Crestron GLS-OIR-C-CN Handleiding

Crestron Smarth home GLS-OIR-C-CN

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron GLS-OIR-C-CN (2 pagina's) in de categorie Smarth home. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Crestron Electronics, Inc. Installation Guide - DOC. 7529A

15 Volvo Drive Rockleigh, NJ 07647 (2036482)

Tel: 888.CRESTRON 09.13

Fax: 201.767.7576 Specifications subject to

www.crestron.com change without notice.

This product is Listed to applicable

UL Standards and requirements by

Underwriters Laboratories Inc.

Further Inquiries

To locate specific information or resolve questions after reviewing this guide, contact Crestron's True Blue Support at

1-888-CRESTRON [1-888-273-7876] or, for assistance within a particular geographic region, refer to the listing of

Crestron worldwide offices at www.crestron.com/offices.

To post a question about Crestron products, log onto Crestron’s Online Help at www.crestron.com/onlinehelp.

First-time users must establish a user account to fully benefit from all available features.

Future Updates

As Crestron improves functions, adds new features and extends the capabilities of the GLS-OIR-C-CN, additional

information may be made available as manual updates. These updates are solely electronic and serve as

intermediary supplements prior to the release of a complete technical documentation revision.

Check the Crestron Web site periodically for manual update availability and its relevance. Updates are identified as

an “Addendum” in the Download column.

WARNING: To avo ock or deid fire, sh , ath turn; off po rc ea use nd power is be ore wer at ci uit br ker or f a test that off f

wiring!

NOTES: Observe the following points.

• To be installed and/or used in accordance with appropriate electrical codes and regulations.

• This product should be installed by a qualified electrician.

• Sensors must be mounted on a vibration free surface.

PREPARING AND CONNECTING WIRES

Strip the ends of the wires approximately 1/4 in (6 mm). Use care to avoid nicking the conductors. Twist together

the ends of the wires that share a connection. Apply solder only to the ends of the twisted wires. Avoid tinning too

far up the wires or the ends become brittle.

Crestron GLS-OIR-C-CN

Passive Infrared Occupancy Sensor with Cresnet ®

Installation Guide

DESCRIPTION

The Crestron® Passive Infrared Occupancy Sensor with Cresnet

® is a low-voltage passive

infrared (PIR) sensor that is directly wired through Cresnet to automatically control lighting or

any other system wide device. The sensor is typically used to turn lights on when a room or

area is occupied and to shut them off when the room or area is vacated. The exact behavior

of the sensor can be configured via software or the IR remote (GLS-REMOTE-ODT/OIR,

sold separately). The passive infrared motion detection provides high immunity to false

triggering and yields a sensor with a 360 degree 2000 square feet coverage area with

excellent performance. Additionally, an integrated photocell allows for easy and custom

adjustments for even the most robust of daylight harvesting applications.

MOUNTING/MASKING LOCATION DIAGRAM

The supplied masks mount in the sensor cover to block the PIR sensor. The half mask is

supplied to allow half of the sensor to be masked. The perforated mask has twelve 30º

removable segments that allow masking particular areas to prevent undesireable triggers

from affecteng the sensor operation.

Masking is not required in the corner mounting application shown below because it cannot

see through a door. By masking a portion of the sensor, traffic through a hallway can be

ignored as in the second example. The following illustrations provide typical application

examples.

TYPICAL APPLICATION DIAGRAMS

The following diagrams illustrate the typical wiring of a GLS-OIR-C-CN.

Wire GLS-OIR-C-CN

INSTALLATION

The GLS-OIR-C-CN can be installed into a drop ceiling, drywall, or an octagon electrical box.

Refer to the instructions that follow to install the sensor.

The following items are included with the GLS-OIR-C-CN for installation:

1/2 Solid PIR mask (1)•

1/12 Perforated PIR mask (1)•

Hole cutout template (1)•

The following items are required for installation:

Slotted/Phillips screwdriver•

• Pencil

Cutting tools•

NOTE: Before securing the sensor to the ceiling, refer to the “Mounting/Masking Location”

and “Detection Range” sections to choose the best orientation. Avoid areas where false

tripping may occur due to outside motion such as an open door. Identify and avoid areas of

possible vibrations and air currents (e.g., projectors, fans, vents) and mount the sensor at

least 5 feet (2 meters) away from these items.

Install Into Drop Ceiling or Drywall

1. Select the location for mounting the sensor and proper masking for the application.

2. Use the supplied hole cutout template to mark the ceiling where the sensor is to be

mounted.

3. Use cutting tools appropriate for the surface to create a hole in the ceiling.

4. Turn the sensor cover counterclockwise to separate it from the GLS-OIR-C-CN.

Install Into Octagon Electrical Box

1. Select the location for mounting the sensor and proper masking for the application.

2. Turn the sensor cover counterclockwise to separate it from the device.

3. Using a Phillips screwdriver, unscrew the the preinstalled screws from the plastic wings

and remove them from the sensor.

4. Mount the GLS-OIR-C-CN to the octagon electrical box using two screws (not

supplied).

Mounting to Octagon Electrical Box

Cresnet

Crestron

Control System

or CLS-C6

External

Photocell

Cresnet

Crestron

Control System

or CLS-C6

Octagon

Electrical

Box

GLS-OIR-C-CN

(Cover Removed)

Mounting Screws

(Not Supplied)

Cover

5. Place the GLS-OIR-C-CN into the hole and secure the sensor to the drywall or ceiling

tile using the preinstalled screws. The preinstalled screws have plastic “wings” that

secure the occupancy sensor to the ceiling. When the screws are tightened the wings

open and clamp against the surface of the ceiling. The screws should be secured

tightly enough so that the device cannot spin in the ceiling opening. Refer to the

illustration below for a typical mounting scenario.

Mount GLS-OIR-C-CN to Drywall or Drop Ceiling

6. Place the cover on the device and twist to secure. Align the arrows on the device with

the arrows under the cover. Twist the cover clockwise. The cover snaps into place.

Wire GLS-OIR-C-CN with Photocell

5. Place the cover on the device and twist to secure. Align the arrows on the device with

the arrows under the cover. Twist the cover clockwise. The cover snaps into place.

GLS-OIR-C-CN

(Cover Removed)

Cover

Ceiling

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)



(m)

0 (0)

5 (2)

10 (3)

15 (5)

5 (2)

10 (3)

15 (5)

 (m)

20 (6)

25 (8)

20 (6)

25 (8)

(10)

30 (10)

Top View

8 1/2 ft (2.6 m)

Ceiling Height

DETECTION RANGE

High PIR Sensitivity Setting

The detection pattern for the high PIR sensitivity setting is shown in the illustrations below.

The first illustration shows the side view of the detection range and the second illustration

shows the detection range based on the top view of the sensor.

0 ft (0 m)

8 ft (2.4 m)

8.5 ft (2.6 m)

10 ft (3 m)

12 ft (4 m)

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)

(m)

SIDE VIEW

VERIFY OPERATION

After the GLS-OIR-C-CN is installed its installation location and operation should be verified.

Confirm Installation Location

Verify the installation location by entering the room, closing any doors and sitting in the room

while observing the device’s LED. While sitting still, verify that the sensor only detects actual

motion and is not affected by any projectors, fans, vents, etc. Monitor the LED activity on the

device. A properly installed occupancy sensor should have no LED activity when there is no

motion in the room.

Adjust Occupancy Sensitivity

NOTE: If multiple occupancy sensors are located in the same room, adjust one at a time.

1. Press and hold for 3 seconds on the IR remote to enter OCC SETUP Occupancy

Setup mode.

2. Set the room sensitivity based on the illustrations in the “Detection Range” section on

the previous page.

3. Walk around the room to simulate typical room motion (e.g., sit at various places

around a conference table and simulate typical motion for a conference room).

4. Verify LED indication of motion (red for PIR).

5. Adjust sensitivity levels, if necessary, to maintain occupancy of the room. If no motion

is detected in main areas of the room, increase the sensitivity. If no motion is detected

in the corners of the room, increase the timeout to allow greater chance of detecting

motion.

6. Repeat these steps until all expected motion is detected.

Adjust Vacancy Sensitivity

1. In Vacancy Setup mode, verify that nothing triggers occupancy when the room is

vacant. When in mode the occupancy sensor beeps to indicate motion. Vacancy Setup

The occupancy sensor should beep when re-entering the room.

2. Using the IR remote, place the sensor into vaccancy setup mode by pressing the VAC

SETUP button. Exit the room and close the door.

3. Listen for beeps that indicate there is motion detected in the room.

4. Walk by open door ways or entrances/exits to ensure that no false occupancies are

being detected.

5. If unwanted motion is detected, lower the PIR setting and retest.

TROUBLE POSSIBLE CAUSE CORRECTIVE ACTION

Lights do not

turn on.

Circuit breaker or fuse

has tripped.

Reset circuit breaker or replace fuse.

Incorrect programming

in control system.

Check control system logic or contact

Crestron for assistance

Connection on back of

sensor is miswired.

Check that all Cresnet wires are wired to

their respective terminals.

Incorrect settings on

device.

Increase the sensitivity to the next highest

setting on the PIR sensor.

Incorrect mounting

location.

Move the sensor into an area that can

"see" the occupant or point of motion.

Lights do not

turn off.

Constant motion. To test, reduce sensitivity level and

remove motion source. If there is no

change, then the mounting location must

move.

Sensor can "see" too

far into hallway or other

room.

To test, put the sensor into the Setup

mode and walk by the area. If the red LED

continues to blink, move the sensor or use

masks on the PIR.

Incorrect settings on

device.

Reduce the sensitivity and timeout levels

one step at a time.

Incorrect programming

in control system.

Check control system logic or contact

Crestron for assistance.

Lights remain

on too long.

Timeout setting is too

high.

Reduce the timeout one step at a time.

OPERATION

The descriptions below refer to a system which has been configured to turn the lights on

when a room or area is occupied and turn them off when the room or area is vacated.

• Timeout - The sensor is designed to turn the lights off if no motion is detected after a

specified time. This length of time is called the delayed-off time and is set using the

IR remote. The duration is the amount of time after the last instance of motion until

the lights turn off.

• Short Timeout - This walk-through feature is useful when a room is momentarily

occupied. With this feature, the sensor turns the lights off shortly after the person

leaves the room.

The short-timeout feature works as follows: When a person enters the room, the

lights turn on. If the person leaves the room before the short-timeout threshold of 90

seconds has elapsed, the timeout reverts to 60 seconds in order to turn the lights off

sooner. If the programmed timeout happens to be less than 60 seconds during

normal operation, that timeout value takes precedence.

• LED Operation - The LED flashes when motion is detected. The LED flash can be

disabled using the LED disable switch setting. Red flash indicates motion detection

by passive infrared technology.

PHOTOCELL ADJUSTMENT

The GLS-OIR-C-CN has a built in photocell that allows for complete daylight harvesting

using the Crestron lighting system. Through programming, the photocell can dim lights or

choose to not turn lights on at all if sufficient natural daylight is present. An external photo

sensor can be connected directly to the occupancy sensor through the port on the rear EXT

of the device to provide additional daylight harvesting capabilities.

SETUP AND CONFIGURATION

• - Press or Short Timeout SHORT TIMEOUT - ENABLE SHORT TIMEOUT -

DISABLE to enable or disable mode. Short timeout allows the timout to Short Timeout

be set to 60 seconds when occupied for less than 90 seconds.

- Press or to enable or disable the LED of the •LED LED - ENABLE LED - DISABLE

device during normal operation.

- Press the desired button to set the •Timeout TIMEOUT - 30s/2m/5m/10m/15m/30m

timout.

Setup and configuration of the GLS-OIR-C-CN is performed using the

GLS-REMOTE-ODT/OIR remote. Refer to the GLS-REMOTE-ODT/OIR Operations Guide

(Doc. 7541) at www.crestron.com/manuals.

NOTE: Press the setup button on the sensor to acknowledge Cresnet identification. The specific patents that cover Crestron products are listed at patents.crestron.com.

Crestron, the Crestron logo, and Cresnet are either trademarks or registered trademarks of Crestron

Electronics, Inc. in the United States and/or other countries. UL and the UL logo are either trademarks

or registered trademarks of Underwriters Laboratories, Inc. in the United States and/or other countries.

Other trademarks, registered trademarks, and trade names may be used in this document to refer to

either the entities claiming the marks and names or their products. Crestron disclaims any proprietary

interest in the marks and names of others. Crestron is not responsible for errors in typography or

photography.

This document was written by the Technical Publications department at Crestron.

Return and Warranty Policies

Merchandise Returns / Repair Service

1. No merchandise may be returned for credit, exchange or service without prior authorization

from Crestron. To obtain warranty service for Crestron products, contact an authorized

Crestron dealer. Only authorized Crestron dealers may contact the factory and request an

RMA (Return Merchandise Authorization) number. Enclose a note specifying the nature of

the problem, name and phone number of contact person, RMA number and return address.

2. Products may be returned for credit, exchange or service with a Crestron Return

Merchandise Authorization (RMA) number. Authorized returns must be shipped freight

prepaid to Crestron, 6 Volvo Drive, Rockleigh, N.J. or its authorized subsidiaries, with RMA

number clearly marked on the outside of all cartons. Shipments arriving freight collect or

without an RMA number shall be subject to refusal. Crestron reserves the right in its sole

and absolute discretion to charge a 15% restocking fee plus shipping costs on any products

returned with an RMA.

3. Return freight charges following repair of items under warranty shall be paid by Crestron,

shipping by standard ground carrier. In the event repairs are found to be non-warranty,

return freight costs shall be paid by the purchaser.

Crestron Limited Warranty

Crestron Electronics, Inc. warrants its products to be free from manufacturing defects in materials

and workmanship under normal use for a period of three (3) years from the date of purchase from

Crestron, with the following exceptions: disk drives and any other moving or rotating mechanical

parts, pan/tilt heads and power supplies are covered for a period of one (1) year; touch screen

display and overlay components are covered for 90 days; batteries and incandescent lamps are not

covered.

This warranty extends to products purchased directly from Crestron or an authorized Crestron

dealer. Purchasers should inquire of the dealer regarding the nature and extent of the dealer's

warranty, if any.

Crestron shall not be liable to honor the terms of this warranty if the product has been used in any

application other than that for which it was intended or if it has been subjected to misuse, accidental

damage, modification or improper installation procedures. Furthermore, this warranty does not cover

any product that has had the serial number altered, defaced or removed.

This warranty shall be the sole and exclusive remedy to the original purchaser. In no event shall

Crestron be liable for incidental or consequential damages of any kind (property or economic

damages inclusive) arising from the sale or use of this equipment. Crestron is not liable for any

claim made by a third party or made by the purchaser for a third party.

Crestron shall, at its option, repair or replace any product found defective, without charge for parts

or labor. Repaired or replaced equipment and parts supplied under this warranty shall be covered

only by the unexpired portion of the warranty.

Except as expressly set forth in this warranty, Crestron makes no other warranties, expressed or

implied, nor authorizes any other party to offer any warranty, including any implied warranties of

merchantability or fitness for a particular purpose. Any implied warranties that may be imposed by

law are limited to the terms of this limited warranty. This warranty statement supersedes all previous

warranties.

TROUBLESHOOTING

The following table provides corrective action for possible trouble situations. If further

assistance is required, please contact a Crestron customer service representative.

GLS-OIR-C-CN Troubleshooting

Medium PIR Sensitivity Setting

The detection pattern for the medium PIR sensitivity setting is shown in the illustrations

below. The first illustration shows the side view of the detection range and the second

illustration shows the detection range based on the top view of the sensor.

Low PIR Sensitivity Setting

The detection pattern for the low PIR sensitivity setting is shown in the illustrations below.

The first illustration shows the side view of the detection range and the second illustration

shows the detection range based on the top view of the sensor.

Top View

8 1/2 ft (2.6 m)

Ceiling Height

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)



(m)

0 (0)

5 (2)

10 (3)

15 (5)

5 (2)

10 (3)

15 (5)

 (m)

20 (6)

25 (8)

20 (6)

25 (8)

(10)

30 (10)

Top View

8 1/2 ft (2.6 m)

Ceiling Height

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)



(m)

0 (0)

5 (2)

10 (3)

15 (5)

5 (2)

10 (3)

15 (5)

 (m)

20 (6)

25 (8)

20 (6)

25 (8)

(10)

30 (10)

0 ft (0 m)

8 ft (2.4 m)

8.5 ft (2.6 m)

10 ft (3 m)

12 ft (4 m)

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)

(m)

SIDE VIEW

0 ft (0 m)

8 ft (2.4 m)

8.5 ft (2.6 m)

10 ft (3 m)

12 ft (4 m)

(0)

(2)

(3)

(5)

(6)

(8)

(2)

(3)

(5)

(6)

(8)

(10)

(m)

SIDE VIEW

Product specificaties

Merk:	Crestron
Categorie:	Smarth home
Model:	GLS-OIR-C-CN

Heb je hulp nodig?

Als je hulp nodig hebt met Crestron GLS-OIR-C-CN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Smarth home Crestron

Crestron GLS-OIR-W-2500 Handleiding

9 Juli 2023

Crestron GLS-ODT-W-1200 Handleiding

5 Juli 2023

Crestron GLS-LCCT Handleiding

5 Juli 2023

Crestron GLS-PART-CN Handleiding

5 Juli 2023

Crestron GLS-OIR-C-CN Handleiding

4 Juli 2023

Crestron PP-100-W Handleiding

2 Juli 2023

Handleiding Smarth home

Nieuwste handleidingen voor Smarth home

Middle Atlantic LACE-44-OWP Handleiding

20 November 2024

Lutron FCJS-010 Handleiding

19 November 2024

Nanoleaf NL45-0800WT120E26 Handleiding

19 November 2024

Nanoleaf NL47-7003TW-7PK Handleiding

19 November 2024

Aqara Switch Module T1 Handleiding

19 November 2024

Paulmann 500.18 Handleiding

18 November 2024

Govee H7028 Handleiding

17 November 2024

Ferguson FS1SH Handleiding

17 November 2024

Ferguson Smart Hub FS2SH Handleiding

17 November 2024

Berker 24121636 Handleiding

17 November 2024