Crestron TSR-302-B Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron TSR-302-B (2 pagina's) in de categorie Afstandsbediening. Deze handleiding was nuttig voor 39 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
DO GUIDE
TSR-302
Handheld Touch Screen Remote
DO Install the Battery
To install the TSR-302-BTP, perform the following procedure:
1. Remove the battery compartment cover on the rear of the TSR-302
by using two thumbs and gently pressing in the direction of the arrow
shown.
2. Place the touch screen remote, with the screen side down, on a clean,
soft surface.
3. Place the TSR-302-BTP in the battery compartment, oriented as
shown.
4. Reattach the battery compartment cover by pressing down lightly on
the locking tab while sliding the cover into place.
DO Congure the Device
The main setup screen is the starting point for conguring the Crestron
®
TSR-302. If no project is loaded, tap the screen to access the main setup
screen. If a project is running, the main setup screen can be accessed by
pressing (Power), (Home), MENU, and in sequence twice GUIDE
( , , MENU, , , , GUIDE MENU, ) within a 5-second GUIDE
period.
The main setup screen can also be accessed via Crestron Toolbox
software.
1. Establish communication with the TSR-302.
2. Right-click on the device and select .Functions > Setup Mode
3. to display the main setup screen.Select Enter Setup Mode
NOTE: Select to exit the setup screens.Exit Setup Mode
NOTE: From any of the setup screens, tap to go back to the
previous screen.
For details on conguring the TSR-302, refer to Doc. 7663 at
www.crestron.com/manuals.
DO Set Up Basic Wireless
Before a TSR-302 can be used with a Crestron control system, it must rst
be acquired by a Crestron Extended Range (ER) Wireless Gateway (sold
separately).
To acquire a TSR-302, perform the following procedure:
1. Use a stylus or other thin-tipped object to press ACQUIRE on the
gateway to enter Acquire mode. The accompanying LED illuminates,
indicating the unit is ready to link with the touch screen. (The gateway
can also be put into Acquire mode via Crestron Toolbox.)
2. From the main setup screen on the TSR-302, tap to display RF Setup
the screen. At the bottom of the RF Setup RF Setup screen, select
2-Series or , depending on whether a 2-Series or 3-Series3-Series ®
control system is being used. Then place the TSR-302 in Acquire
mode by tapping Acquire on the RF Setup screen. The screen
displays an “Acquire in progress” message, and the TSR-302 is
automatically acquired by the gateway within 2 minutes.
3. When the process is complete, the screen displays an “Acquire OK”
message. Press on the gateway to exit Acquire mode. The ACQUIRE
LED turns off.
For information on wireless setup with roaming, refer to “Gateway Roaming
Setup” in Doc. 7663.
DO Set Up Wi-Fi
To set up a Wi-Fi® connection, on the main setup screen tap , WiFi Setup
and then tap Add Access Point Select Access Point to display the
screen.
If the desired wireless access point is already on the list, tap .Connect
Otherwise, perform the following procedure to add a new access point:
1. Tap Add New to display the Conrm Info screen.
2. Tap the WAP Name (SSID)eld to open an on-screen keyboard,
which can be used to enter the name.
3. Tap the eld to display the Security Encryption screen.
4. Select the appropriate type of encryption, and then tap to return
to the Conrm Info screen.
5. Tap the Password eld to open an on-screen keyboard, which can be
used to enter the password.
6. to save the password and return to the Tap Save Conrm Info
screen.
DO Check the Box
QUANTITY PRODUCT COLOR PART NUMBER
1 Battery Pack, Rechargeable, TSR-302-BTP 2039523
1 Dock, Table, TSR-302-DS 4520465
1 Power Pack, 19 Vdc, 0.9 A, 100-240 Vac 2045868
DO GUIDE DOC. 7661C (2040912) 02.16
Specicat ions subject to change without not ice.
7. Tap Make this my Access Point to conrm the entries and display
the WAP Connect screen.
8. to accept the connection to the wireless access point and Tap Done
to display the WiFi Setup screen.
9. Tap IP Settings to display the WiFi IP Settings screen.
10. To use DHCP, tap repeatedly to return to the main setup screen.
11. To enter static IP settings, tap Off under DHCP Enabled. The
TSR-302 ships with DHCP enabled by default.
12. Tap Set Static IP Address Settings to display the Static IPs screen.
13. Tap the Static IP address eld to open an on-screen, numeric
keypad.
14. Enter the address and tap to return to the Save Static IPs screen.
15. Tap each of the rest of the elds in turn and enter its address, and then
tap Save.
16. Tap to return to the WiFi IP Settings screen.
17. Tap Reboot Required to Apply IP Changes.
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the users authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference and (2) this device must accept
any interference, including interference that may cause undesired operation of the device.
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
Industrie Canada (IC) Déclaration de conformité
Le présent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas
produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Conformément à la réglementation d’Industrie Canada, le psent émetteur radio peut fonctionner avec une antenne d’un type et d’un gain maximal (ou inrieur) approuvé pour l’émetteur par Industrie
Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la puissance isotrope rayonnée
équivalente (p.i.r.e.) ne dépasse pas l’intensité nécessaire à l’établissement dune communication satisfaisante.
To satisf y RF exposure requirements, t his device and its antenna must operate with a separation dist ance of at least 20 centimeters from all persona and must not be colocated in conjunction with any other ant enna or transmit ter. For operation within t he 5.15-5.25 GHz band, it is restricted to
indoor use.
Crest ron product development soft ware is licensed to Crest ron dealers and Crest ron Service Providers (CSPs) under a limited non-exclusive, non-t ransferable Soft ware Development Tools License Agreement. Crestron product operating system sof t ware is licensed to Crest ron dealers, CSPs,
and end-users under a separate End-User License Agreement. Both of these Agreement s can be found on the Crestron website at .ww w.crestron.com/legal/sof tware _license_agreement
The specic patents t hat cover Crestron products are listed at . The product warrant y can be found at .patent s.crest ron.com www.crestron.com/warrant y
Crest ron, t he Crestron logo, 3-Series, Crestron Toolbox, and inNET EX are either t rademarks or registered trademarks of Crestron Electronics, Inc., in t he United St ates and/or ot her count ries. Wi-Fi, WPA and WPA2 are either trademarks or registered trademarks of Wi-Fi Alliance in the United
States and/or other countries. Other trademarks, regist ered t rademarks, and trade names may be used in this document to refer to either the entities claiming the marks and n ames or their products. Crestron disclaims any proprietary int erest in t he marks and names of ot hers. Crestron is not
responsible for errors in t ypography or phot ography.
This document was writ ten by the Technical Publications depart ment at Crest ron.
©2016 Crestron Electronics, Inc.
DO Learn More
Visit the website for additional information and the latest rmware updates. To learn more about this product, use a QR reader application on
your mobile device to scan the QR image.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com


Product specificaties

Merk: Crestron
Categorie: Afstandsbediening
Model: TSR-302-B

Heb je hulp nodig?

Als je hulp nodig hebt met Crestron TSR-302-B stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Afstandsbediening Crestron

Handleiding Afstandsbediening

Nieuwste handleidingen voor Afstandsbediening