrap and is free of nicks or damage.

2. Orient the TST-600-BTP so the wires exiting the battery are facing

the connector on the touch screen.

3. Slide the right stack wires (those closest to the connector) into the

PCB channel, angling the top of the stack into the pocket of the ex

support tray.

4. Fully seat the right stack into the right pocket of the ex support tray

and verify that the wires have not been damaged during installation.

5. Connect the battery pack harness to the PCB connector.

6. With the wire harness positioned above the installed insulator, slide

the left stack wires into the PCB channel, angling the top of the stack

into the pocket of the ex support tray.

7. Fully seat the left stack into the left pocket of the ex support tray

and verify that the wires have not been damaged during installation.

8. Verify that the battery pack is connected and that the stacks are fully

seated into the left and right pockets.

9. Dress the battery wires as shown in the following image. Use the

2 1/2 inch (64 mm) long piece of orange tape to secure the wires.

NOTE: When routing the wires, avoid blocking the battery switch.

Battery Cells

Connector

Connectors

The connectors are aligned.

Seat the right stack in

the ex tray.

Screws Screws

DO GUIDE DOC. 7690A (2041543) 12.14

Specications subject to change without notice.

DO Replace the PCB Assembly

Replace the PCM assembly into the rear enclosure using the following

procedure:

1. Carefully begin to install the PCB assembly at an angle with the top

end rst into the rear of the enclosure.

2. Slide the speaker assembly section of the PCB into the slot in the

rear enclosure, ensuring the wires are pushed up. Then, place the

bottom end of the PCB assembly into the housing.

3. Verify that the speaker cables are properly positioned above the

PCB.

4. Gently press the PCB assembly into the rear enclosure, snapping the

assembly into position at the six locations shown below.

5. Carefully install the front bezel at an angle placing the top end rst.

6. Gently press on bezel locations shown in the following image until

the bezel locks into the ex support trays and a click is heard.

7. Secure the rear enclosure to the front enclosure using the four

screws.

8. Reconnect the power by sliding the battery switch on the rear to the

on (up) position.

DO Charge the Battery Pack

To charge the TST-600-BTP, install the TST-600-BTP in the touch screen

and mount the touch screen on a powered TST-600-DS docking station.

NOTE: The battery pack may take up to ve hours to charge in a

powered touch screen if the panel is in use while charging.

DO Store the Battery Pack

The TST-600-BTP can be stored in a temperate, dry place (removed from

the touch screen and docking station) for up to three months without

signicant irreversible degradation of its performance. The self-discharge

rate is a function of temperature and internal resistance. High temperature

storage reduces charge retention. Best results occur if the TST-600-BTP

is stored at an optimal temperature of 32° to 95°F (0° to 35°C).

NOTE: Li-ion batteries must be stored at 50% charge and cycled every

three months.

DO Dispose of the Battery Pack

NOTE: The TST-600-BTP contains a lithium ion battery. When the unit

can no longer retain a charge, it must be recycled or disposed of properly.

Follow local ordinances and regulations for disposal.

NOTE: The battery must be recycled. Deliver the battery pack

to an appropriate recycling facility.

As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.

Crestron product development sof t ware is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transf erable Soft ware Development Tools License Agreement. Crestron product operat ing system sof t ware is licensed to Crestron dealers, CSPs, and

end-users under a separat e End-User License Agreement. Both of these Agreements can be found on t he Crestron website at www.crest ron.com/legal/sof t ware_license_agreement.

The specic patents that cover Crestron products are listed at www.patents.crestron.com. Product warranty can be found at www.crestron.com/warranty.

Crestron and the Crestron logo are eit her t rademarks or registered trademarks of Crestron Elect ronics, Inc. in the United States and/or other countries. Ot her t rademarks, registered trademarks, and trade names may be used in this document to refer t o either the ent ities claiming the marks and

names or their product s. Crestron disclaims any proprietary int erest in the marks and names of others. Crestron is not responsible f or errors in t ypography or photography.