Crestron DSP-1282 Handleiding

Crestron Niet gecategoriseerd DSP-1282

Lees hieronder de 📖 handleiding in het Nederlandse voor Crestron DSP-1282 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 82 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

DO GUIDE

NOTE: Ensure that the computer that is running the Crestron Avia Audio tool and the DSP are on the same subnet.

Observe the following when connecting devices that are equipped with Dante

® network capability (DSP-1281 and DSP-1283):

• DANTE PRI ports should be connected to a gigabit switch serving the primary Dante network.

• (Optional) DANTE SEC ports should be connected to a gigabit switch serving the secondary Dante network.

• The primary Dante network should never mix with the secondary Dante network.

If unbalanced connections are required, refer to the following diagrams.

Front Panel

CAUTION: When connecting a Windows® 7 or Windows 8 computer to the COMPUTER port for the rst time, make sure the computer has a live connection

to the Internet. For more information, refer to Answer ID 5745 in the Online Help section of the Crestron website (support.crestron.com).

NOTE: The front panel’s COMPUTER port can be used to directly connect a computer running the Crestron Avia Audio tool, bypassing the LAN connection.

DSP-860/DSP-1280/DSP-1281/DSP-1282/DSP-1283

Crestron AviaTM Digital Signal Processors

The Crestron Avia™ DSP-860, DSP-1280, DSP-1281, DSP-1282, and DSP-1283 series of digital signal processors are functionally similar with varying

capabilities. For simplicity within this guide, the term “DSP” is used except where noted.

DO Install the Device

These devices occupy 1U of rack space. Use a #1 Phillips screwdriver to attach the two included rack ears to the device, and then mount the device into the

rack using four mounting screws (not included).

DO Connect the Device

Make the necessary connections as called out in the following diagrams. Connect power last.

Rear Panel

DO Check the Box

QUANTITY ITEM PART NUMBER

2 Bracket, Rack Ear, 1U 2032122

1 Cable, USB 2.0, A - B, 6’ (1.83 m) 2014966

1 Power Cord, 6' 7" (2 m) 2001134

DSP-860 Only

14 Connector, 3-Pin 2003575

DSP-1280, DSP-1281, DSP-1282, and DSP-1283 Only

20 Connector, 3-Pin 2003575

DSP-860

MIC/LINE INPUTS:

From microphone or

other audio sources

LINE OUTPUTS:

To audio ampliers or

other mixer inputs

POWER:

From

ac power outlet

LAN:

10/100/1000BASE-T

Ethernet to LAN

Ground

DSP-1280

MIC/LINE INPUTS:

From microphone or

other audio sources

LINE OUTPUTS:

To audio ampliers or

other mixer inputs

POWER:

From

ac power outlet

LAN:

10/100/1000BASE-T

Ethernet to LAN

Ground

DSP-1281

MIC/LINE INPUTS:

From microphone or

other audio sources

LINE OUTPUTS:

To audio ampliers or

other mixer inputs

DANTE PRI:

To primary

DANTE™ network

POWER:

From

ac power outlet

LAN:

10/100/1000BASE-T

Ethernet to LAN

DANTE SEC:

To secondary DANTE network

Ground

DSP-1282

MIC/LINE INPUTS:

From microphone or

other audio sources

LINE OUTPUTS:

To audio ampliers or

other mixer inputs

LAN:

10/100/1000BASE-T

Ethernet to LAN

VOIP:

To VOIP network

USB:

To Crestron RL® system or third-party

USB host device

POWER:

From

ac power outlet

PHONE:

To phone line

Ground

USB:

To Crestron RL system or third-

party USB host device

DANTE PRI:

To primary

DANTE network

DANTE SEC:

To secondary

DANTE network

MIC/LINE INPUTS:

From microphone or

other audio sources

LINE OUTPUTS:

To audio ampliers or

other mixer inputs

LAN:

10/100/1000BASE-T

Ethernet to LAN

VOIP:

To VOIP network

PHONE:

To phone line

POWER:

From

ac power outlet

DSP-1283

Ground

COMPUTER:

Direct computer connection to device

DSP-1281 and DSP-1283

Unbalanced Input Wiring

Signal

Jumper

Ground Signal Shield

Unbalanced Output Wiring

DO GUIDE DOC. 7647G (2040694) 06.18

Specications subject to change without notice.

DO Download the Crestron Avia Audio Tool

DSPs use the Crestron Avia Audio tool for conguration and operation. Download the Crestron Avia Audio tool from .www.crestron.com/software

DO Congure the Device

Once the DSPs are connected to the same subnet as the host PC running the Crestron Avia Audio tool, start the Crestron Avia Audio tool and perform the

following:

1. Click Add New Network DSP, located in the left-hand work space.

2. Click to launch the device discovery function. A list of units found on the subnet is displayed. Ethernet

NOTE: If a DSP is not listed, verify that all connections have been made and that all devices and the computer running the Crestron Avia Audio tool are on the

same subnet.

DO Operate the Device

Apply Power

When power is applied to the device, the LED on the front panel displays the following:PWR

• Green - Normal operation.

• Amber - Device is booting up.

• Amber/Green (Cycling) - No network connection.

Adjust Settings

Use the Crestron Avia Audio tool to control the device.

NOTE: When connecting to the DSP over Ethernet, ensure that the computer and device are on the same subnet.

Monitor Input and Output Levels (DSP-1281 and DSP-1283 Only)

Use the front panel’s analog VU meters to monitor input and output levels.

Reset the Device

Press on the front panel to restart the device.RESET

DO Connect to Crestron XiO Cloud Service (Optional)

The Crestron XiO Cloud™ service allows supported Crestron devices across an enterprise to be managed and congured from one central and secure

location in the cloud. Supported devices are precongured to connect to the service. Use of the service requires a registered Crestron XiO Cloud account.

NOTE: The device can be disconnected from the service from the tab in Crestron Toolbox™ software ( > Cloud Services Functions Device Info > Cloud

Services). For details, refer to the Crestron Toolbox help le.

To connect the device to the Crestron XiO Cloud service:

1. Record the MAC address and serial number that are labeled on the shipping box or rear panel of the device. The MAC address and serial number

are required in order to add the device to the Crestron XiO Cloud environment.

2. Do either of the following:

• Access the Crestron XiO Cloud service at https://portal.crestron.io.

• Register for a Crestron XiO Cloud account at www.crestron.com/xiocloud.

For detailed information about using the Crestron XiO Cloud service, refer to the Crestron XiO Cloud Service User Guide (Doc. 8214) at

www.crestron.com/manuals.

As of the date of manufacture, the products have been tested and found to comply with specications for CE marking.

This product is Listed to applicable UL® Standards and requirements tested by Underwriters Laboratories Inc.

Ce produit est homologué selon les normes et les exigences UL applicables par Underwriters Laboratories Inc.

Federal Communications Commission (FCC) Compliance Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:

(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired

operation.

CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the

equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is

no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

FCC Compliance Information (DSP-1283 and DSP-1282 only)

• Consult the dealer or an experienced radio/TV technician for help.

• This equipment complies with Part 68 of Federal Communications Commission (FCC) rules and requirements adopted by America’s Carriers

Telecommunications Association (ACTA). Each registered interface has a label that contains, among other information, a product identier in the format

US: CT UMM00BDMPS3300AEC. If requested, provide this information to the telephone company.

• If this equipment causes harm to the telephone network, the telephone company may temporarily discontinue service. If possible, advance notication is

given; otherwise, notication is given as soon as possible. The telephone company will advise the customer of the right to le a complaint with the FCC.

• The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of this equipment.

Advance notication and the opportunity to maintain uninterrupted service are given.

• If experiencing difculty with this equipment, please contact manufacturer for repair and warranty information. The telephone company may require this

equipment to be disconnected from the network until the problem is corrected, or it is certain the equipment is not malfunctioning.

• This unit contains no user-serviceable parts.

• This equipment is designed to connect to the telephone network or premises wiring using an FCC-compatible modular jack, which is compliant with Part

68 and requirements adopted by ACTA.

• The ringer equivalence number (REN) is useful in determining the quantity of devices you may connect to your telephone line and still have all of those

devices ring when your number is called. In most areas, the sum of the RENs of all devices should not exceed ve. To be certain of the number of devices

you may connect to your line as determined by the REN, call your telephone company to determine the maximum REN for your calling area.

• This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs. Contact your

state public utility commission or corporation commission for information.

Industry Canada (IC) Compliance Statement

CAN ICES-3(B)/NMB-3(B)

REN IC 0.1 (DSP-1283 and DSP-1282 only)

This product meets the applicable Industry Canada technical specications.

The Ringer Equivalence Number (REN) is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination of

an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed ve.

Le présent matériel est conforme aux specications techniques applicables d’Industrie Canada. L’indice d’équivalence de la sonnerie (IES) sert à indiquer le

nombre maximal de terminaux qui peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut consister en une combinaison

quelconque de dispositifs, à la seule condition que la somme d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas cinq.

ACTA Compliance Information

REN US 0.1B (DSP-1283 and DSP-1282 only)

The Ringer Equivalence Number (REN) indicates the maximum number of devices allowed to be connected to a telephone interface. The termination of an

interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices not exceed ve.

Rack Mounting Safety Precautions

•Elevated Operating Ambient Temperature: If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack environment

may be greater than room ambient temperature. Therefore, consideration should be given to installing the equipment in an environment compatible with

the maximum ambient temperature (Tma) specied by the manufacturer.

• : Installation of the equipment in a rack should be such that the amount of airow required for safe operation of the equipment is not Reduced Airow

compromised.

•Mechanical Loading: Mounting of the equipment in the rack should be such that a hazardous condition is not achieved due to uneven mechanical loading.

• : Consideration should be given to the connection of the equipment to the supply circuit and the effect that overloading of the circuits Circuit Overloading

might have on overcurrent protection and supply wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing this

concern.

•Reliable Earthing: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other

than direct connections to the branch circuit (e.g., use of power strips).

Electrical Connection

“This product must be connected to an earthed mains socket-outlet.”

• Finland: “Laite on liitettävä suojamaadoituskoskettimilla varustettuun pistorasiaan.”

• : “Apparatet må tilkoples jordet stikkontakt.”Nor way

• : “Apparaten skall anslutas till jordat uttag.”Sweden

The specic patent s that cover Crestron product s are listed at . www.crestron.com/legal/patents

The product warranty can be found at .www.crestron.com/legal/sales-terms-conditions-warranties

Cert ain Crestron products cont ain open source sof tware. For specic information, visit . www.crestron.com/legal/open-source- soft ware

Crest ron, the Crestron logo, Crest ron Avia, Crest ron RL, Crestron Toolbox, and Crest ron XiO Cloud are either trademarks or regist ered t rademarks of Crest ron Electronics, Inc., in t he United States

and/or other countries. Dant e is either a t rademark or registered trademark of Audinate Pt y Ltd. in t he United St ates and/or ot her countries. Windows is either a trademark or registered t rademark

of Microsof t Corporation in the United States and/or ot her count ries. UL and t he UL logo are either trademarks or registered t rademarks of Underwriters Laboratories, Inc. in the United States and/

or ot her countries. Other trademarks, regist ered t rademarks, and t rade names may be used in t his document to refer to eit her t he entit ies claiming the marks and names or t heir products. Crestron

disclaims any propriet ary int erest in t he marks and names of ot hers. Crestron is not responsible f or errors in t ypography or photography.

DO Learn More

Visit the website for additional information and the latest rmware updates. To learn more about this product, use a QR reader application on

your mobile device to scan the QR images.

Crestron Electronics

15 Volvo Drive, Rockleigh, NJ 07647

888.CRESTRON | www.crestron.com

Product specificaties

Merk:	Crestron
Categorie:	Niet gecategoriseerd
Model:	DSP-1282
Kleur van het product:	Black, Grey
Gewicht:	4100 g
Breedte:	439 mm
Diepte:	365 mm
Hoogte:	44 mm
LED-indicatoren:	Ja
Maximum resolutie:	- Pixels
Ingang stroom:	Ja
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Reset button:	Ja
Rack-montage:	Ja
Ethernet interface type:	Gigabit Ethernet
RJ-45 ports hoeveelheid:	2
Warmtedissipatie:	102 BTU/h
Rackcapaciteit:	1U
AC-ingangsspanning:	100-240 V
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	30 W
Bedrijfstemperatuur (T-T):	5 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent
Vermogenstoevoer locatie:	Achter